Ramekin: Two Products, One Word, And A Depth Rule
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is A Ramekin: One Word For Two Different Dishes

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 11, 2026 · 11 min read

A ramekin is a small, straight-sided dish for one portion.

That is the version sold to a home baker. In a commercial kitchen the same word usually means a small plastic cup for sauce.

The two share a name and almost nothing else. Different body, different test, different case pack, different buyer.

This article separates them. Then it gives the sizes, the number that decides the food-contact limit, and the lines that belong on an order sheet.

Studio still life of two white ceramic ramekins on a beige surface, one filled with a baked custard
Straight sides, one portion, and a rim built to take a flame.

The Short Answer

The usual capacity range runs from 50 to 250 millilitres. That is about 1½ to 8½ US fluid ounces.

The shape is a bowl whose sides rise straight from the base. A traditional one carries fluting on the outside.

Straight sides are not a style choice. They give a custard or a batter a wall to climb, so the middle rises instead of spreading.

Fluting is decoration. It also hides a small dent in a moulded wall better than a smooth surface does.

The name is older than the shape. A French ramequin was a cheese or meat dish baked in a small mould. The word itself traces back to a Dutch term for toasted or minced meat.

So the dish was named after a recipe rather than a measurement. That is one reason the word is so loose in a catalogue today.

Heat is part of the job description. The classic use is a custard set in a water bath, then finished with sugar burnt under a torch.

A dish sold for that has to take a flame at the rim right after it leaves the oven. That is a harder demand than baking alone.

One Word, Two Products

Open a supplier catalogue and the word splits in two.

The baking dish. Ceramic, stoneware or glass, sold in sets of four to a home baker. It goes into the oven and then onto the table.

The portion cup. Melamine or thin plastic, sold by the dozen or the thousand. It holds sauce, dip, olives or a lemon wedge.

A listing that says 4 oz ramekin can be either one. Both appear under the same heading on distributor sites, at similar prices and in the same search.

The gap shows at the oven door. Melamine dishes are sold as no oven and no microwave, and the better listings print both to stop returns.

Porcelain of the same size is sold with a temperature attached. One 4 oz model carries an oven rating of 450 °F.

Case pack follows the market. A porcelain 4 oz comes 48 to a carton from one brand and 36 from another. The plastic cup is usually priced by the dozen.

Ask which product the brief means before you ask for a price. The answer changes the mould, the test report and the carton.

The Size Ladder

Ounces are the trade language. Millilitres are the same figure in another measure, at 29.5735 to the US fluid ounce.

Almost every listing sits on the ladder below. The right-hand column is the job that size usually gets.

SizeVolumeWhat it holdsWhere it turns up
2 oz59 mLJam, honey, one dipBreakfast tray
4 oz118 mLCrème brûlée, panna cottaRestaurant default
6 oz177 mLBaked egg, soufflé, dipMost retail sets
8 oz237 mLMac and cheese, gratinSold as soufflé dish
10 to 12 oz296 to 355 mLSoup, mini pieClose to a baking dish

The volume column is arithmetic, not a supplier figure. Each value is the ounce figure multiplied by 29.5735.

Retail sets cluster at 6 oz because one size then covers baked eggs, a soufflé and a dessert. A set of four in that size is the shape most shops stock.

Foodservice goes smaller and buys differently. The 4 oz cup is the working size for cold garnish and sauce, ordered in dozens rather than sets.

One warning on all of these figures. Capacity is quoted to the rim. A cook leaves space below it, so the food that actually fits is less.

That gap is not a fault. It is why a 4 oz mould can hold a 3 oz dessert and still look full.

Capacity Is Not Footprint

Four dishes, all sold as 4 oz, four different widths. This is the part of a spec sheet that buyers skip.

A porcelain 4 oz measures 2 7/8 inches across. A melamine 4 oz measures 3 1/4. Another melamine cone is 3 3/8, and one thin plastic cup reaches 4 inches.

Same stated capacity, from 73 to 102 millimetres of rim. A tray that holds twenty of one will not hold twenty of another.

Height barely moves. Most of those models sit between 1 1/2 and 1 3/4 inches deep.

So the extra width was not bought with more depth. It was bought with a more open wall, and an open wall is a different mould.

