LED Color Temperature: What Kelvin Does Not Say
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

LED Color Temperature: What the Kelvin Number Does and Does Not Say

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao
· Updated November 6, 2026 · 9 min read

A Kelvin number describes the tint of white light. It says nothing about brightness, nothing about quality, and nothing about how long the lamp lasts. Two lamps sold as 4000 K can still look different side by side. The number is the centre of an allowed region, and each lamp may sit anywhere inside it.

That last point is where most orders go wrong, and almost no consumer guide mentions it.

I have had a shipment rejected over a colour difference that both parties could see and neither could measure. The label said the same figure on both boxes.

This page covers what Kelvin actually measures and the scale the trade uses. Then why the same number looks different, and the six lines that settle it.

Three lit LED lamps on a warm beige surface casting warm, neutral and cool pools of light
Same lamp, three tints. The colour of the light is a choice, not a quality grade.

The Short Answer

Color temperature is a description of tint, written in kelvins. Lower numbers look warm and yellow. Higher numbers look cool and blue.

The scale runs from about 1,800 K at a candle flame to about 6,500 K for overcast daylight. Household lamps mostly sit between 2,700 K and 4,000 K.

Here is the part that surprises people. A 2,700 K lamp is called warm, and physically it is the cooler object. A 6,500 K lamp is called cool, and it corresponds to the far hotter black body. The words describe the feeling of the light, not the temperature of the lamp.

None of this measures brightness. For that you need lumens, and for the light on a surface you need lux. Those are separate measurements with separate numbers on the box.

Why Kelvin, and Why It Is a Guess for LEDs

The scale comes from physics. Heat an ideal object and it glows: dull red first, then orange, then yellow, then white, then bluish white. The temperature of that object is the colour temperature of the light it gives off.

An incandescent lamp is close to that ideal object. Its light is thermal radiation, so its colour temperature is essentially the temperature of its filament. Nothing is being estimated.

An LED is not a hot object. It makes light by moving electrons across a semiconductor junction. Its spectrum never follows a black body at all.

So for an LED the industry uses a substitute figure. It finds the black body whose colour most closely matches the lamp. That body’s temperature becomes the correlated color temperature, or CCT.

Correlated is the word that matters. The number is a nearest match, not an identity. Two lamps can share a CCT and still have different spectra. That is why one figure can render colours two ways.

The naming adds a second layer of confusion. Blue sits at the high end of the scale and red at the low end. That is the opposite of the everyday association, where red is hot.

A related trap is the word daylight. Sunlight above the atmosphere measures about 5,900 K, and the standard daylight reference sits at 6,500 K. Daylight itself ranges between about 5,500 K and 6,500 K through the day.

So a lamp labelled daylight has matched a colour, not a spectrum. Its output can read 6,500 K on a meter and still render colours quite differently from the sun.

The Scale the Trade Actually Uses

Nobody buys at 3,847 K. The market settled on a handful of named steps, and a quote will name one of them.

KelvinReferenceWhere it is ordered
1,850Candle flame, sunriseDecorative and hospitality lamps
2,400Standard incandescentLegacy replacement, vintage filament
2,700Soft white compact fluorescent and LEDLiving rooms, bedrooms, restaurants
3,000Warm whiteRetail, hotel corridors, residential
3,200Studio lampPhotographic and film work
4,000Neutral whiteOffices, workshops, task lighting
5,000Horizon daylight, tubular fluorescentInspection, machine vision, display
5,500 to 6,000Vertical daylight, electronic flashPhotography, colour critical work
6,500Overcast daylightDaylight LED, exterior and security

The practical rule is that the choice follows the room. Warmer light is used where people relax, and cooler light where people concentrate. Schools and offices lean cool for that reason.

One warning about the extremes. A 6,500 K lamp in a residential street creates more scattered blue light than a warmer one. Several cities now restrict it for that reason. A cool white lamp is not a better lamp; it is a different tool.

