What Is LDAC: The 990 kbps That Rarely Arrives
LDAC is a Sony codec for short-range wireless audio. Its highest rate is 990 kbps.
That number is a ceiling, not a state. The codec ships set to choose its own rate, and it spends most of its life well below that ceiling.
This article covers what each of its three rates actually delivers, and what decides which one you get. It also covers where the bandwidth is wasted even when the link is good.
It also covers the part that matters when you are buying rather than listening. LDAC needs a licensed decoder, and that changes what a factory can promise you.
The Short Answer
LDAC is a lossy audio codec developed by Sony for streaming music over a short-range radio link. It is not a file format and not a streaming service.
Its selling point is bandwidth. Sony advertises three times the data of the baseline codec, measured against 328 kbps at 44.1 kHz.
In practice that means three fixed steps: 330, 660 and 990 kbps. The manual settings differ slightly by sample rate, at 303, 606 and 909 kbps for the 44.1 kHz family.
There is one unusual detail in the licensing. The encoder is open source and sits inside Android, so almost any modern phone can send it. The decoder is proprietary, so the receiving product needs a licence.
That asymmetry explains a lot of what follows. Sending LDAC is nearly free. Receiving it is not.
What Each Rate Actually Delivers
The three steps are not three settings of the same quality. They behave like three different codecs.
One published measurement of a retail phone puts numbers on it. The test swept a signal through the codec and read the output at each rate.
At 990 kbps the response runs to about 47 kHz before it rolls off. That is enough to pass a high-resolution file on paper.
At 660 kbps the roll-off is steep and lands at 30 kHz. That is still above hearing, and it is the rate most phones actually choose.
At 330 kbps a steep filter cuts in just before 18 kHz. That is below the ceiling of a CD, and it is audible on cymbals and strings.
The noise floor separates them further. At 990 kbps it sits near -116 dB up to 15 kHz. At 660 it reaches about -74 dB at 15 kHz. At 330 it climbs to -35 dB.
Those last two numbers are the ones a buyer should keep. A noise floor of -35 dB in the highest octave is not a small difference from a CD. It is a different product.
| Rate | Measured cut-off | Noise floor at 15 kHz | What it demands |
|---|---|---|---|
| 990 kbps | about 47 kHz | about -98 dB | a link that never drops near -60 dBm |
| 660 kbps | 30 kHz, steep | about -74 dB | the usual default, some headroom |
| 330 kbps | 18 kHz, steep | about -35 dB | a link that has already given up |
The table is also a map of the fallback. A product does not sit at one row. It walks down them as the link worsens.
The Mode That Decides Your Day
Out of the box, LDAC is set to choose its own rate. The codec picks 330, 660 or 990 by watching the link, and it moves between them without asking.
Sony describes this as a feature, and it is one. Stable sound beats a drop-out. The catch is that the highest row is rarely the row in use.
A test of six phones at arm’s length found exactly one that picked 990. Two picked 660. Two sat at 330 while doing nothing more demanding than playing music.
To reach the highest rate, a user has to open the developer options and force it. That is not a setting a normal buyer will ever find.
Then the room gets a vote. Signal strength decides what the radio can sustain, and the published guide puts the boundaries in plain terms.
Above about -60 dBm, a real-time high-bandwidth stream is safe. Around -70 dBm it is not. Below -80 dBm there is no real-time stream at all.
The two highest rates cut it fine. They begin to stutter just below -60 dBm, which is the level you get with a hand over the phone.
Measured on ears and in pockets, true wireless buds came in as low as -63 dBm. Two generations of a well-known Sony headset averaged -49 and -51, with lows near -60.
So the honest reading of a box that says 990 kbps is this. The product can do it, in a room where nothing is in the way, if someone has forced the setting.
The Arithmetic Nobody Prints
Two multiplications decide whether a wireless codec can be lossless. Both are easy, and neither appears on a product page.
A CD carries two channels of 16-bit samples, 44,100 times a second. Multiply it out and you get 1,411 kbps.
