What Is Gold Filled Jewelry: The 1/20 Rule
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Gold Filled Jewelry: Why It Outlasts Plating

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 16, 2026 · 10 min read

Gold filled is a base metal with a sheet of gold alloy bonded to it by heat and pressure. The federal rule sets one line for the name: at least 1/20 of the article weight must be that gold layer.

That single fraction is the difference between a bracelet that survives two summers and one that shows brass in a month. It is also the number most listings leave out.

This page reads the rule as a buyer would. It compares the five labels that sit next to each other in a catalog. It shows where a gold filled piece still wears out, and which lines to put in a quote.

Gold filled chain and a magnifier on a beige surface, showing the gold layer at a cut end
Five labels, one question: how much gold is actually bonded to the base metal.

The Short Answer

Gold filled jewelry starts with a brass or copper core. A gold alloy sheet is bonded to it under heat and pressure, then the sandwich is rolled to thickness.

The layer is not painted on and it is not grown in a bath. It is a mechanical bond that becomes part of the metal. That is why a gold filled ring can be cut, soldered and polished without the gold flaking off.

The name is only legal when the alloy is at least 10 karat. It must also make up at least one twentieth of the weight of the whole piece. Below that share, the same product is called rolled gold plate.

The 1/20 Rule, Read Line By Line

The wording sits in the jewelry guides at 16 CFR 23.3. Two paragraphs do the work, and both are short.

Paragraph (b)(6) says a seller may not use the term gold filled unless the layer was applied by a mechanical process. It must also be thick enough across all significant surfaces to last.

Paragraph (c)(2) then fixes the numbers. The alloy must be at least 10 karat. At 1/40 of the article weight, the piece may be called rolled gold plate or gold overlay. At 1/20, it may be called gold filled.

In decimal terms, that is 2.5 percent of the weight for rolled plate and 5 percent for gold filled. On a 4 gram ring, the gold filled layer carries about 0.2 grams of alloy.

One more condition hides in the same clause. The karat number has to sit immediately before the term, and it has to be as visible as the term itself. A mark that reads only GF, with no karat, does not meet the test.

The five labels a jewelry catalog uses, and the minimum behind each one
LabelHow the gold is attachedMinimum in the ruleUnit the rule uses
Gold filledMechanical bond, heat and pressure1/20 of article weight, 10K or betterWeight share
Rolled gold plateSame process, thinner layer1/40 of article weight, 10K or betterWeight share
Gold plate, electroplatedElectrolytic bath on all significant surfaces0.175 micron of fine goldThickness
Heavy gold electroplateElectrolytic bath, longer cycle2.5 microns of fine goldThickness
VermeilGold over sterling silver2.5 microns, 10K or betterThickness

Put the two units side by side and the confusion ends. Gold filled is measured by weight share. Plating is measured by thickness. A seller who quotes microns for a gold filled item is answering a different question.

Comparison chart of the five jewelry labels with weight share and thickness minimums
Weight share and thickness are different rulers. Mixing them is how a thin plate gets sold as gold filled.

Reading A Mark In Ten Seconds

A gold filled stamp that meets the rule reads like a fraction, a karat and two letters. The common form is 1/20 14K GF.

Each part answers a question. The fraction is the weight share of gold alloy. The karat is the fineness of that alloy. The letters name the process.

Now read a second stamp: 14K GF, with no fraction. It names the alloy and the process but drops the share, which is the number a buyer actually needs.

Read a third: 18K HGE. That is heavy gold electroplate, a bath process measured in microns. It is a valid label, and it is not gold filled.

Ask for a photo of the stamp on a real piece, not a rendered one. Stamps are shallow, and a shallow stamp wears away faster than the gold does.

Where It Still Fails

Gold filled outlasts plating because the gold is thick and joined to the core. It is not a lifetime finish, and the wear is not spread evenly.

Three places go first. Three parts take constant rubbing against skin, fabric or another metal part. They are the bottom of a ring shank, the edge of a clasp and the post of an earring. The earring post is the smallest part in the order and the first to be judged.

On a chain, the jump rings and the spring in the clasp carry the load. A bracelet that is opened twice a day wears at the clasp long before the links fade.

The fraction also hides a geometry problem. One twentieth of the weight is a share, not a depth. Roll the same alloy onto a thin wide sheet and the gold sits closer to the surface than it would on a thick narrow band.

Chemicals matter as much as friction. Chlorine, perfume and abrasive polish all shorten the life of the layer. A gold filled ring is the wrong choice for daily wear in a pool.

Repair is the hard limit. A worn gold filled ring cannot be re-plated back to its original look, because the label describes a bonded sheet and not a bath finish.

Resizing a ring leaves a solder seam. Ask the factory which solder it uses and whether the colour matches the layer, then ask for a photo of a resized sample.

Diagram of a ring, clasp and earring post marking the three wear points on gold filled jewelry
The three wear points to check on a return, in the order they usually fail.

The assay side has its own tolerance. Under the National Stamping Act, a karat mark allows three parts per thousand on a piece without solder. With solder, the allowance is seven parts per thousand.

That tolerance is not a licence to underfill. It exists so a legal mark survives a normal assay, and a supplier who leans on it will fail a tighter house standard.

What It Costs To Buy Right

Price follows the gold, and the gold is a small share of the piece. The arithmetic is short enough to do in a meeting.

Take a 4 gram ring at 1/20 and 14 karat. The alloy layer is 0.2 grams, and 14 karat is 58.3 percent fine gold, so the ring holds about 0.117 grams of pure gold.

