PVD Coating Jewelry: Which Pieces Fit, And What It Costs
PVD puts a hard film on metal inside a vacuum chamber. On jewelry the first question is not which colour, but which parts can be coated at all.
A plater can dip anything with a wire. A PVD shop has to hang the piece in a chamber and hope the vapour reaches every face.
That single difference decides your quote, your minimum order and your failure rate. This article works through it in the order a buyer meets it: shape, then substrate, then cost, then proof.
The Short Answer
PVD stands for physical vapour deposition. A solid coating material is turned into vapour in a vacuum, and it lands on the part as a thin film.
The film is thin. A peer-reviewed review of decorative PVD puts films anywhere from a few angstroms to several microns, laid down at 10 to 100 angstroms per second. Coating shops quote 2 to 5 microns on the working faces of a part.
So the film is not a plated layer, and it is not a filler. It copies the surface it lands on, scratch for scratch.
Three things decide whether a piece can wear it. First the shape, then the metal under it, then how clean the shop got that metal before the door closed.
Two conclusions follow, and both cost money if ignored. PVD is the right answer for a solid band, a watch case or a flat charm, where every face can see the target. It is the wrong answer for a fine chain or a filigree cage, where most of the surface sits in shadow.
The second conclusion is less comfortable. Much of what arrives labelled “PVD” on cheap fashion jewelry is electroplating with a new name. Section six shows how to tell.
Shape Decides Before Chemistry
Both common PVD methods, evaporation and sputtering, move material in a straight line. The review describes the path as line-of-sight for evaporation and “almost straight-line” for sputtering.
Vapour that travels in a straight line cannot turn a corner. A face that points away from the target, or sits behind another face, gets little or nothing.
The shop works around this by racking. Parts are fixed to a fixture and often rotated on several axes. Others ride a conveyor past the source, so each side gets its turn in the line of sight.
Rotation solves a flat band. It does not solve a chain, because each link shields the next one from the inside. It does not solve a blind hole, a deep channel or a hollow back.
This is why the same shop quotes a black band cheerfully and a black chain reluctantly. It is not a pricing mood. It is geometry.
Write the answer into the order as a face list. Name the faces that must be coated, and name the ones that may stay bare. A shop that has to guess will guess in its own favour.
| Part shape | Typical coverage | Why | What to do |
|---|---|---|---|
| Flat band, signet top | Full on the outer face | The face sees the target | Rack face-out, rotate |
| Watch case, bezel | Full on the visible planes | Shallow curves keep the line of sight | Mask the threads |
| Solid charm, tag | Full front, thin on the edges | Edge-on faces catch less vapour | Ask for an edge reading |
| Cuff, bangle | Outer yes, inner thin | The inner curve faces away | Declare the inner face cosmetic |
| Fine chain | Partial, link by link | Each link shades the next | Plate it, or accept a two-tone look |
| Filigree, lattice | Patchy | Crossing wires hide each other | Keep the finish bright, not black |
| Hollow back, deep channel | Bare at the bottom | Straight-line travel cannot enter | Expect corrosion there first |
| Threads, hinges, clasps | Bare or bridged | Faces close over each other | Mask, then assemble |
The Metal Under The Film
Fashion accessories are usually made from a copper alloy such as brass, or from steel. The review is explicit about that. Plating still does most of the work in the trade, and PVD sits beside it, not in place of it.
That sentence matters when a supplier offers “PVD instead of plating” as an upgrade. On brass and steel it can be, because the metal is dense and takes a polish. On zinc alloy it usually cannot.
Zinc alloy casting is porous and soft. A film two to five microns thick copies every pit it lands on, and it cannot close one. Worse, the film does not carry the corrosion duty on its own at that scale. A plated layer under it does.
So the honest chain on a zinc casting is three steps, not one: cast, plate, then PVD for the colour and the wear face. A supplier who quotes PVD on bare zinc is selling you a part that will pit and blush in a season.
Solder is the second trap. A hollow joint, or one that still holds flux, gives off gas when the chamber pumps down. The gas leaves a blister or a pinhole in the film, and the blister is where the finish lifts first.
The review’s own framing is the useful one here. Coating is one step in a chain that runs from mechanical prep, through cleaning, heating and etching, to coating, cooling and conditioning. The weakest link in that chain sets the quality of the whole job.