Colour bar of the Kelvin scale from 1800 to 6500 with reference sources marked
The scale is a description of tint. Nothing on it is higher quality than anything else.

Why Two 4000 K Lamps Disagree

Here is the mechanism behind the rejected shipment, and it is worth reading twice.

A labelled figure like 4000 K is not a point on a chart. It is the centre of a tolerance region. The standard that defines that region lets a lamp sit anywhere inside.

The unit of that tolerance is the MacAdam ellipse. It is the region on a colour chart that holds every colour the average eye cannot tell apart from the colour at its centre.

The size of one step is not a guess. MacAdam measured it: it is the spread of a trained observer’s colour matches. So one step covers roughly two thirds of what an observer would call a match.

Double the step and the region grows. A lamp binned to a wide step can sit at the very edge of the region. A lamp binned to a tight step sits near the middle. Both are labelled 4000 K.

SortWidth of the allowed regionWhat a buyer sees
1 stepOne step of measured colour spreadNothing. Every lamp sits inside what the eye calls the same white
2 to 3 stepsTwo or three times that radiusNothing in separate rooms, a slight edge difference on one wall
5 steps and widerFive times the radius or moreA visible difference between neighbouring fixtures

Put them side by side on a white wall and the difference is visible. Put them in two rooms and nobody notices. That is precisely why the argument is hard to settle after shipping.

This is also why a tolerance written in kelvin is a weak tolerance. Colour difference is better counted in mireds, the reciprocal of the temperature in millions.

The arithmetic shows why. Between 2,700 K and 3,000 K there are about 37 mireds of movement. Between 5,500 K and 5,800 K, the same 300 kelvin step, there are about 9.

So a tolerance of plus or minus 200 K means four times more visible change at the warm end. The same figure at the cool end is almost invisible. A supplier quoting one figure for both ends has not thought it through.

There is a second axis as well. A lamp can match the target figure and still sit off the line. That line is the pure black-body colour. Above the line the light looks greenish, below it looks pinkish. The trade measures that offset separately. It is the usual cause of a 4000 K lamp that customers call sickly.

Diagram of a tolerance ellipse around 4000 kelvin showing two lamps sold at the same nominal figure
Both of these are sold as 4000 K. They are not the same white.

For a buyer the conclusion is direct. A Kelvin number without a bin is half a spec. It names the centre of a region and says nothing about the size of that region.

Colour Drift: Binning, Age and Heat

Even a well-binned lamp moves after it leaves the factory, and the reasons are documented by the industry itself.

Colour-tunable LED systems are described as a difficult engineering problem. Binning, age and temperature drift all change the colour actually emitted. Feedback systems with colour sensors exist to correct for it.

Each of those three has a different signature. Binning decides where the lamp starts. Age moves the output as the phosphor and the chip degrade. The shift is not always the same across a batch. Heat moves it further. That is why one lamp drifts differently in a sealed fitting and in open air.

That is why a supplier can be honest about the sample and still fail the shipment. The sample was one bin; the shipment spans several.

Ask for the bin code on the reel and the colour shift allowed across the order. Those two answers turn a tint into a spec.

Dimming Moves the Colour

If the product has a dimmer, the colour question gets harder, and a fixed-CCT lamp is not a fixed-colour lamp.

Drive an LED at a lower current and its spectrum shifts. The tint moves as the light goes down. The industry treats this as a real engineering problem. The feedback systems that hold colour steady exist because of it.

Two product types answer it in different ways. A colour-stable product holds its labelled figure across the dimming range, using a sensor or a compensated driver. A dim-to-warm product does the opposite on purpose. It follows the curve of an old incandescent lamp, dropping to a warmer tint as it dims.

Both are legitimate. You cannot swap them. A buyer who orders one and expects the other will hear about it.

The line for the order is simple. State what the colour must be at full output, and again at ten percent. Then say whether the product may drift in between.

Six Lines for the Order

A Kelvin number on its own is half a spec. These six lines make it whole.

