What Is Headphone Impedance: The Number That Is Not Difficulty
Headphone impedance is the load the amplifier sees, in ohms.
It tells you the shape of that load. It does not tell you how loud the headphone gets, and it does not tell you whether your phone can drive it.
Those two questions are answered by a second number, sensitivity, and the pair only makes sense together.
This article does the arithmetic that most explainers skip, then turns it into six lines a buyer can ask for.
The Short Answer
Impedance is alternating-current resistance. A headphone presents it to whatever is driving it, and the figure in ohms describes how much voltage is needed for a given current.
High impedance means the same current needs more voltage. Low impedance means the same voltage pushes more current.
Neither is better. Each one moves the work to a different part of the amplifier.
What people usually mean by “hard to drive” is something else. It is a combination of how much voltage the headphone needs and how sensitive it is.
A 22 ohm planar can be harder to drive than a 300 ohm dynamic. That sentence sounds wrong until you see the two numbers side by side.
Two Scales, One Logarithm
Sensitivity is quoted as sound pressure per milliwatt, or sound pressure per volt. They are different measurements and they are not interchangeable.
The first is written dB/mW. It says how loud the headphone plays when it absorbs one milliwatt of power.
The second is written dB/V. It says how loud it plays when the source applies one volt, whatever current that draws.
Your source is a voltage device. It holds a voltage and lets the current follow. So the second unit is the one that predicts what you will hear.
The conversion is a single logarithm. Add ten times the base-ten logarithm of one thousand divided by the impedance.
In symbols, the voltage figure equals the power figure plus ten log of a thousand over Z. One worked example makes it concrete.
A 300 ohm headphone at 97 dB/mW becomes about 102 dB/V, because the log term adds roughly five decibels.
A 32 ohm headphone at the same 97 dB/mW becomes about 112 dB/V, because the log term now adds roughly fifteen.
Same power figure, ten decibels apart on a voltage source. That is the whole trap, and it is one line of arithmetic.
The Same Loudness At Two Impedances
A published measurement set makes the trap impossible to argue with. It lists seven headphones, giving each one in decibels per milliwatt, in decibels per volt, and in ohms.
The two Sennheiser models sit at 300 ohms and 107 dB/mW. In voltage terms they are 112 dB/V.
The Audeze sits at 22 ohms and 96 dB/mW. In voltage terms it is 112.5 dB/V.
Read the power column and the Sennheisers look eleven decibels louder. Read the voltage column and the two are within half a decibel.
That is why the same listening test found both marginal on a phone. Both need roughly the same voltage, and a phone has little of it.
Two cheaper pairs in the same list sit at 32 and 63 ohms. Their voltage figures are 117 and 118 dB/V, which is five decibels more for the same input.
Five decibels is not a subtle difference on a portable device. It is the difference between marginal and comfortable.
None of those headphones changed. Only the unit did.
What One Number Cannot Say
A sensitivity figure is a single point. It is measured at one frequency, usually a thousand hertz, and it describes one moment in the response.
Two products with identical numbers can still differ in tone, because the number says nothing about the rest of the curve.
The conventions differ as well. Some makers measure at one milliwatt, some at one volt, and some on a coupler that is not the one you own.
The published guidance on the subject is blunt about it. These figures are approximate, and they are best read with a few decibels of slack.
That slack is not a flaw. It is the honest width of a single-number summary, and it is why a sheet should name the test behind it.
Two Ways To Be Hard To Drive
Once voltage and current are separate, “hard to drive” splits into two problems that need different fixes.
Short of volts. A high-impedance dynamic headphone, from about 250 to 600 ohms, cannot draw much current. It needs voltage swing, and a phone runs out of swing first.
The symptom is simple. The volume control reaches its end and the music is still quiet. Nothing distorts, nothing breaks, there is simply no more level.
Short of current. A planar magnetic headphone often sits at a low load with a low loudness figure. Its ohm figure looks friendly and means nothing here.
