What Is EVA Foam? Density, Hardness, And The Spec Sheet
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is EVA Foam: Density, Hardness, And The Sheet You Buy

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao
· Updated November 11, 2026 · 12 min read

EVA foam is ethylene-vinyl acetate copolymer, foamed and cross-linked into a closed-cell sheet.

The name tells you the chemistry. It does not tell you what you are buying.

Two sheets can both be called EVA foam and behave like different materials. One is soft enough to fold into a yoga mat. The other is firm enough to mill into an insole board.

The gap is density and hardness, and both are numbers your supplier can print on a datasheet today.

A cream EVA foam mat and a rolled exercise mat on a beige studio surface
The same polymer family covers a 35 kg/m³ yoga sheet and a 170 kg/m³ board. The datasheet is what separates them.

This article covers three things. What the word EVA actually names, how density and hardness are measured, and the six lines that turn a quote into a spec.

The Short Answer

EVA is a copolymer of ethylene and vinyl acetate. The vinyl acetate part softens the plastic and makes it rubbery, so the resin bends instead of cracking.

To turn it into foam, a factory melts the resin with a blowing agent and a cross-linking agent, then heats it under pressure. Gas expands inside the melt, and the links between chains hold the bubbles in place.

The result is a closed-cell foam. Each bubble is sealed, so water does not wick through the sheet. That is why an EVA mat survives a wet gym floor and a spilled drink.

Everything after that is a grade question. Foam density is quoted in kilograms per cubic metre. A supplier’s own datasheet can sit anywhere from about 33 to 280 kg/m³ for standard sheet goods.

Hardness is a separate number, read on a gauge with its own scale. Density and hardness move together in practice, but they are not the same measurement and cannot be swapped.

So a buyer needs two figures, not one. Density tells you the mass and the cost. Hardness tells you how it feels underfoot and how it behaves when compressed.

What The Word Actually Names

Three different things get sold under the same two syllables, and the confusion starts here.

The resin. EVA copolymer in pellet form, sold by chemical makers. This is what a foam factory buys by the tonne.

The foam. Cross-linked, closed-cell sheet or block. This is what a mat factory buys, usually in sheets of a fixed size and thickness.

The finished part. A cut mat, a printed tile, a moulded insole. This is what a brand buys.

Most quality problems start when one party talks about the resin and the other hears the finished part. A resin datasheet says nothing about cell size, hardness or how the sheet was cut.

EVA is also not the only foam in the room. PE foam, PU foam and EPE look similar on a sample table and behave differently in use. If the quote says only “foam”, ask for the polymer name in writing.

Making the sheet takes one of two routes. Continuous foaming produces a long block that is later split into sheets. Compression moulding produces a shaped part in a heated press, which is how interlocking puzzle tiles and embossed mats are made.

The route changes the skin. A split sheet has an open, slightly rough face where the blade passed. A moulded part has a denser skin from contact with the tool, and that skin grips and prints better.

Density: The Number You Can Check

Density is mass per volume, and it is the one figure a buyer can test in the warehouse without a lab.

Take a sheet, measure its length, width and thickness in metres, and weigh it. Divide the mass in kilograms by the volume in cubic metres.

A worked example. A sheet one metre square and ten millimetres thick is 0.01 m³. At 35 kg/m³ it should weigh 0.35 kg, or 350 grams.

If the same sheet weighs 1.7 kg, the density is about 170 kg/m³. You have been quoted a light foam and shipped a heavy one, or the other way round.

Three steps to measure EVA foam density: measure the volume, weigh the sheet, divide mass by volume
Three steps, no lab. Volume, mass, division – and the answer is in kilograms per cubic metre.

That test costs a scale and two minutes. It is also the fastest way to catch a substitution. A heavier sheet costs more, and the swap usually runs the other direction.

Published figures give the working range. A Zotefoams Evazote VA35 datasheet lists 2.18 pcf, which is 35 kg/m³, with a cell size of 0.45 mm. A US converter lists its E400 sheet at 170 kg/m³ nominal.

That is a fivefold difference in mass between two products both sold as EVA foam.

One trap deserves its own line. Product codes are not densities. The E400 sheet above is 170 kg/m³, not 400. Read the data line, never the code.

Density is also the cost driver. Resin is bought by weight, so a denser sheet carries more material per square metre. Two quotes that look far apart are often just two different densities.

What the datasheet saysFigure on a real sheetWhat it tells you
Density35 kg/m³ (VA35), 170 kg/m³ (E400)Mass, cost per square metre, how much material is in the sheet
Hardness, OO scale48 Shore OO (VA35)Soft-foam feel, measured on the OO scale
Hardness, C scale40–45 Shore C (E400)Firmer sheet, measured on the C scale
Compression deflection51 kPa at 25 %, 114 kPa at 50 %How much load the sheet carries before it flattens

Hardness: Three Scales That Are Not The Same

Hardness on foam is where spec sheets get sloppy, because the scale is often left off.

A hardness gauge presses a small point into the surface and reads how far it sinks. The shape of that point changes with the scale, so the numbers are not interchangeable.

