What Is Acacia Wood, And Which Acacia Are You Buying?
Acacia wood is the timber of trees in the genus Acacia. That is a family of more than a thousand species, not one material. The name alone does not tell you what is in the carton.
Three species carry most of the trade. Mangium is the plantation timber behind boards, bowls and trays. Australian blackwood is the furniture timber. Koa is the Hawaiian one, and it is expensive.
They differ in weight, in hardness, and most of all in how much they move when the air changes. That last figure decides whether your cutting board arrives flat or arrives with a crack.
The Short Answer
Acacia is a hardwood. The commercial plantation species sit between 585 and 640 kilograms per cubic metre when dry, which is heavier than oak and lighter than teak.
It machines cleanly, takes an oil finish well, and holds a sharp edge. That mix is why it turns up in cutting boards, handled tools, trays, and outdoor furniture.
None of that is where the money is lost. Boards fail on two things: a moisture figure written for the wrong climate, and a species name missing from the import file.
This article gives you both. First the material, with the numbers. Then the drying target, the cracking that survives a good kiln, and the four lines that must be on the paperwork before a container leaves.
Acacia Is A Genus, Not A Species
A buyer asking for acacia is naming a group. A factory quoting acacia is naming what it has in the yard. Those two answers can be three species apart.
For the trade, the group narrows to three names. Each has a scientific name, and each behaves a little differently in service.
| Commercial name | Dried weight | Janka hardness | Shrinkage, radial / tangential | T/R ratio |
|---|---|---|---|---|
| Mangium (A. mangium) | 585 kg/m³ | 1,430 lbf | 2.8 % / 7.8 % | 2.8 |
| Australian blackwood (A. melanoxylon) | 640 kg/m³ | 1,160 lbf | 3.9 % / 7.9 % | 2.0 |
| Koa (A. koa) | 610 kg/m³ | 1,170 lbf | 5.5 % / 6.2 % | 1.1 |
Read the last two columns together. Mangium shrinks almost three times as much across the growth rings as it does across the radius.
That ratio is the reason a flat sawn board cups while a quarter sawn board from the same log stays flat. It is also the number a drawing should carry.
Koa is the calm one. Its two shrinkage figures are close, so the wood is stable when the air changes. That stability, and the fact that mature trees are scarce, is why koa costs what it costs.
Blackwood sits between them. It is rated only moderately durable against decay, and it is listed as a sensitiser, which matters for dust control on a sanding line.
One more thing makes the names matter. Australian blackwood is not separable from koa by eye on a finished board. A laboratory can tell them apart. A sample photograph cannot.
The practical result is simple. A quotation that says acacia, and nothing else, has not told you which of these you are getting.
The published figures for mangium also carry a warning. Plantation density moves a lot with tree age and site, so two shipments of the same species can weigh differently.
Heavier blocks usually mean older wood. Older wood is denser, and denser wood moves more in service, because there is more cell wall to lose water from.
How Much A Board Actually Moves
Wood changes size as it gains or loses water. It stops changing once the cell walls are full and the free water is gone. That point is the fibre saturation point, and it sits at 25 to 30 percent moisture content.
Below that point, every point of moisture lost costs width. Above it, nothing moves.
The published shrinkage figures run from the green state to the oven dry state. So the movement per point of moisture is the total shrinkage divided by the fibre saturation point.
For mangium, 7.8 percent tangential divided by roughly 28 points gives about 0.28 percent of width for each point of moisture.
Now put that on a real part. A four hundred millimetre glue up, flat sawn, dried to 12 percent, then sent to a room that settles at 6 percent.
| Cut and direction | Shrinkage used | Movement per point | 400 mm part, 12 % to 6 % |
|---|---|---|---|
| Flat sawn, width across the rings | 7.8 % tangential | about 0.28 % | about 6.7 mm narrower |
| Quarter sawn, width across the radius | 2.8 % radial | about 0.10 % | about 2.4 mm narrower |
| Either cut, along the grain | 0.1 to 0.3 % | under 0.01 % | under 0.1 mm |
The same board, the same species, the same room. The only difference is which way the saw went through the log, and the movement changes by a factor of nearly three.
That is why a breadboard end, a batten or a butterfly key is not decoration. It is there to hold a width that wants to close by seven millimetres.
The estimate has limits and they should be stated. The fibre saturation point is a band, not a fixed number. So the answer is a band too: roughly six to eight millimetres for the flat sawn case.
It is still the most useful number in this article. A tolerance of plus or minus one millimetre on a width is normal. Movement of seven millimetres is not a tolerance problem, it is a design problem.
8 To 12 % Is A Range, Not A Target
Almost every export quotation names a moisture range of 8 to 12 percent. It is a safe answer because it covers most destinations. It is also an answer to a question nobody asked.
