Silica Gel: A Porous Bag That Holds Water
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Silica Gel: A Bag Of Pores That Holds Water

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 11, 2026 · 12 min read

Silica gel is a porous form of silicon dioxide that holds water on the inside surface of its pores.

It is the same chemistry as sand and quartz, made in a different shape. The shape is the whole point.

A single gram carries a surface of about 750 to 800 square metres. That surface is where water collects.

Two things follow, and they explain most of the questions people search for. The beads stay dry to the touch even when they are full, so a spent bag looks exactly like a fresh one. And the packet is not food, which is why it carries a warning.

This article covers what the bead is, how to size a bag or a container, and what the warning actually means.

Studio still life of clear silica gel beads spilling from a small paper sachet on a beige surface
Clear beads, porous inside, dry to the touch when full.

The Answer In One Line

An amorphous, porous form of silicon dioxide, made by acidifying sodium silicate into a gel, washing it, and drying it.

The drying step leaves a rigid network of silicon and oxygen, with tiny voids. The gel is hard and slightly translucent, softer than quartz, and it stays hard when saturated.

Water does not soak into the solid. It clings to the walls of the pores, then condenses in the narrowest ones.

That is why the trade says the bead is spent when it is full, not when it is wet. The outside gives no signal at all.

How A Bead Holds Water

The numbers here are small and worth remembering. A typical desiccant gel has pores around 2.4 nanometres across.

Small pores mean a huge internal area. That area is measured as specific surface. The reference figure is 750 to 800 square metres per gram.

Adsorption is a surface event. Water molecules stick to the pore walls. The bead can then look and feel unchanged while carrying a fifth of its weight in water.

How much it can carry depends on the humidity around it. At 77 °F, one supplier’s table gives roughly 10 percent of its own weight at 20 percent relative humidity. At 50 percent it gives 26, and at 75 percent it gives 34.

The reference page puts the top figure at 37 percent in high humidity. The two agree closely enough for design work.

Heat reverses it. Water leaves at about 120 °C, held for one to two hours, and the gel works again with little loss.

In practice a factory dries it hotter and longer. The range is 105 to 130 °C for four to six hours, in an electric oven with the door vented. Never a microwave, and never a gas oven.

Sachets are a different case. The paper or non-woven wrap and the glue set the limit. One maker caps the packet at 80 °C, and another sells it as single use.

Bar chart comparing water held as a share of own weight for silica gel, clay, molecular sieve and calcium chloride at three humidity levels
Same job, four curves: capacity by humidity, not by weight bought.

Four Drying Agents On One Shelf

Silica gel is the default, not the only option. The four below share a shelf and behave differently as humidity rises.

AgentWater held at 77 °F, 20 / 50 / 75 % RHWhere it fits
Silica gel10 / 26 / 34 % of its weightElectronics, leather, food-grade sachets
Clay (bentonite)11 / 19 / 25 %General cartons; best below about 49 °C
Molecular sieve18 / 20.5 / 22 %Products that must stay very dry
Calcium chlorideUp to 360 % at 80 % RHContainer loads and long ocean moves

The shape of each curve decides the choice. Silica gel wins in the middle and upper range, which is where most shipping sits.

Clay holds slightly more than silica gel at very low humidity, then loses ground. It also gives up capacity in heat, so a hot container is the wrong place for it.

Molecular sieve is nearly flat. That is its advantage. It keeps working when the air is already dry, which matters for a product with a moisture limit rather than a wish to be dry.

Calcium chloride is a different animal. It keeps taking water as humidity climbs, and it can turn to liquid as it does. That is why it ships in pouches for containers rather than small sachets.

The capacity table by relative humidity is where those figures come from, and it is worth keeping a copy.

One more distinction belongs here. A desiccant removes water. An oxygen absorber removes oxygen with iron powder. They are not substitutes and should not share a container.

How Much You Need

Desiccant is sold in units, not grams, and the unit is defined by what it holds.

One unit adsorbs at least 3 grams of water vapour at 20 percent relative humidity, and 6 grams at 40 percent, measured at 77 °F. That is the MIL-D-3464 definition.

The mass behind a unit is a conversion, not a definition. One supplier’s table puts it at about 26 grams of silica gel. Another puts it at about 33 grams at 25 °C.

Both are in circulation, and that is the first thing to settle with a supplier. Size in units, convert to grams only after the unit basis is agreed.

One rule is fixed: a single unit must not weigh more than 50 grams. A packet heavier than that is more than one unit whatever the label says.

The count comes from two formulas, both from the US military packaging standard MIL-STD-2073.

