What Is Plated Jewelry: Reading The Base Metal Before The Finish
Plated jewelry is a base metal with a thin metal coat.
The coat carries the colour. The base carries the shape, the weight and most of the risk.
Almost every page on this topic explains the coat. Almost none explains the four words a supplier will print on the box, and what each one is legally allowed to mean.
That gap is worth money. A buyer who knows the numbers can read a quotation and see what is missing in about ten seconds.
The Short Answer
Plated jewelry is an article made of one metal and covered with another. The cover is applied in a bath, in a vacuum, or by bonding a sheet under pressure.
In trade language, the word plated describes the cover only. It says nothing about the metal underneath, and it says nothing about how thick the cover is.
In the United States, four labels carry legal meaning. They are set out in 16 CFR Part 23, the federal rules for jewelry and precious metals. Each label fixes a karat floor and a thickness or a weight ratio.
That is the part a buyer can hold a factory to. A karat stamp on a plated piece describes the coating, not the object.
So the honest reading of a plated ring is two sentences, not one. What covers it, and what it covers.
Four Words, Four Legal Numbers
Here is the table almost nobody publishes. Every figure below comes from the marking rules, not from a brand.
| What the label says | How the layer is applied | What the rules require | Base named? |
|---|---|---|---|
| Gold plated, gold electroplated | Electrolytic bath | 0.175 micron fine-gold equivalent, 10K or better | No |
| Heavy gold electroplate | Electrolytic bath | 2.5 microns fine-gold equivalent, 10K or better | No |
| Gold plated, rolled gold plate | Mechanical bond | At least 1/40 of the metal weight, 10K or better | No |
| Gold filled | Mechanical bond | At least 1/20 of the metal weight, 10K or better | No |
| Vermeil | Electrolytic over silver | 2.5 microns fine-gold equivalent, 10K or better | Yes, sterling silver |
Read the last column first. Four of the five labels place no requirement at all on the base metal. Only vermeil does, and it asks for sterling silver at 925 parts per thousand or better.
Now read column two again, because it hides a trap. The same words "gold plated" can be earned two ways. One is a bath, where the number is a thickness. The other is a sheet bonded to the base and rolled, where the number is a share of the weight.
That is why a quote saying "gold plated, 1/40" and a quote saying "gold plated, 0.175 micron" are not describing the same product. Both are legal. Neither is comparable without the unit.
The karat must sit immediately before the word, at equal prominence. So "18K gold plated" is a complete claim, and "gold plated" alone is not.
Why 0.175 Micron Is Not Your 0.175 Micron
The thickness in the rules is quoted as fine-gold equivalent, not as the physical depth of the layer. The difference matters more than it looks.
Footnote 31 of the same section gives the conversion in one line. One micron of 12 karat gold is equivalent to one half micron of 24 karat gold.
Run that rule forward and the numbers separate. A 12 karat layer needs 0.35 microns of metal to clear the 0.175 cut-off. An 18 karat layer needs about 0.23 microns.
At the heavy grade the gap widens. A 12 karat coating needs 5 microns of real depth to reach a 2.5 micron fine-gold equivalent. The same claim in 18 karat needs about 3.3 microns.
None of that is a loophole. It is how the rule was written, and it is fair. The problem is what a buyer does with the number. Two quotes at "0.175 micron" may hold a thin 18 karat layer and a thicker 12 karat one, and the figure looks the same.
So the only usable question is a pair. What karat, and what thickness of that karat. One figure alone cannot be compared with another.
Five Base Metals, Five Different Products
A factory quoting plated jewelry will usually offer one of five bases. They feel similar in the hand and behave nothing alike after six months of wear.
| Base | How the part is formed | What the coat lands on | The question it raises |
|---|---|---|---|
| Brass | Stamped, cast or machined | A copper and zinc alloy | What shows at the edge when the coat goes? |
| Copper | Stamped or cast | Soft, pure metal | Does it bend before the coat wears? |
| Stainless steel | Stamped or machined | A metal that already protects itself | Why plate it at all? |
| Zamak | Die cast | Zinc with about 4 percent aluminium | Is the shape cast, and how thin are the walls? |
| Sterling silver | Cast, stamped or hand-formed | At least 925 parts per thousand silver | Is the base itself worth keeping? |
Brass is the default for plated fashion pieces. It stamps and casts well, takes a bright coat, and holds detail. The trade-off is what appears at a worn edge, because the base is a different colour from the coat.
