What Is Pave Setting: Stone Count, Metal Loss, And Cost
Pave setting is a bead setting repeated across a surface. Small stones sit in drilled seats, and tiny beads of metal are raised from the surrounding surface to pinch each stone in place.
The name comes from the French word for paved. The stones are not held by prongs and there is no rail around them. The grip is a set of metal beads, one per stone in the simplest version.
For a buyer the style is a counting exercise. Every stone needs a seat and every seat needs at least one bead. The quote follows that count, not the total carat weight on the tag.
The Short Answer
A pave setting holds many small stones with beads of metal instead of prongs. The setter drills a seat, drops the stone in, then lifts a sliver of metal over the edge of the stone with a graver.
A beading tool rounds that sliver into a bead. The work is done under a microscope for stones under two millimetres. The surface then reads as a sheet of light rather than a row of separate stones.
Two numbers decide the order. The first is the stone count. The second is how many beads each stone gets, because one stone can carry one bead or four.
Beads, Not Prongs
The sequence on the bench is short and it never changes. A hole is drilled into the metal, then a round burr cuts a shallow cup the size of the stone.
The stone goes into the cup. A graver lifts metal from the rim and pushes it over the girdle. A beading tool, a steel rod with a dimple in the tip, presses that metal into a round bead.
That description comes from the standard trade account of bead setting. Pave is the version where many stones sit close together and cover a surface.
The spacing is the tell. In a pave field the stones sit roughly a millimetre apart. The beads between them read as a grid of tiny dots, not as separate settings.
Compare that with a prong setting, where four fingers of metal rise above the stone. A prong shows the side of the stone. A pave field shows only the tables of the stones and the beads between them.
Stone Count Is The Quote
Two rings can hold the same total carat weight and differ by a factor of three in stone count. The setter is paid per stone, so the count decides the labour line.
The count comes from area and stone size. A round stone of 1.0 mm covers about 0.79 square millimetres of footprint. At 85 percent coverage, which is what close packing allows, one square centimetre holds about 108 stones.
Scale the stone up and the count falls fast, because area grows with the square of the diameter. At 1.7 mm the same square centimetre holds about 37 stones.
| Stone diameter | Footprint | Stones per cm² at 85% coverage |
|---|---|---|
| 1.0 mm | 0.79 mm² | 108 |
| 1.3 mm | 1.33 mm² | 64 |
| 1.5 mm | 1.77 mm² | 48 |
| 1.7 mm | 2.27 mm² | 37 |
The numbers are arithmetic, not a supplier claim. They assume round stones, a tight grid and 85 percent coverage. Treat them as a planning figure, and expect the layout drawing to move the count by a few stones.
Now run it on a real part. Take a band 2.2 mm wide with two rows of 1.3 mm stones and a circumference of 55 mm. Each row holds about 39 stones, so the ring needs about 78 stones.
Total carat weight follows the same arithmetic. Seventy-eight stones at about 0.01 carat each carry about 0.78 carat, and 117 carry about 1.17. The tag can say one carat in both cases, while the labour line does not move with the tag.
Add a third row and the count reaches about 117. The carat weight barely moves, because 1.3 mm stones are around 0.01 carat each. The setter, though, now has 39 more seats to cut and 39 more beads to raise.
One Bead Or Four
The word pave covers several bead patterns, and the labour differs fourfold between them. A buyer who prices by the name alone will be caught by this.
The simplest is single bead. Each stone is held by one bead on one side, and the stones sit close enough that the field looks continuous.
Bead and bright, also called grain setting in Europe, gives each stone four beads and cuts the metal around it into a small lowered box. It costs more beads, more graver work and more time.
A star setting engraves a short line from each bead into the surrounding metal. The line is decoration, and it adds a hand step that cannot be stamped.
Burnish setting, also called flush or gypsy setting, uses no beads at all. A polished tool pushes the metal over the stone, so the surface stays flat and the stone reads as a dot.
| Pattern | Beads per stone | Surface | Repair later |
|---|---|---|---|
| Single bead pave | 1 | Stones above the metal, beads as dots | Easy to re-bead, hard to match height |
| Bead and bright | 4 | Lowered box with a raised rim | Slow, four beads to lift per stone |
| Star setting | 4 plus engraved lines | Beads with rays cut into the metal | Very slow, the rays must be re-cut |
| Burnish or flush | 0 | Flat, stone flush with the surface | Metal must be pushed back, no bead to lift |
Ask which pattern the sample uses before you compare quotes. A four-bead field and a single-bead field look similar in a photo and are nowhere near the same job.
Metal Loss And Wall Thickness
Setting removes metal before it adds any. Each seat is a drilled hole with a burred cup, and the bead comes from the metal that sits between the stones.
That is why a pave band is thinner after setting than the same band before it. The more rows of stones, the less metal is left in the walls.
The request that follows is simple. Ask for the wall thickness left after setting, in millimetres, and ask what the band weighs before and after the stones go in.
Weight before and after also catches a shortcut. A light band with a wide field of stones can only hold those stones if the walls were cut thin. Thin walls are where a band bends and sheds stones.