Which is why a quote that names only the compound tells you almost nothing. Ask for the prep steps in writing, and ask what the shop does about porosity before it racks the parts.
What The Film Cannot Do
Four jobs are outside its reach, and each one turns into a complaint later.
It cannot fill. A scratch, a sanding mark or a porous casting shows through, now in black or gold. The film is a copy, not a coat of paint.
It cannot replace the plated layer on a base metal. At two to five microns it adds wear resistance and colour, not a corrosion barrier. The layer underneath is still doing that work.
It cannot simply be made thicker. A thicker film builds stress, and stress is what makes a film flake at an edge. When a shop offers “extra thickness” as the fix for wear, the next question is what happens to adhesion.
It cannot be touched up. A plated part can go back into a bath. A coated part has to be stripped and run again, which costs close to a new run.
There is a fifth limit that belongs to the buyer rather than the film. PVD changes the colour of the surface but not the legal description of the metal. A coated brass ring is still a brass ring, and the listing has to say so.
The Cost Model: Per Run, Not Per Piece
A plating line charges for metal and time. A PVD chamber charges for a run.
Every run is the same sequence: pump the chamber down, heat the load, deposit for a set time, then cool before anyone opens the door. That sequence costs the same whether the rack holds fifty pieces or five hundred.
So the price per piece is the run price divided by the number of pieces on the rack. The fixture design decides that number, and the fixture is the part of the quote nobody asks about.
Three consequences follow, and they explain most of the quotes that look strange.
Small parts are cheap to coat, per piece. Two hundred little charms fill a rack quickly, so the run price is spread wide.
Bulky parts are expensive per piece. A wide bangle takes the space of twenty charms and still counts as one piece. Its per-piece cost can be ten times the charm’s, for the same film.
Every colour change costs a run. The target is swapped and the chamber is cycled again. An order split across four colours pays four times for the same total quantity.
This is where a minimum order quantity comes from. It is not a policy or a courtesy. It is the number of pieces that fills the chamber well enough for the shop to make its margin.
The buying move is therefore consolidation, not negotiation. Cut the colour list to two or three, share one run across sizes, and let the shop hold the parts until the rack is full. The savings come from the rack, not from the discount you argue for.
How To Tell PVD From Plating
Labels are cheap. Four checks are not, and any one of them will settle the question on a delivered carton.
Read the elements. A handheld XRF unit reports the elements in the top few microns. Titanium, zirconium or chromium on a brass part points to a nitride film. Black rhodium plating reports rhodium instead. This is a screen, not a certificate, but it is fast and it is hard to argue with.
Cut a section. A cross-section under a microscope shows the film and the plated layer as separate bands, with a visible interface between them. It also measures thickness where the claim was made, instead of where the shop chose to measure.
Watch how it fails. Plating wears through at high points and the base metal appears under it, with a soft edge where the layer thins out. A PVD film tends to lift in a patch, or along a masked line, once it starts.
Compare the price to plating. If a shop quotes PVD at or below the plating price for the same part, ask which process the piece will actually see. Vacuum time is not free.
Run the first two on a sample, and the last two on every batch. A check before the pallet leaves costs less than a return container.
Three Tests, Three Different Answers
Most coating disputes start with two people quoting different standards. The standards are not competing. Each one answers a separate question.
ISO 3160-2 covers watch cases and accessories with gold alloy coverings. It sets out how to determine fineness, thickness, corrosion resistance and adhesion. If your part is a gold-tone case or a coated band, this is the family of methods to name.
ISO 9227 is the salt spray test. It defines the artificial atmosphere, not the pass mark. The number that matters is the hours your order asks for, and the appearance the part must show at the end.
ASTM G99 is the pin-on-disk wear test. It measures wear rate and friction under a stated load, which is the closest thing to a laboratory version of daily wear.
| Test | What it proves | What it does not prove |
|---|---|---|
| ISO 3160-2 | Thickness, fineness, adhesion and corrosion on gold-alloy coverings | That the colour matches your sample |
| ISO 9227 salt spray | How long the surface survives a salt fog | How it wears in a pocket |
| ASTM G99 pin-on-disk | Wear rate under a set load | Adhesion, or coverage inside a recess |
| Retained-sample rub | That this batch looks and behaves like the one you approved | Anything about a shape the sample did not have |
A shop with no lab can still run the last row. Keep a coated reference piece sealed in a bag. Rub the new batch and the reference with the same cloth and pressure, then count the passes until the colour changes. It is crude, and it catches most drift.