For a sealed barrier bag: units = 0.011 times the bag area in square inches, plus an allowance for what is inside.

For a rigid sealed container: units = 0.0007 times the internal volume in cubic inches, plus the same allowance.

The allowance is where most quotes go wrong. Paper, cardboard and wood carry 8 units per pound. Bound fibre carries 3.6, glass fibre 2.0, and foam or rubber 0.5.

What sits inside the bagUnits per poundWhy it matters
Paper, cardboard, wood8.0The term buyers forget
Bound fibre pads3.6Common in furniture crates
Glass fibre2.0Rarely met outside industry
Foam or rubber0.5Low, but not zero

Work one through. A 12 inch cube has an area of 864 square inches, because six faces of 144 inches each.

Multiply by 0.011 and you get 9.5, so the bag needs 10 units. At 26 grams a unit, that is 260 grams.

Now put two pounds of corrugated inside the same bag. The allowance adds 16 units, and the requirement jumps to 26 units, or 676 grams.

Two pounds of cardboard took the bag from 10 units to 26. That single line explains most of the moisture failures I see on arrival.

The MIL-STD surface-area formula is published with a calculator, and the dunnage table sits beside it.

Comparison bar showing a twelve inch bag needing ten desiccant units empty and twenty-six units with two pounds of corrugated board inside
The same bag, before and after two pounds of cardboard.

There is a second route for barrier bags, and it starts from the film instead of the volume.

Water crossing the film equals the permeation rate times the area times 30.4 times the months of shelf life. Divide that by capacity at the target humidity.

The permeation route used for barrier bags is the better one when the film is the weak point and the pack barely leaks.

Whichever route you use, the bag has to be sealed. In an open carton the desiccant pulls moisture from the room until it is full, and then it stops helping.

Why Containers Rain

A container full of cartons can arrive with water dripping from the ceiling. It did not leak. The water was inside from the start.

Warm air holds more water than cold air. That single sentence is the mechanism, and the rest is timing.

By day, sun on the steel pushes wall heat to 60 or 70 °C. The air inside warms and its capacity to hold water climbs.

At night the steel radiates heat away and can fall 20 to 30 °C in a few hours. The air inside cools more slowly.

When the wall drops below the dew point of that air, water condenses on the metal. Enough of it gathers at the ceiling and drips onto the cargo.

The moisture comes from three places. The cargo. The pallets and packaging. The air sealed in at loading.

A load closed in a tropical port at 30 °C and 85 percent humidity is the textbook case. Open it in a European winter at 5 °C and the water arrives with it.

Any route with a drop above 15 °C is worth treating as high risk. Trans-equatorial moves are worse, because the container passes through the humid belt first.

Sizing a container is coarser than sizing a bag. A 20 foot box holds about 33 cubic metres. The air inside it at 25 °C and 80 percent humidity carries roughly 550 grams of water.

That is the air alone, before the cargo adds anything. A supplier that sizes container loads puts a 20 foot box at 6 to 8 units for a moderate route. A hot or long route takes 10 to 12.

A 40 foot box roughly doubles it. Hygroscopic cargo such as wood, paper or coffee adds 50 to 100 percent, and each extra week beyond two adds 10 to 15 percent.

Placement matters as much as count. Units hang from the lashing rings near the ceiling, spread along both sides, never lying on the cargo and never over a vent.

Diagram of container condensation: hot steel wall by day, cold wall at night below the dew point, water forming at the ceiling and dripping on cartons
Day heat, night drop, dew point, drip. The cargo never got wet outside.

Why containers rain is explained in more detail on a supplier’s own guide, which is where the wall temperatures above come from.

Blue, Orange, And Why Blue Is Leaving

Plain gel gives no signal. Indicating gel is doped so the colour reports how much water it has taken.

The classic version is blue when dry and pink when spent. The colour comes from cobalt chloride, added at the factory.

Cobalt chloride is classified as a carcinogen. The European Union reclassified it in July 2000, and it is now forbidden there for use in silica gel.

A buyer shipping into Europe therefore has a decision to make before the artwork, not after. Blue beads are the most recognisable and the least welcome.

The common replacement is methyl violet, which runs orange when dry and green when wet. Its toxicity is low, and it is still not a food additive.

Iron salts are the cleaner option again. Ferric sulfate and related salts shift from amber to almost colourless as they take water, with no cobalt and no dye.

One rule covers every version: indicating gel is for equipment, not for food or medicine. The poison centre says the same, and so does every packaging guide I have read.

“Do Not Eat” Is About Choking

The warning on the sachet is loud. The chemistry behind it is milder than the wording suggests.