Resizing is the second limit. A paved band cannot always be sized the way a plain band can. The seam runs through the field, so the stones near it have to come out first.
Write the answer into the order notes, and keep the note with the layout drawing. A resale customer will ask the same question a year later, and the note is the only record.
Ask for the maximum resize the workshop will accept on that design, in ring sizes, and put the answer in the order notes. A resale customer will ask the same question a year later.
Reading A Setting Quote
A setting quote usually has three lines. There is a per-stone rate, a layout or setup charge, and a finishing charge for polishing and plating.
If the factory quotes per piece instead, divide by the stone count to compare. Two quotes per piece tell you nothing until both are reduced to the same unit.
The per-stone rate also has to name the pattern. A single-bead rate and a four-bead rate are different jobs, and a quote that says only setting is not a quote yet.
Stone supply is the line most buyers miss. Melee can come from the factory or from your own parcel, and the two routes carry different risk on size, colour and count.
If the factory supplies, ask for the melee size in millimetres, the sieve range and the count per carat. If you supply, ask who carries the loss when a stone breaks in the seat.
Finishing order matters as much as the rate. Polishing happens before plating, and plating covers the beads, so a re-polish after wear takes metal off the very beads that hold the stones.
The plating step is covered in how plating and PVD split on this site. It applies to a pave ring exactly as it does to a plain one.
The Four-Point Check On Arrival
Inspection of a paved field takes a loupe and four passes. It does not take a lab, and it catches most of the faults that reach a customer.
First, count. Work row by row and compare the total against the invoice. A short count is the most common fault and the easiest to prove.
Second, look at bead height. Beads should sit level with each other across the field, and none should stand proud of its neighbours.
Third, check stone level. Every table should sit in one plane. A stone that has dropped below that plane is loose now, and it will leave later.
Fourth, weigh the piece and compare it with the approved sample. A full count on a light piece means the walls were cut thin to make room for the seats.
Photograph each stage at 10 times magnification, then again at 20 times on a single row. Those photos are the record if a claim arrives six months later.
The bench that cut the seats is the one that has to fix them. Keep the factory in the conversation until the last stone is checked. The page on the factory that owns the setting bench covers how to pick that partner.
The Customs Line Counts Pieces
Customs does not care about the setting pattern. It cares what the piece is made of and how it is counted, and the two answers decide the rate.
A gold ring set with diamonds sits in 7113.19.50.91, articles of jewelry of gold, at 5.5 percent. The unit of quantity is pieces, not grams.
Silver falls in 7113.11.50 at 5 percent and is declared by weight in grams. A clasp or a part on its own sits in 7113.19.30 at 5.8 percent.
The contrast to know is imitation jewelry. A brass ring set with cubic zirconia sits in 7117.19.90 at 11 percent, because the chapter note excludes stones and precious metal from that definition.
Set a real diamond into that same brass ring and chapter 71 pulls it back in. The stone decides the chapter, which is why the invoice has to name the stone and not just the style.
One counting rule trips up earrings. Each piece is counted on its own, so a pair of studs is two pieces. The studs order order is where that rule bites most often.
Six Lines For A Setting Quote
Put these in writing before a sample is made, and the quote becomes comparable with the next one.
One: the stone diameter in millimetres and the sieve range. Two: the bead pattern, stated as single bead, four bead or burnish.
Three: the stone count from the layout drawing, per row. Four: the wall thickness left after setting, in millimetres.
Five: who supplies the melee, and who carries loss on a broken stone. Six: the maximum resize in ring sizes, and whether the stones at the seam come out first.
Packing travels with the ring and has its own timeline. The box order belongs in the same conversation, not in a separate one later.
Questions Buyers Ask About Pave Setting
Is pave the same as micro-pave?
The technique is the same. Micro-pave is the trade name for the smallest end, usually stones under about 1.3 mm set under a microscope, and the tighter spacing is what raises the labour.
Do paved stones fall out?
They can, because the bead is a small piece of metal that wears with the surface. A bead that flattens lets the stone ride high, and the next knock takes it out.
Can a paved band be resized?
Often, but not always. The seam runs through the field, so the workshop may have to lift the stones near it before soldering and reset them after.
Does each small stone come with a certificate?
No. Melee of this size is sold as a parcel described by size and grade range, and the major labs do not issue individual reports below roughly 0.15 carat.
How should a pave ring be cleaned?
Warm water, a soft brush and a wipe. Skip the polishing cloth on the field, because every pass with an abrasive works on the beads that hold the stones.
What is the biggest quality risk in the quote?
Thin walls. A wide field of stones on a light band is the pattern that fails first, and the invoice rarely shows the wall thickness that made it possible.
How many stones are on the last paved piece you bought, and did the invoice state the count? Paste the line and I will read it against the layout.
Send the stone diameter, the row count and the band width from your drawing. We will return the stone count, the beads the bench has to raise, and the wall thickness to write into the order before the sample is cut.
Send The Drawing
Questions & Comments
We read every one and reply within 24 hoursHow many stones are on the last paved piece you bought, and did the invoice state the count? Paste the line and I will read it against the layout.