Food Grade Plastic: A Claim About One Part, Not A Resin
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Food Grade Plastic: A Claim About One Article, Not A Resin

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 11, 2026 · 13 min read

Food grade plastic is a part tested for its intended use.

The word describes a status. The status belongs to a part number, a test report and a temperature range.

It does not belong to the name of a resin. Polypropylene can be food grade in one factory and not in the next, because the two plants buy different additive packages.

Most catalogue pages skip that difference. They print a triangle with a number inside, then a column that says yes or no.

That table is the reason buyers get caught. It looks like a safety rating, and it is not one.

This article pulls the claim apart. It gives the federal rule behind each resin. It also shows the two grades hidden inside one resin and the test that decides the answer. Then it lists the four papers to ask for before a deposit.

Studio still life of plain white plastic food containers and a clear bottle arranged on a beige surface
Same family of resins, four different answers on food contact.

The Short Answer

A plastic article is food grade when four things hold at the same time. Take any one away and the claim fails.

One. The resin is listed for food contact. In the United States that listing is a section of the Code of Federal Regulations. In Europe it is a line in the union list of Regulation (EU) No 10/2011.

Two. Every additive is listed too. Antistatic agents, slip agents, light stabilisers and colours each need their own permission. A resin that passes can still fail on what was mixed into it.

Three. The finished part passed a migration test under the conditions it will meet in use. Hot, fatty and acidic food each pull more out of the wall than water at room temperature.

Four. The paper trail names the rule. A supplier who cannot name the section or the regulation is repeating a word from a brochure.

Now the term beside it. Food safe is the narrower idea, and the two are not the same claim.

Food grade is about how the item was made. Food safe is about how it is used.

A cup made under the right rules is still not food safe when it holds hot soup. The wall was tested for cold liquid, and the buyer moved it outside its own range.

One more thing about the American side. No federal rule uses the words food grade at all.

The FDA authorises substances, not finished products. A food contact substance must be permitted for that use before it is sold, usually through a food contact notification.

So the honest version of the question is not which plastic is food grade. It is whether each substance in this part is authorised for this food, at this temperature, in this thickness.

Why The Number On The Base Is Not A Rating

The triangle with a number from one to seven is a sorting code. It tells a recycling line what the part is made of.

It says nothing about heat, nothing about migration, and nothing about whether the part may touch food.

Search guides repeat the same table anyway. Resins 1, 2, 4 and 5 are marked safe; 3 and 6 are marked unsafe; 7 is marked safe again.

That table cannot hold. Polystyrene is the clearest test, because it sits in the same list as the two rejects.

Polystyrene has its own food contact section, 21 CFR 177.1640. The text allows it as a component of articles that touch food.

The section sets a cap on leftover styrene: no more than 1 percent by weight. When the article meets fatty foods, the cap tightens to 0.5 percent.

Those are numbers a lab can test. They are not a yes or no sticker, and they do not match the table.

Polyvinyl chloride is the second counter-example. One UK moulder lists it for cling film and sandwich bags. The resin is not the problem; the plasticiser package is, and that package has its own rules.

Where the code still helps is triage. It tells you roughly how the wall behaves.

PET is stiff and clear. HDPE is opaque and stiff. LDPE is soft. PP takes heat. PS is cheap and brittle.

Use it to narrow the shelf. Never use it to close the question.

The Five Resins That Carry Most Orders

Five resins cover most kitchen and storage goods that leave a Chinese factory. Each one has a job it does well and a job it does badly.

The table below is a starting point for a brief, not a ruling on any single part.

ResinCodeUsual partWhy buyers pick itWhere it struggles
Polypropylene5Lunch boxes, jugs, lids, rice cookersStiff, cheap, holds hot foodClouds after many hot washes
HDPE2Cutting boards, jugs, storage tubsTough, opaque, easy to cleanSoftens sooner than PP in heat
LDPE4Bags, wraps, squeeze bottlesSoft, cheap, seals wellWeak wall, poor shape holding
PET1Water bottles, cold cups, traysClear, strong, good barrierDistorts with hot fill
Polystyrene6Cutlery, yoghurt pots, takeaway basesVery cheap, moulds fastBrittle, low heat resistance

Two notes on that table. Both change what you order.

PET is the clear one, and clear is why it dominates cold drinks. A hot fill will distort the same bottle, so the grade and the fill temperature have to be chosen together.

Polypropylene is the workhorse, and a buyer should know its published specification. The olefin polymer section, 21 CFR 177.1520, gives density from 0.880 to 0.913 grams per cubic centimetre.

The same table gives a melting point of 160 to 180 °C for polypropylene. That figure is a property of the resin, not a safe working temperature for a box.

Mixing those two numbers is a common mistake in a spec sheet. A melting point near 165 °C does not make a lid safe at 165 °C.

What it does tell you is why PP wins on hot food and PS loses. Polypropylene in kitchenware also shrinks in the mould, so wall thickness and rib design move together.

Chart of five plastics by resin code with typical kitchen parts and the one property each is chosen for
Five resins, five jobs. The code only tells you which one you are holding.