Copper is softer. It takes a coat beautifully and deforms easily, so a thin bangle in copper will change shape long before the plating fails.
Stainless steel is the odd one. It already carries its own protective oxide film, which is why a great deal of it is sold bare rather than plated. When it is plated, the base is not the weak point.
Zamak is a zinc alloy with a fixed 4 percent aluminium, plus small amounts of magnesium and copper. It is almost always die cast, so it makes complex shapes cheaply. The reference on zamak alloys notes that it takes electroplating and conversion coatings well. It also gives the casting standards: ASTM B86 for parts and B240 for ingot.
Sterling silver is the only base with a defined purity floor in the marking rules. It also happens to be the only base worth recovering when the piece is finished with.
Notice what the table does not contain. There is no column for price, because base metal cost moves weekly and a quotation is the only honest source. What the table does give you is the sentence to ask: which base, formed how.
The One Layer The Law Makes You Disclose
Nickel sits between the base and the gold on a large share of plated jewelry. It is hard, it takes a bright finish, and it lets a thin gold wash sit over it.
It is also the most common cause of contact allergy in jewelry. The nickel restriction in EU law puts the share of sensitive people in Western Europe and North America at roughly 10 percent.
The US marking rules already allow for that stack. Where a base metal such as nickel sits over the gold, and a thin gold wash sits over that, the label must say so.
That disclosure requirement is narrow, and the gap beside it is wide. The rules force a statement when a nickel layer is buried under a gold wash. They do not force the supplier to name the base metal at all.
So a carton can be fully legal and still tell you almost nothing. The one layer you are told about is the middle one, and the layer you most need to know is the bottom one.
In the European Union the numbers are separate from the labels. Items in direct and prolonged skin contact may release no more than 0.5 micrograms of nickel per square centimetre per week. Ear posts and other body piercing parts are held to 0.2.
| Item | Nickel release limit | What it covers |
|---|---|---|
| Ear posts and piercing parts | 0.2 µg/cm²/week | Parts that pass through skin |
| Other prolonged skin contact | 0.5 µg/cm²/week | Rings, bracelets, necklace clasps, watch backs |
Two test methods run together. EN 1811 measures release after a week in artificial sweat. EN 12472 simulates wear and corrosion first, which is closer to what a ring sees.
Which is why a clean result on a new sample proves less than a buyer expects. A coated piece that passes on day one can fail once the coat has thinned.
Where A Plated Piece Fails First
The rules already admit the problem. The definition of reasonable durability says thickness does not have to be uniform, because different parts of a surface are worn differently.
That single sentence is the most useful line in the whole document. It means the number on a quotation is not a promise about the thinnest point, and the thinnest point is what decides the return.
Five places go first, and they go first on almost every design.
The inner band of a ring. It touches skin and whatever the hand touches, all day, and it is usually the last surface a plater inspects.
Chain link contact points. Each link rubs two neighbours. On a fine chain the contact area is tiny, so the load per square millimetre is high.
Clasp edges and the spring tongue. A lobster clasp has sharp edges and a moving part. Both are hard to coat evenly.
Ear post threads and the notch. A threaded post is coated last and handled most.
The rim around a set stone. That rim is worked and polished after casting, so any coating on it started thin and was then sanded.
None of this is a lab result from a batch I handled. It is how a coating behaves on a shape. That is the reason to name the thinnest point, not an average.
Three Ways To Put Metal On Metal
There are three routes, and the label usually tells you which one was used once you know what to look for.
The bath. The part goes into a solution and a current deposits metal onto it. Thickness builds with time and current density, and recessed areas can be shadowed by the shape itself. This is the route behind the 0.175 micron and 2.5 micron figures.
The vacuum. Metal is vaporised and condenses onto the part. It gives a hard, thin layer with good colour control. Our note on PVD against electroplating covers how the two compare in wear, because that is a separate decision from this one.
The rolling mill. A sheet of gold alloy is bonded to the base under heat and pressure, then rolled thin. The layer is not deposited; it is part of the sheet. That is what the 1/40 and 1/20 weight ratios are measuring.
The commercial difference is large. A bath can add a fraction of a micron for very little money. A rolling mill starts with real gold across the whole sheet, so the metal cost is visible in the quote.
Both routes can legally print the words gold plated. That is exactly why the unit matters so much.
Five Lines For The Order Sheet
A quote that says plated jewelry is not orderable. Five lines make it orderable, and each one closes a specific hole.