LDAC’s ceiling is 990 kbps. That is lower than the disc it is being compared with, so roughly a third of the data has to go.
That single comparison settles the argument. Whatever else LDAC does well, it cannot be lossless for CD audio.
A high-resolution master is further out. Two channels at 24 bits and 96 kHz is 4,608 kbps, and 990 is about a fifth of it.
This is why the certificate is worded the way it is. Sony states that the mark is satisfied at the 990 kbps transfer rate. The mark describes what the link carries, not what comes out of it.
None of that makes the codec bad. It makes the word “high-resolution” a statement about the source file, not about the trip.
Three Ways The Bandwidth Is Wasted
Suppose the link is clean and the phone is forced to 990. The bits can still be spent on nothing.
Upsampling. A 44.1 kHz track played at 96 kHz carries twice the samples and no more music. The encoder spends its bits describing an interpolation.
Switching that setting buys nothing. It costs battery on both ends and makes the link less stable for no audible gain.
Re-encoding. This is the common one. A streaming service already sends 256 kbps AAC. Decoding it and encoding again at 990 does not recover what the first pass threw away.
It encodes the damage. The extra bits describe the first codec’s artifacts rather than the original recording.
Phantom depth. A 16-bit master has no information below its sixteenth bit. Setting the codec to 32 bits pads the word without adding a sample.
All three share a shape. The number on the crate grows and the content does not.
There is a fourth case, and it is not waste so much as arithmetic. In a gym or a street, the link falls to 330 whatever the file is, and every bit above that was never available.
Who Owns Each Link In The Chain
Audio out of a phone and into a headset passes five links. Each one can cost quality, and each one belongs to somebody different.
The master. The studio’s file. A lossy streaming copy has already lost what it lost, and nothing downstream returns it.
The encoder. The phone, usually. Since Android 8, the encoder is part of the platform, so any handset maker can ship it without paying Sony.
The radio. Two antennas and a shared band. This is the link that decides which of the three rates you actually get.
The decoder. The headset. This is the proprietary half, and it is where the licence sits.
The driver and the amplifier. The last physical step. The rest of the speaker build decides what those two can do. A codec cannot fix a driver that distorts, and it cannot widen a diaphragm.
A product page usually describes the second link and stays quiet about the rest. The second link is the free one.
For a buyer, the useful question is about the fourth. Which decoder is inside, and who licensed it?
Why A Factory Cannot Just Add LDAC
This is the section for anyone sourcing a product, and it is the one the explainer pages leave out.
Sony put the encoder into the open Android source, so a handset maker can install the sending half for nothing. The receiving half is a different arrangement.
Sony’s own page is explicit about it. Installing the software still requires a licence from Sony, and the receiving product needs a licensed decoder.
In practice that means the codec arrives with the chip. Sony publishes the Bluetooth chip makers that carry its implementation, and the list is a who’s who of the Shenzhen audio supply chain.
Actions, AIROHA, Barrot, Bestechnic, Jieli, Bluetrum, Syncomm, Wuqi, Smartlink and Sunitec all appear as technical partners. If a product runs one of those parts, LDAC is available. If it does not, firmware will not fix it.
Then there is time. Sony states that concluding a licence generally takes several months, and that excludes the implementation period.
That single sentence has a consequence for a quotation. A supplier who says LDAC can be added to a finished design in a firmware update is describing something the licence does not allow.
Ask which chip. Ask for the licence holder’s name if the brand is not the licensee. Ask for the test report, since Sony names the measurement houses its partners use.
The certificate has its own arithmetic. The Japan Audio Society grants the wireless high-resolution mark, and Sony states the LDAC mark is satisfied at 990 kbps.
Six codecs held that mark as of mid 2024. LDAC is one, alongside LHDC, SCL6, LC3plus, SHDC and Qualcomm’s adaptive codec.
So the mark tells you the link can reach 990. It does not tell you the product will choose 990, and those are different promises.