Soft EVA is usually measured on the OO scale. Firmer sheet is measured on the C scale. Many Asian factories quote Asker C, which is a different instrument again.

The published figures show both scales in one material family. The 35 kg/m³ sheet carries 48 Shore OO. The 170 kg/m³ sheet carries 40 to 45 Shore C.

Those two numbers look close and are not. A C-scale reading of 45 is a much firmer material than an OO reading of 48, even though 45 is the smaller number.

So a line like “hardness 40” is unusable. It needs three parts to mean anything: the scale, a tolerance, and the test method.

Write it as a range, not a point. A converter selling sheet goods quotes ranges for a reason, and a press does not hold one number across a whole run.

Hardness also drifts with temperature and with thickness. A thin sheet reads harder than a thick one on the same gauge, because there is less material under the point to give way.

That is why a lab note matters. If the report does not say the specimen thickness and the scale, the number cannot be compared with anything.

What A Datasheet Should Tell You

A real EVA datasheet is short and numeric. Here is what the numbers mean, using the figures a maker publishes for a 35 kg/m³ sheet.

Compression deflection. The sheet takes 51 kPa of pressure at 25 percent squeeze and 114 kPa at 50 percent. In plain terms, this is how firm the sheet feels when you stand on it.

Compression set. After 22 hours under 25 percent squeeze at 23 °C, the sheet lost 11 percent of its thickness. It recovered to 3.5 percent loss after a day.

That number predicts the common field failure. A mat left under a heavy rack recovers slowly or not at all, and the dent stays in the product.

Tensile and elongation. 615 kPa of tensile strength and 180 percent elongation at break. Lower elongation means a sheet that tears instead of stretching when a die cuts it.

Tear strength. 730 N/m. This is the figure that decides whether a puzzle mat edge survives being pulled apart twice a week.

Cell size. 0.45 mm on that grade. Finer cells give a smoother cut face and better printing. Coarser cells give more cushioning per gram.

Thermal conductivity. 0.0394 W/m·K. This is why an EVA mat feels warm rather than cold, and why it works as light insulation.

Burning behaviour. The same sheet passes FMVSS 302, the vehicle interior burn test, at 1.6 mm per second on a 5 mm sample.

None of these numbers is exotic. Any serious foam factory has them, usually from a test house, and should send them on one page.

If a supplier answers a hardness question with a photograph of the sample, the conversation has not started yet.

Heat Is The Limit Most Buyers Miss

EVA foam is sold as tough and weather resistant, and for most indoor uses it is. The temperature ceiling is where surprises happen.

The same datasheet gives a service range of minus 70 °C to plus 75 °C. That is the band the maker states for the material, not a marketing number.

Seventy-five degrees is not far above a hot summer surface. A dark mat in a parked car, or a sheet stored against a metal roof, will pass it.

The stated service band of an EVA foam sheet from minus 70 to plus 75 degrees Celsius, with the zone past the ceiling shaded
The stated band ends at 75 °C. Past it the foam softens and takes a set, which is where curled mat edges come from.

What happens then is not a fire. The sheet softens, takes a set, and comes back the wrong shape. Curled edges on a mat are usually a heat story, not a cutting story.

The cold end is friendlier. At minus 70 °C the material is still usable, which is why EVA appears in cold-climate padding and in freezer-room flooring.

So the question for the order sheet is not “is it heat resistant”. It is where the product will sit, and whether the stated ceiling clears that place with margin.

Yoga Mats And Floor Mats Are Different Animals

The same factory can make both, and the spec should not be copied across.

A yoga mat is thin and grippy. It is used barefoot, rolled up daily, and judged on surface feel rather than on load bearing.

A gym floor tile is thicker and denser. It carries a rack, a bench and a pair of dumbbells, and it is judged on how little it dents.

A play mat sits between the two. It is soft, printed, and usually joined edge to edge, so the joint takes as much abuse as the surface.

Thickness tells you which family you are in before density does. Retail listings for multi-purpose EVA tiles quote 10 mm and 13 mm as standard sizes, while a rolled exercise mat is commonly offered thinner.

Thicker is not automatically better. A 13 mm tile at low density compresses more than a 10 mm tile at higher density. The price difference can buy the wrong thing.

Joinery is the other split. A puzzle edge needs a mould. A printed tile needs a press and an ink system, and a plain roll needs only a splitter and a die.

That is where the tooling conversation belongs. The shape decides the process, and the process decides the minimum order far more than the material does.

ProductThickness in the marketWhat decides quality
Rolled yoga matThin sheet, split from blockGrip, surface skin, compression set, smell
Gym floor tile10 mm and 13 mm in retail listingsDensity, compression deflection, edge stability
Interlocking play matMoulded tile with puzzle edgeJoint strength, print adhesion, child-safety tests
Insole board3 mm to 6 mm, firmer gradesHardness on the C scale, dimensional stability

The Test List For A Play Mat Or A Toy

Anything sold for children gets tested, and the tests are named. A claim of “non-toxic” is not one of them.

The European toy standard EN 71 comes in parts. Part one covers mechanical and physical hazards, part two covers flammability, and part three covers migration of certain elements.