Six Lines For The Order Sheet
A coating order that fits on one page gets followed. One that runs to four pages gets skimmed by the person who racks the parts.
One: the substrate. Name the alloy, not just “brass”. The film behaves differently on a leaded free-machining brass than on a casting alloy. The shop can only pick a prep line if it knows which one it has.
Two: the compound and the colour. Name the compound, then attach a physical colour reference. A photograph cannot settle a gold tone, because the same compound reads differently at two thicknesses.
Three: thickness and where it is measured. Give a range in microns and name the face. “Two to three microns on the top face” is a spec. “Two microns” invites a reading from the easiest spot on the part.
Four: the face list. Say which faces must be coated and which may stay bare. Threads, hinge knuckles and clasp seats are usually masked. Writing that down avoids an argument about a bare patch that was never going to coat.
Five: the test. Name one standard, the hours, and the sample size. One test with a number beats three tests with no number.
Six: racking and packing. Ask how the parts are fixtured, and require film-to-film contact to be avoided in the carton. Two coated faces rubbing in transit arrive looking like a wear test.
When PVD Is The Wrong Answer
Five cases where a good shop will tell you to plate instead, and you should believe it.
A fine chain. The inside of every link is in shadow, and the piece is mostly inside surface. Plating covers it because liquid reaches where vapour cannot.
High-volume fashion at a low price. The run cost does not shrink with the order. At a few hundred pieces the per-piece premium over plating is hard to carry.
A one-off sample. You will pay for a whole run to coat three pieces. Prototype in plating, then prove the colour on the production run.
Anything soldered after coating. Heat and flux destroy the film at the joint. Coat after assembly, or design the joint out.
A mirror polish on soft zinc. The pits are still there, and a glossy black film makes them easier to see, not harder.
In each case the correct answer is not a better coating. It is a different part design, or a different finish, decided before the mould is cut.
Questions Buyers Ask
Is PVD coating real gold?
Usually not. A decorative gold-tone film is a titanium or zirconium nitride, and it carries no gold at all. Some shops do sputter real gold onto a part, and they quote it as a precious metal job rather than a coating job.
Does PVD rub off like plating?
It fails differently. A plated layer thins and wears through at the high points. A PVD film holds its thickness until it lifts, then a patch goes at once. Neither is permanent, and both fail first where the part takes contact.
Can sterling silver be PVD coated?
Yes, the process works on most metals. The limit is the metal, not the film: silver dents and scratches under a film two microns thick. A coated silver piece is still sold as silver, and the 925 stamp does not change.
How thick is PVD on jewelry?
Coating shops quote 2 to 5 microns on the working faces of a part. Published work on decorative PVD describes films from a few angstroms up to several microns, so the number on your order has to name both the value and the face it was measured on.
Is PVD better than plating for a black finish?
On a solid band, a case or a flat tag, yes: the film is harder and the colour sits in the film rather than on it. On a chain, or on a part that has to hit a low price, plating still wins, because it reaches surfaces the vapour cannot.
Does PVD stop silver from tarnishing?
Only where the film is intact. Air cannot reach coated metal, so a fully covered face stays bright. A thin edge, a masked thread or the inside of a link is as exposed as it was before, and that is where the first dark spot appears.
For the process itself, the compounds and the colour chemistry, read how a PVD line is actually specified and quoted. For gold tones against plating, the gold colour matching notes go deeper. Start at the casting stage if the finish sits inside a wider build. a jewelry programme set up from the casting stage is easier to control than a finish bolted on at the end.
Put the six lines on the page the workshop signs, not on the email thread. The spec sheet that the plating shop countersigns is the version that survives a change of shift.
Send me the part drawing, the colour reference and the quantity per colour, and I will tell you whether the shape can be coated, which faces will come out bare, and how many pieces a run has to hold before the price per piece makes sense. That is settled before the mould, not after the first container.
Check My Part
Questions & Comments
We read every one and reply within 24 hoursA part drawing, a coating quote and a photo of the bare faces are enough. Post the three, and I will mark which line the quote has left out.