What Is Stainless Steel Jewelry: 304 And 316L At The Factory
Stainless steel jewelry is made from a steel alloy with chromium and nickel in it, usually grade 304 or grade 316L. The chromium forms a thin oxide skin that stops rust, and the nickel keeps the metal workable.
The grade matters more than the word. Two rings sold as stainless steel can carry different chromium levels, different nickel levels, and different answers to salt water.
This page covers the two grades, the carbon number behind the letter L, the magnet test, and the six lines an order needs.
The Short Answer
Both common jewelry grades are austenitic stainless steels. That word means the metal keeps one crystal structure at room temperature, and it brings two useful results.
First, the surface stays bright because chromium oxide re-forms when it is scratched. Second, the alloy is not magnetic, which is where a popular test goes wrong.
Grade 304 is the cheaper option and the most common stainless steel in the world. Grade 316L is the marine and medical grade, with molybdenum added.
Neither grade contains gold, silver or platinum. A steel ring sells as a base-metal product, and a gold-coloured steel ring carries a coating on top.
What The Two Grades Actually Are
The numbers are published in the standards, and they are narrow enough to check on a mill certificate. This is the published 304 chemistry from ASTM A276.
| Element | 304 | 316L | What it does |
|---|---|---|---|
| Chromium | 18.0–20.0 % | 16.0–18.0 % | Builds the oxide skin that stops rust |
| Nickel | 8.0–11.0 % | 10.0–12.0 % | Holds the austenitic structure and the shine |
| Molybdenum | None | 2.0–3.0 % | Resists chloride pitting |
| Carbon | 0.08 % max | 0.035 % max | Lower carbon means less weld and heat damage |
| Manganese | 2.00 % max | Up to 2 % | Cheap substitute for part of the nickel |
The pattern is clear once the table is in front of you. 304 carries slightly more chromium, 316L carries less chromium and adds molybdenum.
Molybdenum is the expensive line. It is what makes 316L the grade chosen for marine fittings, chemical plant, food equipment and watch cases.
Both grades sit near 7,900 kilograms per cubic metre. A steel ring therefore weighs about the same as a sterling ring of the same size, and more than a gold one.
The melting range is about 1,400 to 1,450 degrees Celsius for 304. That is far above any soldering or plating step in a jewelry workshop.
Where the two grades really part company is chloride. 304 is prone to pitting and crevice corrosion in warm chloride conditions, and to stress cracking above about 60 degrees Celsius.
Chloride is not an industrial word only. It is in seawater, in swimming pools, in some cleaning fluids, and in sweat.
316L resists local attack by chlorides better because of the molybdenum. That is the whole reason a coastal market pays more for it.
What The Letter L Buys You
L stands for low carbon. Grade 304 allows up to 0.08 percent carbon, and 316L allows up to 0.035 percent.
That small gap matters at temperature. Between roughly 480 and 820 degrees Celsius, carbon and chromium combine at the grain boundaries and form chromium carbides.
The grains then lose chromium at their edges, and the metal can corrode along those edges while the rest stays bright. The trade name for that is sensitisation.
A jewelry part rarely reaches that range in service. It can reach it during welding, during some soldering setups, and during heat treatment in a plating line.
So the L grade is insurance for any part that gets hot on the way to being finished. For a plain stamped pendant it changes little.
Be careful with the naming. A factory quote for 316 is not the same as 316L, and the price gap is real because the carbon range is tighter.
Ask for the grade on the mill certificate, then check the carbon figure against the row above.
The Magnet Test, And Why It Proves Little
A magnet is the test every buyer tries first, and it answers the wrong question. Austenitic grades are not magnetic, so 304 and 316L both fail to attract.
A magnetic ring is therefore not steel of either grade, and that part of the test is useful. It screens out cheap ferritic steel.
The problem is the other direction. A non-magnetic ring proves only that the metal is austenitic, and several alloys share that property.
Grade 201 is austenitic too, and it substitutes manganese for part of the nickel. It passes the magnet test and costs less.
That substitution is the most common grade swap in the trade. A buyer orders 304, receives 201, and finds rust spots after a few months of wear.
Chemistry is the only answer. Ask for the mill certificate, then check chromium, nickel and manganese against the alloy tolerance.
A handheld alloy analyser reads the surface in seconds and costs little per lot. For a repeat program it is cheaper than one returned container.
Nickel, Skin And The Word Hypoallergenic
Both grades carry nickel, at 8 to 11 percent in 304 and 10 to 12 percent in 316L. Nothing in the alloy chemistry removes it.
Nickel is the most common metal allergy, so a nickel-sensitive wearer can react to steel as easily as to plated brass.
Some markets restrict nickel release from items worn against the skin all day. Where that rule applies, the release figure has to be tested, not assumed.
That is why the word hypoallergenic is weak evidence. It describes a hope, and it names no grade, no coating and no test.
A useful answer names three things. The grade, the coating, and the release test with its method.
For a piercing stud the question is sharper than for a pendant, because the post sits in an open wound and stays there.
Buyers who sell into a market with a nickel rule should treat steel earrings as a test item, not as a safe default.
Gold Colour On Steel Is A Coating
A gold-coloured steel ring is steel with a layer on top. The layer is usually titanium nitride applied by physical vapour deposition, or a thin gold plate.