  1. Target figure and bin. Write the target kelvin figure and the bin step, for example 4000 K at three steps. The step is what tells the factory how tight to sort.
  2. Position on the second axis. State how far above or below the black-body line the light may sit. This is the tolerance that stops a greenish batch.
  3. Spread across the order. Name the bin code expected on the reel, and how much colour difference one shipment may contain. Sample-to-shipment drift is the usual failure.
  4. Colour rendering. Give the rendering index and the acceptable bin. Tint and rendering are separate properties. A lamp can be right on one and poor on the other.
  5. Behaviour under dimming. State the colour required at full output and at ten percent, and whether the product is meant to be dim-to-warm.
  6. Test condition. Name the instrument, the drive current and the case temperature the measurement was taken at. A colour figure without a condition cannot be repeated.

Line one is the one that prevents the rejected container. A drawing that says “4000 K” tells a factory what the centre should be. It leaves the factory free to ship from anywhere inside the region.

Light bars show the effect clearly, because the eye compares segments that sit next to each other. The light bar build notes cover how colour consistency is held along a run.

How to Compare Two Quotes

Three checks separate a real quote from a label.

First, look for the bin step next to the kelvin figure. If the quote only says 4000 K, the tolerance is undefined. The cheaper supplier then wins by sorting less.

Second, ask for the second axis figure. A quote that names only the kelvin value says nothing about the green or pink direction. That offset is what customers describe as an ugly light.

Third, ask what the colour does at ten percent output. If the answer is “it dims”, the product is a fixed-CCT lamp with an unstated colour shift.

When a container arrives, the check is cheap. Put one lamp from each carton against a sheet of white paper under the same lamp, and look along the row. Colour differences that a meter reports are usually visible this way too.

Do it in a dark room with no daylight, because window light hides a warm or green cast. If the row looks uneven, the bin spread is wider than the order allowed.

After those three, price and warranty belong in the conversation. A lamp that meets the figure in the sample and drifts across the order has a lower price for a reason.

For a work light, the colour figure matters more than buyers expect. The task is judging material. The work light specification usually names both the tint and the rendering target for that reason.

For anything outdoor, the tint is also a planning question. The street lighting specification has to satisfy a resident and a council at once. The kelvin figure is where those two interests meet.

Whichever product it is, the colour claim ends up in the same place as every other claim. The photometric test report is where a tint that was agreed in a message either survives or does not.

THE BIN LINE

A Kelvin Number Needs a Bin Beside It

Send me the kelvin figure, the rendering target and whether the product dims. I will tell you which bin step the order needs. I will also point out where the drawing is silent in a way a factory will fill in for you, and what to write so the second container matches the first. That costs nothing before tooling.

Send the Colour Spec
Is 4000 K brighter than 2700 K?

No. Kelvin describes tint. Brightness is measured in lumens, and the light reaching a surface is measured in lux. A 2,700 K lamp and a 4,000 K lamp can have identical output.

What does 3000 K look like?

Warm white with a slight yellow cast, close to an old soft-white bulb. It is the common choice for retail, hotel corridors and homes where the light is meant to feel calm.

Why do two 4000 K bulbs look different?

Because 4000 K is the centre of a tolerance region. Each lamp may sit anywhere inside it. The size of that region is set by the bin step. Age and heat add further drift after installation.

What is a MacAdam step?

It is the measured spread of a trained observer’s colour matches. The chart draws that as an ellipse. A smaller number of steps means a tighter sort and a more consistent batch.

What does dim-to-warm mean?

A product that drops to a warmer tint on purpose as it dims, copying how an incandescent lamp behaved. A colour-stable product does the opposite and holds its figure across the range.

Can I mix colour temperatures in one room?

Not within one continuous run of fixtures, because the eye compares neighbours. Different zones can differ on purpose, such as a warm seating area beside a cooler work area.

Questions & Comments

We read every one and reply within 24 hours

A kelvin figure names the tint and leaves the tolerance open. Tell me where the product is installed, and I will say how tight the colour sort has to be before you commit.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x