What Is 14K Gold? Karat, Alloy, And Metal Cost
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is 14K Gold: The 58.3 Percent Behind The Mark

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao
· Updated November 16, 2026 · 11 min read

14K gold is an alloy with 58.3 percent gold and 41.7 percent other metals. The 14 means 14 parts of gold out of 24, and the other ten parts are what give the metal its colour and its strength.

That split is the whole story for a buyer. It sets the metal cost, the colour, the hardness, and the words that may go on the tag.

This page covers the karat arithmetic, the alloy behind each colour, the marking rules, and the six lines for an order.

Yellow gold ring and chain on a warm beige studio surface beside a small jeweller's loupe
Two pieces, one stamp. The colour and the price both come from the same 41.7 percent.

The Short Answer

Karat is a fraction with 24 on the bottom. Fine gold is 24 karat by definition, so a 14 karat alloy is 14 divided by 24.

That comes to 0.583, or 58.3 percent. The same figure appears on a stamp as 585, meaning 585 parts per thousand.

The remaining 41.7 percent is not filler. It is a mix of silver, copper and zinc, and the recipe decides almost everything a customer notices.

Change the copper and silver ratio and the metal turns from pale yellow to warm yellow. Add palladium or nickel and it turns white. Push copper higher and it turns rose.

So 14K is a family, not a single material. Two rings with the same stamp can differ in colour, hardness and price per gram.

Karat Arithmetic, And What Else It Buys

Higher karat means more gold. It also means a softer metal, because gold itself is soft and the alloy is what carries the strength.

MarkGold shareParts per thousandWhat it is used for
24K99.9 % and up999Coins and bars, not stone settings
18K75.0 %750Fine jewellery, softer prongs
14K58.3 %585Daily-wear rings, chains, settings
10K41.7 %417Budget pieces, US minimum for the word gold
9K37.5 %375UK and Commonwealth market

The table explains a trade-off that buyers meet on every quote. Going from 14K to 18K adds about 16.7 points of gold, and it adds cost in a straight line.

On a 5 gram ring the gold content rises from about 2.9 grams to 3.75 grams. The money follows the gold, and the labour barely moves.

The strength moves the other way. A 14K prong holds a stone better than an 18K prong of the same shape, because the harder alloy resists bending.

That is why 14K sits where it does in the market. It carries enough gold to be sold as gold, and enough alloy to survive daily wear.

Bar chart comparing gold content of 24, 18, 14 and 10 karat alloys
Four marks on one scale. The gap between 14K and 18K is 16.7 points of gold.

What The Other 41.7 Percent Is Doing

Three families of recipe cover most of the trade. Each one is a colour decision first and a cost decision second.

ColourAlloy metalsWhat to watch
YellowSilver and copper, with a little zincCheapest to make, colour drifts with the copper ratio
WhitePalladium or nickel, plus silverRhodium plating hides the true colour and wears off
RoseMore copper, less silverCopper-rich mixes run harder and darker

The numbers behind those colours come from published alloy recipes, not trade secrets. An 18K rose alloy runs 75 percent gold, 22.25 percent copper and 2.75 percent silver.

An 18K red alloy drops the silver and takes 25 percent copper. A 14K red alloy used in the Middle East carries 41.67 percent copper.

Zinc is the quiet fourth metal. Up to 15 percent can go into a copper-rich mix to push the colour from red towards yellow.

Panel showing yellow, white and rose 14 karat alloys and the metals that create each colour
The same 58.3 percent gold, three recipes, three colours.

White gold is the one that needs a warning. The alloy is a pale grey-white, not the bright white a customer sees in a shop window.

The bright white comes from rhodium plating. That plating is a separate layer, and it wears at the high points of a ring within months of daily wear.

A buyer who orders white 14K without agreeing a re-plating plan has sold a finish, not a metal. Put the plating thickness and the re-polish interval on the order.

How A 14K Piece Gets Tested

Four methods settle a karat question in the trade, and they do not agree with each other. Knowing which one produced a number decides how much that number is worth.