What The Spec Sheet Means
Most of the confusion is a shorthand losing its condition. Here is the translation.
| What it says | What it means | What to ask |
|---|---|---|
| “Supports 990 kbps” | The codec has that step | What does it choose out of the box? |
| “Hi-Res Audio Wireless” | The mark is tied to 990 kbps | Who holds it, and at which tested rate? |
| “24-bit, 96 kHz” | The pipeline will accept that input | What is the source, and is it upsampled? |
| “3x the data” | Measured against 328 kbps | Which of the three rates is being compared? |
| “Lossless wireless” | Not possible at 990 against 1,411 | Ask them to explain how. |
| “Studio quality” | Nothing measurable | Ask for the test report instead. |
None of those lines has to be a lie. Each one drops a condition that the buyer then has to supply from memory.
Eight Lines For The Sheet
A supplier who can answer all eight has done the work. A supplier who answers five has a sample, not a product.
One. The rates supported, and whether the manual selection is exposed to the user or hidden in a service menu.
Two. The Bluetooth chip, by part number. That is the honest answer to “do you have LDAC”.
Three. The decoder licensee, if the brand is not Sony itself.
Four. The sample rates and bit depths accepted, with the manual options listed separately from the automatic ones.
Five. The default mode at first connection, stated plainly.
Six. The tested signal range, in dBm, at which the two highest rates hold without a drop-out.
Seven. The certificate and its holder, with the tested transfer rate written next to it.
Eight. The lab report, from a house that measures audio rather than a house that measures radios.
Those eight lines belong in the file even if the answers are unwelcome. A specification sheet a factory has to build against is what turns a codec name into a testable item.
Two lines sit outside the audio list. The choice between the two short-range radios sets the ceiling before any codec is chosen. And the version of the radio underneath decides how much of that ceiling is usable.
Ten Minutes With A Phone
You do not need a lab to see the gap. One phone, one headset and a familiar track will do it.
Force the highest rate. Open developer options on an Android phone and set the codec to LDAC at 990. Without that step you are testing the default, which is the point.
Listen for cymbals. Switch between 990 and 330 on a track you know. The difference shows up in cymbals and strings, not in bass.
Walk away. Put the phone in a pocket and take ten steps. Read the codec indicator. The rate will fall, and that is the number the customer will live with.
Compare with a cable. Plug in and listen again. The cable is the ceiling the codec is trying to reach.
Check the source. If the track came from a 256 kbps stream, the whole test measures the wrong thing.
Ten minutes of that tells you more than a page of claims, and it costs one sample.
Send me the specification sheet for a wireless audio product you are considering, or the quotation that claims LDAC. I will check the chip, the decoder licence, the rate the product actually defaults to, and which of the eight lines are missing. No cost, no obligation.
Check My SheetQuestions Buyers Ask
Is LDAC better than the default codec?
At 660 and 990, yes, and measurably so. At 330 the same test found it worse than the baseline codec above 15 kHz, which is the rate a pocket often produces.
Is LDAC lossless?
No. A CD is 1,411 kbps and the ceiling is 990, so about a third of the data is discarded. It is the closest thing a short-range link offers, which is not the same as lossless.
Does an iPhone support it?
No. Apple devices do not carry the codec, so they fall back to their own. A transmitter with the right driver can be added, but that is an accessory, not a feature of the phone.
Why does my phone show 660 instead of 990?
Because the default mode chooses the rate from the link, and most phones settle one step below the highest. Forcing 990 is possible on Android, through developer options.
Can it be added to a product by firmware update?
Not by firmware alone. The decoder is licensed, and the practical route is a Bluetooth chip that already carries a licensed implementation. Sony states the licence process takes months.
Does it work on a laptop?
Not natively on the common desktop systems. A transmitter that supports it, plus a driver from its maker, is the usual route, and the fallback is the codec the system already knows.
Questions & Comments
We read every one and reply within 24 hoursIf a quotation claims LDAC, send it over. I will check the chip, the decoder licence, and the rate the product actually picks on its own.