Multiply that by the spot price and you have the metal value. Everything else in the quote is brass, labour, finishing, packing and freight.

Fine gold inside a 14 karat gold filled piece, by article weight
Article weightAlloy at 1/20Fine gold at 58.3%
2 grams0.10 g0.058 g
4 grams0.20 g0.117 g
8 grams0.40 g0.233 g
16 grams0.80 g0.467 g

The table is arithmetic, not a price list. It shows why a heavier gold filled chain holds more gold than a lighter pendant, and why the two cannot be compared on price alone.

This is why the label matters more than the price per gram. Two rings can weigh the same and hold five times different amounts of gold.

Against that, a 0.175 micron electroplate on the plating route holds so little gold that the metal value disappears into rounding. The buyer is paying for the process, not the metal.

The same arithmetic explains a quote that looks too low. Drop the gold share from 1/20 to 1/40 and thin the core, and the metal line falls. Nothing on the invoice announces it.

Nickel is the other cost line that never appears on an invoice. Ask for the base metal by name and for a nickel release test report, and check the report covers the parts that touch skin.

How To Keep It Looking Right

Care for a gold filled piece is close to care for solid gold, with one extra rule about abrasion.

Take it off before a shower, a swim or a workout. Chlorine is the fastest way to dull the layer, and sweat left on a ring overnight works on the edges.

Wipe it with a soft cloth after wear. Skip the polishing compound, because every pass with an abrasive takes a little of the layer with it.

Store pieces apart, or in a pouch. A chain rubbed against a bracelet for a year loses more gold than a chain worn alone.

Check the wear points once a season. A bright line at the shank or a dull patch at the clasp edge is the warning, and it appears before the brass shows through.

The same habits decide resale. A gold filled piece has almost no melt value, so the buyer is paying for the finish and the story, not the metal.

That is not a fault in the product. That is the trade a buyer makes. Five percent gold at a fraction of the price, in exchange for a piece that is not an investment.

The Customs Line Calls It Base Metal Clad

Customs does not use the marketing label. Heading 7113 covers jewelry of precious metal, and 7113.20 covers jewelry of base metal clad with precious metal.

Gold filled sits in 7113.20 by that text, and the current rate table lists the subheadings under it. The subheadings split by article type, and the general rate for other articles is 5.2 percent.

Clasps and parts fall in 7113.20.30 at 5.8 percent. Rope and mixed link chain sit at the same 5.8 percent, so a chain order can land higher than a pendant order of equal value.

Solid gold does not help here. Other precious metal jewelry sits in 7113.19 at 5.5 percent, and sterling silver in 7113.11.50 at 5 percent.

That gap is worth knowing before a price meeting. Gold filled saves money on material, not on duty, and a quote that promises a tariff advantage is answering the wrong question.

The unit of quantity is grams on these lines. An invoice built in pieces and carats will be rebuilt by the broker, so send weights in grams from the start.

Table of jewelry tariff subheadings with general duty rates and units of quantity
The gold filled saving is in the metal, not the tariff line.

One classification habit is worth fixing early. Describe the article as jewelry of base metal clad with gold alloy, name the karat and the fraction, and let the broker pick the subheading.

If the invoice says gold jewelry, the entry rests on a claim the product cannot support. The correction lands after the goods arrive.

Six Lines For A Quote

The factory that bonds and finishes the piece can answer these in one message. If it cannot, the sample is not worth the freight.

One: the karat and the fraction that will be stamped, for example 1/20 14K GF. Two: the base metal by name, plus a nickel release test report covering the skin contact parts.

Three: the solder used at the seam, and whether its colour matches the layer after polishing. Four: the weight tolerance per piece, in grams, at the packing stage.

Five: the wear test behind the durability claim, with the method and the hours. Six: any flash plating on top of the gold layer, which has to be disclosed. Packing is quoted with the box and pouch order, not with the metal.

The plating question is not a technicality. The rule treats a gold layer covered with a base metal and then washed with gold as a separate case. It must be described as such.

Questions Buyers Ask About Gold Filled Jewelry

Is gold filled the same as solid gold?

No. The core is brass or copper, and the gold is a bonded alloy sheet. The gold share is at least one twentieth of the weight, which is why the piece costs a fraction of solid gold.

How is it different from gold plated?

Gold filled is judged by weight share, so the layer is thick and joined to the core. Gold plate is judged by thickness, with an electroplated minimum of 0.175 micron of fine gold.

Will a gold filled ring turn my finger green?

Not while the layer is intact. Once it wears through at a friction point, the brass core can leave a mark on skin, and that is the moment to stop wearing the piece.

Can a jeweller resize it?

Yes, if the workshop uses a solder that matches the layer. Ask for the solder type and a photo of a resized sample before placing the order, because a colour mismatch shows at the seam.

Is vermeil a better buy?

Vermeil is a different product: gold of at least 2.5 microns over sterling silver. It carries a silver core and a higher material cost, so compare it against solid silver, not against brass.

What test report should I ask for?

Ask for a nickel release report on the parts that touch skin, and for the melt and assay record behind the karat stamp. A supplier who cannot send either is guessing at the label.

Which label came on the last piece you bought, and did it carry a fraction? Paste the stamp and I will read the three parts with you.

THE STAMP

Send a photo of the stamp, the karat and the fraction, and one line on the base metal. We will tell you whether the label meets the rule, what the layer is worth in metal, and which tariff subheading the invoice should name before the first sample ships.

Send The Stamp Photo

Questions & Comments

We read every one and reply within 24 hours

Which label came on the last piece you bought, and did it carry a fraction? Paste the stamp and I will read the three parts with you.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x