MethodWhat it readsCost of the test
Acid and touchstoneThe surface, judged by streak colourQuick, needs a bench jeweller
X-ray fluorescenceThe outer layer only, in secondsNo damage, needs a machine
Fire assayThe whole sample, after meltingThe sample is destroyed
DensityWeight against volume, so the alloy as a wholeNo damage, needs a known recipe

The acid test is the oldest and the least precise. A jeweller rubs the piece on a stone and applies acids of known strength until the streak stops reacting.

X-ray fluorescence is the machine most factories use for incoming metal. It is fast and it does not mark the piece, and it only sees a thin layer at the surface.

That layer is where plating sits. A rhodium layer on white gold is not gold at all. A plated brass piece can also read close to a real alloy on a cheap setting.

Fire assay is the referee. A small sample is melted with fluxes and the gold is weighed after separation. A refiner’s report therefore carries more weight than a shop reading.

Density is the quiet check. Weigh the piece in air and in water, and the ratio tells you the alloy’s average density, which a plated skin barely moves.

So the question to ask is short. Which method produced the number, on which date, and was the sample taken before or after plating?

A supplier who answers all three is running a real quality system. A certificate that names no method is decoration.

The Words That May Go On The Tag

The marking rules are short, and they are the part most factory labels get wrong. Three examples in the federal guide cover the common errors.

First, the word gold on its own. It may only describe a product that is fine gold throughout, which means 24 karat.

Second, an alloy. The karat figure has to come immediately before the word gold, and it has to be at least as easy to see.

Third, plating. If the surface is plated or coated, the label has to say so. A plated brass ring marked 14K gold is a mislabel, not a shortcut.

Mark on the tagVerdictReason
14K GOLDCorrectKarat figure sits next to the word gold
585Correct as a fineness mark585 parts per thousand equals 14 karat
GOLDWrong on a 14K pieceUnqualified gold means 24 karat
GOLD PLATED 14KOnly with a plating disclosureThe base metal has to be named
14K GOLD FILLEDDifferent productFilled and plated are separate categories

A mark also has to be honest about where it applies. If the stamp covers only part of an item, that limit has to be disclosed when the location misleads.

Legibility counts. A stamp too small to read at normal vision does not do the job, and neither does a mark that hides inside a shank.

The same section points at the National Stamping Act. A maker or importer that applies a quality mark also carries an identity duty, so a maker’s mark belongs beside the karat.

Read the guide text itself before you approve artwork. It runs to about 25 pages and the marking sections are three of them.

Parts That Do Not Have To Be Gold

A 14K piece is not 14K all the way through. The guide lets certain small parts drop out of the assay, and the list is worth knowing before you promise a spec.

Springs, posts and the separable backs of lapel buttons are exempt. So are bracelet and necklace snap tongues, and posts and nuts for interchangeable ornaments.

The practical meaning is simple. A 14K hoop can carry a non-gold post and still be sold as 14K, as long as the marking is applied honestly.

That is where importers get caught. A retailer reads “14K” and tests the whole piece, then finds a plated post and treats it as a false claim.

Decide the answer on the order. Either every part is 14K, or the exempt parts are named in writing with their own metal.

The Cost Of A Gram

Metal cost is arithmetic, and it is the part of a quote that moves every day. The rest of the quote does not.

Start with the spot price for one troy ounce of gold. Divide by 31.1035 to get the price of one gram of fine gold.

Multiply by 0.583 for a 14K piece, then by the weight. A 5 gram ring holds 2.9 grams of fine gold, and that is the part that swings with the market.

Take a spot price of 2,000 dollars an ounce and the figure is about 64 dollars a gram of fine gold. The same ring would carry about 187 dollars of metal.

Those numbers are an illustration, not a quote. The arithmetic is the same at any price, and the price you use has to be the one on the day.