Wood in service settles at the moisture content of the air around it. That figure is the equilibrium moisture content, and it changes with the room, not with the mill.
In a heated or air conditioned building the air is dry, and wood settles at 6 to 7 percent. In a warm humid climate it settles higher. Equilibrium moisture content follows the room, not the invoice.
Australia shows how wide the spread can be. The drying quality standard recommends 10 to 12 percent for most of the country. It allows 15 to 18 percent for parts of Queensland, the Northern Territory, Western Australia and Tasmania.
Now place a board between those two worlds. Dried to 12 percent in a warm mill, sold into a heated flat that sits at 7 percent.
Five points of moisture leave the wood after the customer has hung it on the wall. The board does not shrink evenly, so it cups, it opens a joint, or it splits along a glue line.
That is not a factory fault. It is a specification that named a range and forgot the destination.
So write the destination instead. A board for a heated market wants 6 to 8 percent at the time it is packed. A board for a humid market wants 10 to 12 percent, because the wood will pick up water anyway.
Then say how it is measured. Moisture content is the mass of the water divided by the oven dry mass, with the sample dried at 103 degrees Celsius for a day.
A pin meter reads the surface first, and the surface is always drier than the core after a fast kiln. That is why a meter reading taken in the pack can flatter a load.
One more number belongs here. Fungal growth and stain stop below 20 percent moisture content. So a board that reads 22 percent on arrival has travelled wet, whatever the label said.
What Cracks, And When It Cracks
Most cracks in acacia tableware are not caused by a bad board. They are caused by a kiln schedule that ran too fast for the thickness.
The surface dries and sets first. The core is still wet, so it still has to shrink, and it pulls against a shell that can no longer move.
The stress that builds is called case hardening. It is invisible in a flat sawn sample and it shows up when the board is machined, because machining releases it.
That timing is the problem. The buyer sees a flat board at inspection. The customer sees the crack two weeks after delivery.
There are three more places where a crack likes to start.
End grain loses water far faster than face grain, so the ends dry first and split. That is why a good blank arrives with waxed or painted ends.
The pith, the soft centre of the log, is dense with weak tissue. A part cut through the pith will open a check along the centre line almost every time.
And thin sections move faster than thick ones. A four millimetre tray wall reacts to a wet kitchen in hours, while a thirty millimetre block takes days.
The fix is a schedule matched to thickness, plus a rest period after drying so the stress can even out. Ask for both, and ask for the sample to be cut, not just measured.
A cross cut taken from a finished part is the cheapest test there is. If the two halves spring apart when the saw passes through, the load is case hardened.
A solid wood part held under a hot pan meets the same movement problem. The notes on a wooden trivet cover it in a different product.
Three Papers Before The Container Leaves
This is the part that a furniture blog never covers, and the part that stops a container at the port.
One: the US import declaration. The Lacey Act requires a declaration for plant products. It asks for the scientific name of each species, the country of harvest, and the quantity.
Common names are not accepted. A line that says acacia is not a declaration, because acacia is the genus. The species name, such as Acacia mangium, is what the form wants.
The filing route changed. Paper forms stopped being accepted on 1 January 2026, so the declaration now goes through the customs system or through the APHIS web system.
There is a small exemption, and it is narrower than most sellers assume. It applies only when the plant material is no more than five percent of the product weight. It also has to stay under 2.9 kilograms on the entry line.
A solid acacia board is nowhere near that limit. The declaration rules from APHIS are short and worth reading once before the first shipment.
Two: the EU due diligence statement. Wood is one of the seven commodities in the EU deforestation regulation, and the obligation lands on the EU importer, not on you.
The dates are fixed. Medium and large operators start on 30 December 2026. Small and micro enterprises follow on 30 June 2027, and products added to the scope later start on 30 December 2027.
The test has three parts. The land was not deforested after 31 December 2020. The timber was produced under the local law. And the statement carries the geolocation of the plot the log came from.
That last part is the one that reaches back to the mill. A plantation can supply a plot reference. A trader buying from unknown smallholders usually cannot.
Three: the drying record. This one is not a law, and it is the one that saves the most money. Ask for the charge number, the schedule, the final reading, and who took it.
A mill that cannot produce a charge record is drying by feel. That is not automatically bad, but it is unverifiable, and an unverifiable load is a load you cannot claim against.
Add a pre-shipment check to the same file. The notes on what an inspector should look at before the goods leave the factory apply to timber as much as to any other product.
The Tariff Line Is Not “Wood”
Heading 4419 holds tableware and kitchenware of wood, and it is split by article and by species group.
Bread boards and chopping boards sit in 4419.11. Chopsticks sit in 4419.12. Other wooden tableware falls into 4419.19, or into 4419.20 when the wood is classed as tropical, or into 4419.90.
Both the 4419.19 and 4419.90 branches split again between forks and spoons and everything else.