For an EVA mat, part three is the one buyers quote, because a child chews and a coloured surface can carry metals from pigments.

Chemicals are handled separately. REACH Annex XVII restricts a list of substances in consumer articles, including a group of polycyclic aromatic hydrocarbons and several phthalates.

Formamide deserves a mention of its own. It can be left behind by certain blowing agents. Europe treats it as a substance of concern, and play mats are exactly where buyers ask about it.

Ask for a formamide figure on a report for the finished mat, not for the resin. The residue is a process outcome, so it depends on how the sheet was foamed and how long it was cooked.

For the United States, the rules come from the consumer product safety framework. It covers lead content and a set of phthalates in children’s products.

Then there is the case where the mat touches food. EVA is allowed as a food contact material in the US under 21 CFR 177.1350, . That rule caps chloroform-soluble extractives at 0.5 mg per square inch.

The same section allows the film to be irradiated to cross-link it. The maximum absorbed dose is 150 kGy from an electron beam, and 5 to 50 kGy from a cobalt-60 source.

None of this applies to a gym mat. It applies to a lunch mat, a placemat, or a tray liner. That is the kind of line that gets missed when a mat is sold in a kitchen context.

Cutting, Printing, And The Cost Levers

Two quotes for the same drawing can differ by half, and material is only part of the reason.

Density. Resin is bought by weight. Going from a light sheet to a firm one raises the material cost per square metre in a straight line.

Cutting. A steel die is fast and cheap per piece but needs a tool per shape. CNC cutting skips the tool and charges by machine time instead.

Printing. Heat transfer and film lamination both add a layer. That layer has its own adhesion and migration tests, so a printed mat carries two material conversations.

Regrind. Offcuts can go back into some foam recipes. The trade-off is cell uniformity, and a sheet with visible specks or a rough face usually tells you where the regrind went.

Tolerance. Foam is compressible, so thickness is measured under a light load and quoted with a tolerance. A tight tolerance on a soft sheet is a sorting cost, not a material cost.

Ask which lever moved when a price drops. A cheaper sheet is usually thinner, lighter, or cut from a different block, and the datasheet will show which.

Six Lines For The Order Sheet

These six lines fit on one page, and each one points at a document rather than a claim.

One, the polymer and the grade. EVA, plus the maker’s grade name. A grade name can be traced to a datasheet, and a datasheet can be compared.

Two, density with a tolerance. In kilograms per cubic metre, not a word like light or firm. Keep the weigh-and-divide check in your own warehouse.

Three, hardness with its scale. Shore OO, Shore C or Asker C, with a tolerance and the specimen thickness. Without the scale the number is decoration.

Four, compression set. Name the test condition, not just the result, so two factories are answering the same question.

Five, thickness and sheet size. State the tolerance and how thickness is measured. Foam is compressible, so the load on the gauge changes the reading.

Six, the end use and its test list. Child use brings EN 71 and the chemical restrictions. Food contact brings the food contact rule. A gym tile needs neither, and paying for both is waste.

The same discipline applies to how a mat is weighed. Weight per square metre is the same idea as fabric weight per area. It is the fastest way to compare two sheets of different thickness.

Put the six lines into the one-page brief the factory signs off before a sample is approved, then check the first run against it.

If the part is moulded rather than split, the press settings matter as much as the recipe. The same logic runs through how compression moulding is run in China.

Then let someone independent look at the goods. A pre-shipment check on the finished run with weight, hardness and surface on the list catches the swap after the sample was approved.

Six numbered lines for an EVA foam order sheet, with the document each line points at
Six lines, each pointing at a document. A quote that cannot answer all six is not yet a spec.
SEND THE DATASHEET

Send the EVA datasheet and the product drawing. I will check the density figure and the hardness scale. I will also read the test list against the market you sell into. You will hear which line is missing before the sample is approved.

Ask For A Spec Check
Is EVA foam the same as PE foam?

No. They are different polymers. EVA is softer and stretches more, which is why it takes printing and moulding well. PE foam is cheaper and stiffer, and it is the one usually sold as packing foam.

Which number matters more, density or hardness?

Density, if you can only check one. It can be weighed in your warehouse, and it sets the material cost. Hardness is the buying decision, but it needs a scale to mean anything.

Can I compare Shore C with Asker C?

Not directly. The instruments are different, so the readings are different. Compare like with like, and ask for the same scale from every supplier you are quoting.

Why does my mat curl at the edges?

Usually heat. The material has a stated ceiling, and a dark sheet in a hot space passes it. Once the foam takes a set, it stays curled.

Is EVA foam safe for a baby play mat?

It can be, and the proof is a report. Ask for EN 71 part three, plus the chemical restrictions for the market, plus a formamide figure on the finished mat.

Does a heavier sheet always last longer?

No. Density buys mass and cost, not durability by itself. Compression set and tear strength are the numbers that predict how a mat ages under load.

Questions & Comments

We read every one and reply within 24 hours

If an EVA datasheet lands on your desk, send it over. I will read the density figure, the hardness scale and the test list against your market.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x