PVD gives a hard, thin film in gold, rose and black tones. It wears at the high points of a ring, and it cannot be repaired in a shop.
| Product | Body metal | Colour layer | What wears first |
|---|---|---|---|
| Solid 14K gold | Gold alloy | None | Nothing except polish |
| Gold plated steel | Steel | Gold electroplate | The plate, then the steel shows through |
| PVD steel | Steel | TiN film | The film at edges and contact faces |
The labelling duty follows the body metal. A plated steel ring is a steel ring and has to say so, which is the same principle that governs plated brass.
The guide to plated jewelry covers how those layers are described on a tag.
Thickness is the number that decides life. Ask for the coating thickness in microns and the wear test behind it, not for a colour sample.
A ring worn daily and a pendant touched once a week need different answers. One coating will not serve both.
If the customer wants a colour that lasts years, the honest choice is a solid gold alloy. One example is the 58.3 percent alloy, not a coated steel.
Sizing, Clasps And What Fails First
Steel outlasts most of what is attached to it. The part that fails first is usually the clasp, the jump ring or the plating edge.
Start with size. A steel ring cannot be resized the way a gold ring can, because the metal is hard and the shank is thin.
A jeweller can stretch a plain band by a size or two on a mandrel, and that is the limit. A patterned or stone-set steel ring is bought to size or not bought at all.
So the size range belongs on the order, not in the shop later. Ask for the full run of sizes, the step between them, and the tolerance on the diameter.
Chain length is the same argument. A steel chain is sold in fixed lengths, and adding length means a new clasp or a second chain.
Now the clasp. A lobster claw in steel is strong, and a cheap spring ring is not, so the clasp type is a price line worth reading twice.
Ask for a pull test on a finished piece. Hang a known weight from the clasp and hold it, then repeat on ten pieces.
The jump ring is the second weak point. A ring that is not soldered can open under load, and a soldered one cannot be adjusted later.
Plating fails at edges and at contact faces. A ring wears at the palm side first, a necklace at the point where the chain meets the pendant.
That is why the coating thickness is quoted per face and not as one number. Thin coverage on an edge shows through in weeks.
Polishing is the cheaper repair. Steel takes a mirror polish again, and the oxide skin re-forms after it is cut back.
Keep the polish off the coating, though. A polishing wheel will strip a thin PVD film faster than wear will.
So the wear story is short. Steel holds, the clasp and the coating do not, and both are decided on the order sheet.
What The Quote Should Separate
Steel jewelry is priced by weight plus process, and the process is where the money hides. Three lines belong on every quote.
The first is the grade, written as 304 or 316L with the standard it meets. A quote that says stainless steel has said nothing yet.
The second is the coating, with its type and thickness. The third is the finish, because a mirror polish costs more labour than a brushed one.
Grade substitution is the risk to price for. 201 can pass a magnet test and a visual check, and it saves money at the mill.
The check that settles it is chemistry, on the certificate or on the part. Either way it happens before the cartons are sealed.
Weighing helps too. Steel is dense, so a light steel chain is a thin chain. A thin chain fails at the clasp before it fails at the link.
If the piece carries stones, the setting matters more than the grade. Steel is hard, and a hard metal grips a stone differently from a soft one.
Six Lines For The Order Sheet
Six lines close most steel arguments. They fit on one page and they travel with the carton.
One, the grade and the standard. 304 or 316L, with the chemistry range and the certificate expected on each lot.
Two, the chemistry check. Name the elements tested and the method, and say what happens if a lot misses.
Three, the coating. Type, thickness in microns, and which surfaces are coated. Note that edges take less coating than flats.
Four, the finish. Mirror, brushed or sandblast, with the surface roughness that defines each one.
Five, the weight tolerance. A range in grams per piece, checked on a sample from the first carton.
Six, the marking. What goes on the tag: the body metal, the coating, and the country of origin.
Two habits keep the sheet honest. Photograph the stamp or the tag on the first approved piece, and keep that piece sealed for comparison.
Then test one lot in the middle of the run, not only the first. Grade drift shows up in the middle of a busy month.
The one-page spec a Chinese factory works from is where these six lines belong. The same sheet should carry the silver grade reference if the program mixes metals.
For a chain program, add the link spec, the clasp type and the pull test. The Cuban link breakdown shows how much of the cost sits in the link, not the metal.
Book the check before the bulk run. An inspection before the lot ships can read a certificate and pull a sample for alloy testing.
Send The Cert
Send the mill certificate or the spec line you were given for a steel program. I will read the chromium, nickel and carbon figures against the grade you ordered. You also get the two tests to run before the cartons leave, and the line to add to the spec sheet.
Send The CertQuestions Buyers Ask
Is 316L better than 304 for jewelry?
It is better where chloride is present, because molybdenum resists pitting. For a pendant sold in a dry market, 304 is usually enough.
Will stainless steel jewelry turn my skin green?
Steel itself does not leave a green mark. A copper or brass layer under a thin plate can, which is why the body metal belongs on the tag.
Is stainless steel jewelry magnetic?
Austenitic grades are not magnetic, so 304 and 316L both fail a magnet test. A magnet therefore cannot tell the two apart.
Does stainless steel jewelry rust?
It can pit in warm chloride, which means sea water, pool water and some sweat. 316L resists that better than 304.
Is stainless steel hypoallergenic?
No grade earns that label by chemistry. Both grades carry nickel, so a nickel-sensitive wearer needs a release test rather than a word.
How long does gold coloured steel last?
It depends on the coating thickness and the wear. A PVD film on a pendant lasts longer than the same film on a ring worn daily.
Questions & Comments
We read every one and reply within 24 hoursIf a steel quote is open on your desk, send the grade and the certificate behind it. I will read the chemistry against the standard it claims.