Silica gel is described by poison centres as usually non-toxic. Swallowing a packet should cause no symptoms unless the person chokes on it.

Blockage of the digestive tract has happened, in children and in adults, but it is rare. That is the real hazard: a small object, not a poison.

Skin contact may cause redness. Dust in the eye irritates. Breathing dust can irritate the airway and cause coughing.

The blue bead is the only chemically interesting one. Cobalt chloride is present at about 1 percent or less, which the poison centre treats as usually safe in small amounts.

A larger amount is a different question, and the answer is to call a poison centre rather than to guess.

One confusion is worth clearing for spec sheets. Crystalline silica dust can cause silicosis. Synthetic amorphous silica gel is not crystalline, and the reference page states plainly that it does not cause silicosis.

The poison centre’s own answer is three short paragraphs, and it is the best thing to quote in a care note.

For a pack, the practical wording is short. Do not eat. Keep away from children and pets. If swallowed, rinse the mouth and call a poison centre if there is any concern.

Food Grade Is A Paper Trail

“Food grade” on a sachet is not a claim about the beads alone. It covers everything the food could touch.

Silicon dioxide is listed by the US FDA as generally recognised as safe. It may be added to food at up to 2 percent under 21 CFR 172.480.

A 2018 re-evaluation by the EFSA panel on food additives found no indication of toxicity, even at the highest estimated exposure.

That covers the substance. For a packet, the film, the ink and the seal are also food-contact materials, and each one has to be authorised.

The paper to ask for is a letter of guaranty, plus the declarations behind it. A certificate with no material list answers the easy half of the question.

How a food-contact material is classed explains the rest of the paperwork.

Never specify indicating gel for a food or medicine pack, whatever the supplier offers. The colour is there for equipment, and the restriction on cobalt makes it a poor idea even where it is legal.

If the pack reaches California, the label side of this is a separate decision. What a California label must say belongs in the artwork brief.

Seven Lines For The Order Sheet

Seven lines keep a commodity item from becoming an argument. Each one is a number or a document.

One. The agent. Silica gel, clay, molecular sieve or calcium chloride, with the bead or granule form named.

Two. The unit basis. The standard used, and the grams per unit agreed in writing. 26 and 33 are both in the market.

Three. The wrap. Paper, non-woven or film, with the seal type, because the wrap sets the drying temperature.

Four. The capacity. A figure at a stated relative humidity, with the method used to measure it.

Five. The indicator. None, orange or blue, and the market it ships to. This decides whether the order is legal at the destination.

Six. The food-contact file. Grade, component declarations and the letter of guaranty, when the pack goes near food or medicine.

Seven. The count and the warning. Units per carton, carton dimensions, and the exact warning text to print.

All seven fit on one page. The sheet that carries the unit count is what the line actually works from.

Then check the packed carton, not the sample. A check on the packed carton catches the two failures here: too few units, and a wrap that splits at the seal.

Freight is the last line of the sum. What inbound freight adds matters once the sachets start weighing something.

UNIT CHECK

Send me the sachet spec, the carton plan or a photo of the label. I will check which agent it really is, what a unit weighs, and how many units the pack needs once the cardboard is counted. I will also say whether the indicator is allowed at your destination. No cost, no obligation.

Check My Spec

Questions Buyers Ask

Is silica gel poisonous if someone eats it?

Usually not. Poison centres treat a swallowed packet as non-toxic, and the real risk is choking or, rarely, a blockage. Large amounts of blue gel are the exception worth a call.

Why does a full sachet feel dry?

Because the water sits on the pore walls rather than in the open. The beads stay hard and free-flowing, so a spent sachet looks and feels like a new one.

Should I order blue or orange indicating gel?

Orange, for most markets. Blue uses cobalt chloride, which is forbidden in Europe for silica gel, and neither version is for food or medicine packs.

Can the sachets be dried and reused?

The gel can. The wrap usually cannot. Loose gel takes 105 to 130 °C for four to six hours in an electric oven. Some sachets are rated to 80 °C, and others are sold as single use.

How many units does a 20 foot container need?

A supplier that sizes container loads puts a moderate route at 6 to 8 units and a hot or long one at 10 to 12. A 40 foot box roughly doubles it.

Is a desiccant the same as an oxygen absorber?

No. A desiccant removes water vapour. An oxygen absorber uses iron powder to remove oxygen. They solve different problems and should not be stored together.

Questions & Comments

We read every one and reply within 24 hours

If a desiccant spec is on your desk, send it. I will check which agent it names, what a unit weighs, and how many units your carton actually needs.

0
Would love your thoughts, please comment.x
()
x