This load asks for current, and a weak output sags or clips instead. The symptom is distortion or a collapse on loud passages, not a lack of volume.
There is a third case at the other end. A very sensitive in-ear monitor, around 105 to 125 dB/mW, is loud from anything you plug it into.
Its problem is the opposite one. It exposes the noise floor of the source, and it reacts badly to a high output impedance.
What The Port Can Actually Deliver
A phone or a laptop runs on a small battery, so its output voltage is limited. That single fact explains most of the advice in this field.
Acoustic output follows input power. A low-load headphone draws more power from the little voltage a phone offers. That is why small designs are usually low impedance.
The cost is current. That same load demands current the output stage may not deliver cleanly, and the published note on the subject says it often raises distortion.
A high load flips it. The headphone draws less current for the same loudness, so distortion is often lower and battery life may even improve.
What it will not do is damage the phone. A high-impedance load is a light load, and the risk there is only that the maximum level is too low.
The reverse is riskier. A very low load can overload an output that was not built for it, so check the maker’s minimum recommended load.
Gain, And The Volume Control
Gain is how much the output multiplies the signal. It is a separate setting from power, and it is usually hidden.
A quiet load forces the volume control to its end. A loud one forces it into the bottom of its travel, where the two channels often disagree.
That is why studio outputs sometimes offer several gain ranges. One published design uses three, so that a sensitive in-ear and a 600 ohm pair both land in the usable part of the dial.
Raising gain does not add power. It lifts the noise with the music, so a load that needs gain rather than voltage will still sound strained.
There is a noise angle too. Noise from the output is reproduced louder as the load falls. That is why sensitive in-ears hiss where full-size pairs stay silent.
The Impedance Of The Source
The headphone is only half the circuit. The output has its own impedance, and the two form a divider. The cable and connector in between are the third part.
That divider is why the frequency response of some headphones changes when you change the source. The load is not a flat resistor at every frequency.
A dynamic driver rises to a peak at its resonance, often in the bass. Where the load rises, a high source impedance drops more of the signal, and the shape changes.
The working rule is a ratio. Keep the source impedance at or below one eighth of the headphone’s, and the divider stays out of the way.
Above that ratio, the effect is audible on multi-driver in-ears and it loosens the bass of low-impedance headphones. The rule is a rule of thumb, not a law.
Good studio outputs sit far below it. One published example quotes an output impedance of about 0.1 ohms, which is a very high damping factor against any headphone.
Ask for the output impedance as a number. “Designed for headphones” is not a number, and it cannot be checked against a ratio.
The Load Is Not A Resistor
The printed figure is one point on a curve. The real load moves with frequency, and that movement is what the ratio rule protects against.
A dynamic driver reaches a peak at its resonance, usually in the bass. The coil and the suspension trade energy there, and the load rises with them.
Multi-driver in-ears go further. A crossover splits the signal between small armatures, and each one adds its own bump and dip to the total load.
Push that uneven load through a high source impedance and the tone changes. The divider divides differently at every frequency, so the shape moves with it.
So ask for the curve, not only the printed number. A product that can show its own curve has measured its own design.
Which Load Needs Which Amplifier
Four load types cover almost every product on a shelf. Each one fails in its own way.
| Load | What it needs | What goes wrong | What to check |
|---|---|---|---|
| High-impedance dynamic, 250 to 600 ohms | Voltage swing | Too quiet at full volume | Sensitivity in dB/V |
| Low-impedance dynamic, 32 to 80 ohms | Clean current | Distortion, source noise | Output impedance against the ratio |
| Low-sensitivity planar | Current, and voltage | Clips on loud passages | dB/mW at its own impedance |
| Sensitive in-ear, 105 dB/mW and up | Silence in the output | Hiss, a shifted response | Noise floor, output impedance |
The table has no “better” row. A product is matched or it is not, and the match depends on both halves of the circuit.