One Resin, Two Grades

Here is the part almost no supplier page explains. A single resin can be listed twice in the same federal section, with two different limits.

Polyethylene is the clearest case. Item 2.1 covers polyethylene for articles that contact food. Item 2.2 covers polyethylene for articles used to pack or hold food during cooking.

The two items carry the same density range. They do not carry the same extraction cap.

Item 2.1 allows up to 5.5 percent extractables in n-hexane at 50 °C. Item 2.2 allows 2.6 percent under the same test.

So “food grade HDPE” is half a sentence. The half that matters is which item the resin was bought against, because a cooking use needs the tighter number.

ResinWhat is cappedLimitTest condition
Polyethylene, not for cookingn-hexane extractables5.5 %50 °C
Polyethylene, cooking contactn-hexane extractables2.6 %50 °C
Polypropylenen-hexane extractables6.4 %Reflux
PolypropyleneXylene solubles9.8 %25 °C
PolystyreneResidual styrene monomer1.0 %0.5 % for fatty food

Read the last row twice. The same polystyrene is allowed 1.0 percent residual monomer in general, and 0.5 percent when it meets fatty food.

Fat is the reason. A fatty food pulls more from the wall, so the rule asks for a cleaner starting point.

Colour is the other half of the grade question. A pigment needs its own permission under 21 CFR 178.3297 before it can go into a food contact part.

This is where a cheap quote hides. The resin may be right, the mould may be right, and the masterbatch may come from a supplier who never asked the question.

Ask for the colour name and its code, not just “any colour is fine”. A buyer who accepts a verbal answer owns the result.

Bar chart comparing the extraction limits for polyethylene used with cooking and polyethylene used without cooking contact
One resin, two items in the same rule. Cooking contact takes the lower cap.

Choosing A Substitute Without Losing The Claim

Most projects change resin once. A price moves, a colour fails, or a buyer asks for a clearer body. The swap is where a food grade claim quietly breaks.

Four checks keep it whole. Run them in this order, and the price comes last.

Check one. Is the new resin listed for the same use? A resin can be allowed for cold contact and not for cooking contact. That is the polyethylene split above, and it repeats across other sections.

Check two. Does the additive package come with it? A new resin usually means a new masterbatch, and the colour has to be allowed at its own level.

Check three. Does it hold at the use case? A switch that gains heat resistance can lose fat resistance. The test has to be run again, not carried over.

Check four. Does the mould survive the change? Shrink and stiffness differ between resins, so a tool cut for one may not fill for the other.

Now the common swaps, with the trap in each.

Polystyrene to polypropylene. This is the usual move when a part fails on heat. Both are cheap, but PP warps differently and needs a different wall.

Polycarbonate to a copolyester or to PP. Polycarbonate carries the code 7 label, which tells a buyer nothing useful. The question to settle is legal, not chemical.

PVC film to polyethylene film. The plasticiser package was the risk, not the resin. A change of resin without a change of additives has fixed nothing.

One family sits outside this list. Melamine is a thermoset, so melamine dinnerware answers to a different set of tests. Swapping a thermoplastic for it is a new project, not a substitution.

Write the swap into the brief as a new part. Two lines change, the test changes, and the old report stops covering the order.

What A Migration Test Measures

Migration is the mass that leaves the plastic and enters the food. A lab measures it in two ways, and buyers mix up the two.

Overall migration weighs everything that moved. It does not care what the substance was.

Specific migration follows one named substance against its own limit. A part can pass the total and still fail on one ingredient.

The European rule sets the overall migration limit at 10 milligrams per square decimetre of surface.

The same regulation does the arithmetic for a buyer. A cube holding one kilogram of food, with one square decimetre of contact per kilogram, works out at 60 milligrams per kilogram of food.

That arithmetic is why small parts are the harder case. A lid has more surface for its weight than a tub, so the same wall gives up more per kilogram of food.

This is the number to hold on to when a supplier says the material is fine. Material is the input. Migration is the result.

How the lab gets there is also worth knowing. It picks a liquid that stands in for the food, then holds the sample at a time and temperature that copy the real use.

Change the liquid, the time or the temperature and you have a different test. That is why a report has to name all three.

One more line from the regulation helps a small buyer. A test is slow and costly, so showing the limit is met by calculation or modelling is allowed.

Ask for the calculation then, not for the absence of a test. A written estimate you can read beats a certificate you cannot open.

Heat And Fat Move The Limit

Three things move the answer: how hot, how long, and how fatty the food is. Each one changes what the wall gives up.

Heat is the first. A box tested for a short contact at room temperature is not the same article as one tested for a long contact at oven heat.

Fat is the second, and it is written into the rules. Polystyrene may hold 1.0 percent leftover styrene in general and only 0.5 percent when it meets fatty food.

Polyethylene shows the same logic in another form. The item for cooking contact allows 2.6 percent extractables, against 5.5 percent for the item that never sees cooking.

Time is the third. A part that holds sauce for a minute is not tested like a part that holds oil for a month.