- Base metal, and how the part is formed. Name the alloy and say stamped, cast or machined. Brass and zamak can look identical and quote very differently.
- The exact label you will print. Write the karat before the word, for example 18K gold plated. Decide now whether heavy is needed, because it is a different thickness tier.
- Thickness and karat together. Ask for microns of fine-gold equivalent and the karat used to reach it. One figure alone cannot be compared with another quote.
- Nickel. Ask whether a nickel layer sits under the gold. If it does, ask for the release result and say which limit applies to your item.
- Coverage at the thinnest point. List the surfaces you count as significant, then ask for the minimum thickness on the worst of them, not the average.
Line five is the one that changes behaviour, because it removes the average. A plater who has to report a minimum will usually adjust the rack or the current to protect the thin areas.
The whole block belongs on one page that travels with the enquiry. The spec sheet a plating factory prices from is the right home for it.
Four Checks Before A Bulk Order
Paper first, then the parts. Four checks cover most of the risk on a plated line.
1. Read the label against the table. The karat should sit immediately before the word, at equal prominence. If it does not, the label is incomplete whatever the product looks like.
2. Convert the thickness before you compare. Take the micron figure and the karat, then work out the fine-gold equivalent. Two quotes that both say 0.175 can be quite different layers.
3. Ask about the layer under the gold. If there is nickel, ask for the release result and check which of the two limits applies to your item. An ear post is not judged like a bracelet.
4. Look at the thinnest point under a loupe. A clasp edge, a post thread or the inside of a ring band. If the base colour is already showing on a new sample, the bulk order will be worse.
Keep one approved piece sealed with the spec sheet and the plating report. When the bulk order lands, compare against that piece rather than a fresh sample the factory sends later.
If the same order includes earrings, check the posts against their own line rather than the necklace line. The earring sourcing notes on posts and backs cover what changes when the part goes through skin.
What A Listing May And May Not Say
Most disputes in this category are not about the metal. They are about a sentence on a product page.
It may say 18K gold plated over brass, when the karat comes first and the coating meets the thickness for that word.
It may not say gold on its own for a plated piece. The word has to be qualified so a buyer understands the object is surface-plated.
It may not say vermeil unless the base is sterling silver and the gold reaches the 2.5 micron tier. Heavy plating on brass is not vermeil at any thickness.
It may not say gold filled unless the layer is at least 1/20 of the metal weight and was applied mechanically.
It has to disclose a nickel layer covered with a gold wash. That is the one stack the rules single out.
One more family of words is risky here. Claims such as corrosion proof or rust proof are addressed in the same part of the rules. That is a fair signal about which words get misused most on listings.
The wider picture on how a factory turns a claim into a repeatable process sits in the guide to sourcing metal jewelry from China. That page covers the factory side of the same order.
If a quotation says gold plated and stops there, the label is carrying the whole claim. Send me the quote and any plating report, and I will check the karat against the thickness, the base metal and the nickel layer. Where a line is missing, I will name what to add before you pay a deposit.
Send The QuoteQuestions Buyers Ask
Is plated jewelry real jewelry?
It is real metal with a real coating. What it is not is solid. The base carries the weight and the coating carries the colour, so the two have to be judged separately.
How long does plated jewelry last?
It depends on three things: the thickness, the karat and where the piece rubs. A thick coating on a pendant lasts far longer than the same coating on a ring band. Any single number of months is a guess.
Is plated jewelry safe to wear?
For most people, yes. The concern is nickel, and the risk is highest on ear posts and other parts that pass through skin. If a nickel layer is present, ask for the release result rather than relying on the word hypoallergenic.
Can plated jewelry be re-plated?
Often yes, and the base decides whether it is worth it. A brass or sterling piece can usually be stripped and plated again. A thin die casting may not survive the stripping step.
What is the difference between plated and gold filled?
How the layer was attached and how much of the weight it represents. Gold filled is bonded mechanically and must reach at least 1/20 of the metal weight. Plated can be a bath at a fraction of a micron.
Does plated jewelry turn your skin green?
What discolours skin is usually the base rather than the gold. Copper and copper alloys react with sweat and leave a mark. A thicker coating or a different base removes most of it.
Questions & Comments
We read every one and reply within 24 hoursA plated piece that stopped shining is the easiest claim to argue and the hardest to settle. Tell me the base metal, the karat on the label and the thickness if you have it, and the argument usually ends there.