So the line is a decision, not a lookup. It depends on what the part is, and on how the species is classed in the tariff.
This is where the species name earns its keep twice. It satisfies the declaration, and it lets the broker place the goods on the right line without guessing.
An invoice that reads “acacia kitchenware” asks a broker to make two decisions with no evidence. Brokers do that, and then they bill you for the correction later.
What May Sit On The Surface
A wooden board that touches food has two surfaces to think about: the wood itself, and whatever was put on it.
Start with the treatment. The rule on preservatives for wood permits a short list on wooden articles used to hold agricultural products, and the list is specific.
The list names copper-8-quinolinolate, mineral spirits and paraffin wax. Paraffin wax has to make up at least half the solids. It also allows a petroleum hydrocarbon resin and rosins. A zinc salt of sulfonated petroleum is on it too. Pentachlorophenol is allowed only at or below 50 parts per million in the treated wood.
That is the whole list. A treatment that is not on it is not covered, and a load treated with something else has a problem that no sanding will fix.
Now the finish. A coating that is meant to be a food contact surface has to come from the permitted substances for resinous and polymeric coatings.
The rule allows two shapes. A continuous film over a metal substrate. Or, for articles used again and again, a continuous film on any suitable substrate that acts as a barrier between the food and the wood.
A cured oil and wax finish on a board falls into the second group. That is why the tin matters: a hardening oil that is not listed is not a food contact finish, however the label reads.
Two things are commonly claimed and cannot be checked. One is that acacia is naturally antimicrobial. No test method or limit sits behind that sentence, and we do not repeat it here.
The other is that the wood is waterproof. No wood is. Acacia is water resistant, and a board left standing in water will swell and then split at the joints.
If the surface question decides the material, the notes on which food contact papers apply to kitchenware go through the same rules product by product.
A moulded alternative sits on the same shelf. The limits on melamine dinnerware are set in a different way, and the comparison helps when a buyer is choosing between wood and moulded board.
Seven Lines For The Order Sheet
Each line below closes one failure. Together they take about ten minutes to write and save the argument that follows a bad container.
1. Species and origin. Write the scientific name, plus the country and province of harvest. This feeds the declaration and the tariff line at the same time.
2. Moisture content, with a destination. Name the band and the port market, not a range on its own. Ask for the reading at packing, and ask who measured it.
3. Cut. Flat sawn or quarter sawn, and which face the width is measured on. The movement figure follows from this line, not from the species.
4. Machining allowance and stress relief. State the rest period after drying, and require a cross cut sample from the finished part.
5. Finish, by name and by rule. Name the oil or coating, and state that it is permitted for repeated food contact. A brand name alone is not enough.
6. Declaration and tariff. Say who files the US declaration, and which heading the goods will be entered under. Put the answer in writing before production.
7. Packing for moisture. A sealed liner, a desiccant where the route is long, and carton marks that match the packing list. Wet air in a container does the damage that the kiln worked to prevent.
Four of the seven lines are paperwork and three are wood. That split is normal for this product, and it is why the specification sheet matters more than the sample photograph.
The last step is to put the same seven lines on the sheet the factory signs. The pattern is in the specification sheet that a Chinese factory can actually work to, and it transfers to timber without changes.
Send me an acacia quotation, a kiln record or a sample report. I will check the species name against the declaration, the moisture band against the destination, and the finish against the food contact lists. Then I will say whether the cut and the allowance can hold the width your drawing asks for. No cost, no obligation.
Send The RecordQuestions Buyers Ask
Is acacia wood a hardwood?
Yes. It is a flowering tree, so the timber is a hardwood in the botanical sense. The plantation species used for tableware sit between 585 and 640 kilograms per cubic metre when dry.
Is acacia wood waterproof?
No wood is. Acacia is water resistant and dense, so it handles a wet kitchen better than pine. A board left standing in water will still swell, and a glued joint will still open.
What moisture content should I order?
Match the band to the market. Six to eight percent for a heated interior, ten to twelve percent for most of Australia, higher again for the humid north. Name the market on the order, not just the number.
Is acacia wood safe for food contact?
The wood itself is fine. The risk sits in the treatment and the finish. A preservative has to come from the permitted list, and a finish for repeated food contact has to come from the coating lists.
Why did my acacia board crack after delivery?
Usually case hardening. The surface set before the core finished shrinking, and the stress opened when the board was machined or when the air dried out in a heated room. A cross cut sample shows it before shipment.
Does acacia have to be certified?
Not by US law. The declaration needs the species and the country of harvest, not a certificate. For the EU, the due diligence statement needs the plot geolocation, and a certified plantation is the easiest way to supply it.
Questions & Comments
We read every one and reply within 24 hoursIf an acacia quotation or a kiln record crosses your desk, send it over. I will check the species name, the moisture band against the market, and the finish against the food contact lists.