So a brief that says “for food” has told the factory almost nothing. A brief that says “hot soup, 95 °C, four hours in a delivery bag” has told it which test to run.

Write the use case before you write the material. The use case picks the grade, and the grade picks the price.

What Changed With BPA

Bisphenol A is a starting substance for polycarbonate and for the epoxy linings inside cans and lids. It has been the loudest food contact story of the decade.

The European Union moved from a limit to a ban. the BPA regulation of December 2024 covers BPA in plastic food contact articles and in varnishes and coatings.

It amends Regulation (EU) No 10/2011 and replaces the earlier BPA rule from 2018. The old rule had worked through a specific migration limit of 0.05 milligrams per kilogram of food.

The reason for the change sits in the safety review. The EU food safety body set a tolerable daily intake of 0.2 nanograms per kilogram of body weight.

That figure is 20,000 times lower than the temporary value it had used in 2015, which was 4 micrograms per kilogram. A limit built on the old figure no longer held.

The phase-out is not instant. The regulation gives 18 months for most articles, and 36 months for varnishes and coatings on the outer surface of metal packaging.

For a buyer the lesson is a paperwork one. “BPA free” is a claim about a material. “Can be sold in the EU” is a claim about a date.

Ask for both in writing. A supplier answering the first question has not answered the second.

The Four Papers To Ask For

Food grade is a claim, and a claim needs a document behind it. Four papers do most of the work.

One. The resin data sheet. It should name the grade, the supplier and the density or melt index. Without a grade name, the sheet describes a family rather than a material.

Two. A statement of which rule the part meets. On the American side that means a section number such as 21 CFR 177.1520 or a food contact notification. On the European side it means a declaration of compliance.

Three. The migration report. It has to name the liquid, the time, the temperature and the surface area. A report without those four is a page of reassurance.

Four. A colour and additive list. Each pigment needs its own permission, and the masterbatch supplier is often a third company.

Two of those four often arrive as one file. Ask which is which before you accept it, because a declaration of compliance is a statement, not a test.

The European declaration also carries a duty. The rules require it to travel with the material through each stage of the chain, and the supporting evidence has to be kept.

So a factory that says “we can send it later” has told you it does not hold the file. That is worth knowing before a deposit rather than after a shipment.

What a kitchenware surface has to meet is set out in more detail in the guide to food contact materials for kitchenware. The document set is the same shape.

Checklist of four documents to request before a food grade plastic order, with the question each one answers
Four papers, four different questions. One page rarely answers all of them.

Six Lines For The Order Sheet

These six lines turn a word into something a factory can build and a lab can test.

One. Resin name, grade and the rule section. Write 21 CFR 177.1520 item 2.2, not “food grade PE”.

Two. Colour by name and code, with the additive statement attached.

Three. The use case in numbers: food type, highest temperature and contact time.

Four. Wall thickness at the food contact face. Thin walls change both migration and feel.

Five. The document set, listed, due before the first shipment.

Six. The test to be repeated on the production sample, and who pays for it.

Line one and line three carry the most weight. Everything else follows from them, including the price.

Put those six lines on a single written spec page and the quotation becomes comparable with the next one.

Then let a third party check the run against the same page. The inspection that happens before the carton closes is the cheapest place to catch a wrong resin.

A silicone part follows a different rule book but the same habit. What food grade silicone has to show is the same four documents with different numbers.

GRADE AND LIMIT

Send me a quotation, a resin data sheet or the migration report you were given. I will check which rule the part claims to meet, whether the grade matches the use case, and whether the colour has its own permission. If a document is missing, I will name the one that matters most for your market. No cost, no obligation.

Check My Papers

Questions Buyers Ask

Is polypropylene or HDPE better for food?

Both can be food grade. PP holds hot food and repeated washing better. HDPE is tougher and cheaper for cold storage. The use case picks between them, and the rule section decides whether either grade is allowed.

What does food grade mean on a plastic box?

That the resin, every additive and the finished part are allowed to touch that food. It also means a migration test was run at the stated time and temperature. A box with no stated use has no test behind it.

Does the recycling number prove a plastic is food grade?

No. The number from one to seven is a sorting code for recycling lines. It says what the part is made of. It says nothing about heat, additives or migration, and it is not a safety rating.

Is recycled plastic allowed in food contact parts?

Only when the source and the process are accepted by the market you sell into. Recycled flake with a resin code stamped on it proves nothing. Ask for the authorisation paper, not for the word recycled.

Can I put hot food in a food grade container?

Only inside the range it was tested for. The same part can be fine for cold salad and wrong for hot soup. Ask for the test time and temperature, then compare those to your own use.

Which documents should a new supplier send?

A resin data sheet with the grade name, a statement of the rule the part meets, a migration report with four test conditions, and a colour statement. A supplier who holds all four answers in days, not weeks.

Questions & Comments

We read every one and reply within 24 hours

If a resin data sheet or a migration report lands on your desk, send it over. I will name the rule it claims to meet and the line that is usually missing.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x