Everything else sits outside that line. Alloy metals cost little, but casting, filing, setting, polishing and rhodium plating are labour and they hold their price.

So a quote needs two halves. State the metal basis with a date and a validity window, then price the labour separately.

A supplier who quotes one lump sum for a year has either hedged the metal or plans to deliver a lighter piece. Ask which.

The jewellery factory guide on this site covers the labour side of that quote in more detail.

Tarnish, Sweat And The 10K Line

Gold alloys of 10 karat and above may be described as corrosion resistant in the federal guide. That covers 14K, and it is a useful line to hold.

It does not mean the piece never dulls. Skin oils, perfume and chlorine attack the alloy metals at the surface, and the shine fades before the metal fails.

Hardness helps elsewhere. A 14K setting resists deformation better than an 18K one, which is why daily-wear rings sit at this karat rather than higher.

The exception is the white alloy. A nickel-white 14K piece can release nickel at the skin, and some markets limit that release for items worn all day.

Where that limit applies, a palladium-white alloy takes the question away. It costs more per gram and it removes a test the piece might fail.

The rest is care advice, and it belongs on the card. Remove the piece for swimming, keep perfume off the metal, and store it dry.

Six Lines For The Order Sheet

Most disputes on gold jewellery come from one missing word. These six lines close the gaps.

One, the karat and the tolerances. Write 14K, then the accepted range for gold content on the finished piece, and the assay method that will settle it.

Two, the colour recipe. Yellow, white or rose is not enough. Name the alloy family so a repeat order comes back the same shade.

Three, the plating. For white gold, state rhodium thickness and which parts are plated. An unplated white piece will not match the sample.

Four, the non-gold parts. List every part that is exempt from the assay, with its own metal. Silence here becomes a claim later.

Five, the metal basis. Fix the spot price source, the date, and the validity window. Then the weight and the labour rate are the only open items.

Six, the marking. Give the exact stamp, the maker’s mark and where both go. Approve a photograph of the stamp before bulk.

Checklist card showing six order sheet lines for 14 karat gold jewellery
Six lines, and each one closes a gap that a karat stamp alone leaves open.

Two habits make the sheet hold. Weigh ten pieces from the first lot and record the spread, because cast weights drift by a few hundredths of a gram.

Then keep one approved piece in a sealed bag. Colour arguments are settled by comparison, not by memory.

The the single sheet the factory works from is where all six lines belong. It travels to the caster, the setter and the plater without being retyped.

Book the check before the bulk run. A booked inspection before the lot ships can weigh and test a gold lot, and a photograph cannot.

Choosing the factory is the earlier decision. A first-pass supplier screen removes the traders before you spend a month on samples.

METAL BASIS

Send The Quote

Send the quote you were given, with the weight, the karat and the spot price it used. I will check the metal line against the weight, and flag any part that is exempt from the assay. You also get the clause to add before you order.

Send The Quote

Questions Buyers Ask

Is 14K gold real gold?

Yes. It holds 58.3 percent gold by weight, which is 14 parts out of 24. The rest is silver, copper, zinc or a white metal.

What does 585 mean on a ring?

585 parts per thousand of gold, which is the same as 14 karat. Both marks describe the same alloy.

Is 14K better than 18K?

Neither is better in general. 18K holds more gold and costs more, and 14K is harder, so it suits daily-wear rings and stone settings.

Why does white 14K gold turn yellow?

The white alloy is pale grey, not bright white. The bright surface is rhodium plating, and it wears through at the high points with daily wear.

Can a 14K piece contain other metals?

Yes, on small parts. Springs, posts and snap tongues are exempt from the assay, so they must be named in the spec rather than assumed.

How is the metal cost worked out?

Spot price per troy ounce, divided by 31.1035, multiplied by 0.583, then by the weight in grams. Labour and plating sit outside that line.

Questions & Comments

We read every one and reply within 24 hours

If a gold quote is on your desk, send the weight and the karat with it. I will check the metal line against the weight and name the parts that are exempt from the assay.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x