What The Sheet Says
Most of the confusion is an ohm figure standing in for a loudness figure.
| What it says | What it answers | What to ask |
|---|---|---|
| “32 ohm” | The shape of the load | What is the sensitivity in dB/V? |
| “300 ohm, studio grade” | A heavier voice coil | Will my source reach 100 dB? |
| “Sensitivity 97 dB” | Nothing, until the unit is named | Per milliwatt or per volt? |
| “Drives up to 600 ohm” | A claim about voltage swing | How many volts into that load? |
| “400 mW output” | Power into one unnamed load | Milliwatts at 32 ohm and at 300 ohm? |
| “Output impedance 0.1 ohm” | A ratio worth having | Is it below one eighth of my headphone? |
Every line in that table is true. Each one is true about half a circuit.
Six Lines For The Sheet
A headphone and an amplifier are a pair. Six lines describe the pair well enough to predict the result.
One. The stated impedance, and how it varies with frequency. A single number hides the bass peak.
Two. The sensitivity, with the unit written out. Per milliwatt or per volt, never just decibels.
Three. The same sensitivity converted to the voltage figure at that impedance. That is the number your customer can use.
Four. The maximum level reached from a stated source voltage, so a phone can be compared with a desktop output.
Five. The output impedance of the source, as a number, so the one-to-eight ratio can be checked.
Six. The minimum recommended load, and the noise floor. Those two decide whether sensitive in-ears are usable.
Six lines make a pair predictable. The sheet an order is built on is where they belong, not in a marketing paragraph.
The same discipline applies to the rest of an audio product. A speaker has the same load question at a larger scale, which is why a speaker programme is specified the same way.
The smallest version of the same problem sits in the two-radio arrangement inside true wireless buds. There the output, the radio and the battery share one shell.
Ten Minutes With A Sample
You do not need a measurement rig to catch a mismatch. Five checks cover the common cases.
Max level. Play a quiet, well-recorded track on the intended source and turn the volume to its end. If it never gets loud, the load is asking for volts.
Two pairs. Swap between a 300 ohm pair and a 32 ohm pair at the same volume setting. The gap is the voltage sensitivity difference, and it is usually bigger than the ohm figures suggest.
Hiss. Turn the volume up with nothing playing. Audible hiss means a noisy output, and a sensitive in-ear will find it.
Bass swap. Play a bass-heavy track, then change source. If the bass quantity moves, the source impedance is too high for that load.
Dense passage. Play something loud and busy. A collapse or a hardening is a current limit, not a volume limit.
Five checks, one sample and one familiar track. They will tell you more than two paragraphs of ohms.
Send me the specification sheet for a headphone or a small amplifier you are considering. I will convert the sensitivity into the unit that predicts loudness, check the source impedance against the one-to-eight ratio, and tell you which pairing will disappoint. No cost, no obligation.
Check The PairingQuestions Buyers Ask
Is higher impedance better?
No. It moves the work from current to voltage. A high load is easier on the amplifier and harder on the source, and which side matters depends on what you plug it into.
Can a phone drive a 300 ohm headphone?
Often yes, and it will not damage anything. The limit is level: a typical dongle supplies about one volt, which puts a 102 dB/V pair near 100 dB at full output.
What does 32 ohm actually tell me?
That the load is shaped for a small voltage swing, which is why most portable headphones sit there. It says nothing about how loud it gets.
Why do my in-ear monitors hiss?
Because they are very sensitive and the output is not silent. Noise that is inaudible on a full-size pair becomes obvious on an in-ear, and a high output impedance makes it worse.
Do planars always need an amplifier?
Not always, but often. Their low impedance hides a low sensitivity, and the load that follows is current. A weak output distorts rather than simply running out of volume.
Is 600 ohm a quality grade?
No. It is a load value. Some studio headphones use it, and so could a poor one. The grade is in the measured response and distortion, not in the ohms.
Questions & Comments
We read every one and reply within 24 hoursIf a headphone or a small amplifier sheet crosses your desk, send it. I will convert the sensitivity into the unit that predicts loudness and check the pairing.