This is where lids and saucers go wrong. A lid tooled for a 2 7/8 inch rim will not seat on a 3 3/8 inch one, and both are called 4 oz.

It also changes the depth figure in the section after next, because that figure decides which lead limit applies.

Four ramekins drawn to scale from 73 to 102 millimetres rim diameter, all labelled four ounces, with heights shown as equal
One capacity, four footprints. The rim is the number a lid cares about.

Four Bodies, Four Answers

The body decides what the dish can do. A price list rarely says which body you are being quoted for.

Stoneware and ceramic. The retail default. It is heavy, it holds heat, and it survives a water bath. The oven figure has to be asked for.

Porcelain. Denser and harder, so the rim chips less in a busy kitchen. It is the body used for hotelware and for a torch finish.

Borosilicate glass. Clear, so the set can be checked without opening the mould. It takes oven heat and dislikes a sudden cold shock.

Melamine and thin plastic. Cheap, light, and unbreakable in the hand. It has no oven rating at all, for good reason.

Foil. Single use, for a takeaway or a catering line. The cost per piece is tiny and the dish is not a dish afterwards.

BodyOvenTorchWhat to ask for
StonewareYes, with a figureUsuallyThe oven number, glaze on the rim
PorcelainYes, often higherYesRim chip rate, body density
Borosilicate glassYesNo flameShock range, tempered or not
MelamineNoNoMicrowave and wash claim
Aluminium foilYesNoGauge, and a paper lid

One cell in that table is worth a sentence. A glass dish can take 200 °C in an oven and still crack when it lands on a wet board.

That is not a fault in the glass. It is a temperature step in a short time, and every body has a limit on it.

The Twenty-Five Millimetre Line

Here is the number almost nobody puts on a page. The lead limit for ceramic ware is set by the internal depth of the piece.

The US guidance is CPG 545.450. At 25 millimetres of internal depth or less, a piece counts as flatware. Above it, it is hollowware.

Flatware is allowed 3.0 micrograms of lead per millilitre of leaching solution, averaged over six pieces. Small hollowware is allowed 2.0, on any one of six pieces.

A ramekin clears that line without effort. The shallow 4 oz models are about 38 millimetres deep, so the stricter figure applies to every one of them.

The methods are named in the same document: ASTM C738 and two AOAC methods, 973.32 and 973.82.

The European rule splits the same way, on the same measurement. Directive 84/500/EEC puts a fillable article at or below 25 millimetres in Category 1.

Category 1 allows 0.8 milligrams of lead per square decimetre of glaze and 0.07 of cadmium. Every other fillable article is Category 2, at 4.0 milligrams per litre and 0.3.

Then comes the column that decides a bakeware argument. Category 3 covers cooking ware, plus storage vessels above three litres, at 1.5 milligrams per litre of lead and 0.1 of cadmium.

A dish sold to bake in is cooking ware. The same shape sold to serve in is Category 2. The lead limit moves from 4.0 to 1.5, which is close to three times stricter.

So the description on the box changes the limit a laboratory applies. It is worth settling before a sample is sent, not after a report is paid for.

The test is fixed either way. Four percent acetic acid at 22 degrees Celsius for 24 hours, with cadmium read in the dark.

Look at what is missing from that list: heat. The dish is never taken to oven temperature during a food-contact test.

An oven rating and a food-contact result are two separate claims. A listing that shows one of them is silent on the other.

There is also a tolerance clause. A piece up to 50 percent over the limit can still pass, if three more of the same shape average under it.

None of them may be over by more than 50 percent. So the report should name the category, the figure and how many pieces were tested.

A line that says the goods meet FDA and LFGB tells you none of those three. Ask for the page instead of the sentence.

Diagram of a ramekin cross-section at 38 millimetres depth, sitting above the 25 millimetre line, with the US and EU lead limits for each side
One measurement, two rule books. A ramekin is always on the strict side.

What An Oven Rating Has To Say

Oven safe with no figure next to it is a wish, not a rating. The number is the whole value of the claim.

One porcelain 4 oz carries 450 °F. The same shape from another brand prints nothing at all, and the buyer is left to guess.

Three things belong beside the number. Is it heat from above, or a full oven soak? Does a lid change it? Can the dish go under a broiler?

The last one is a different test. A broiler puts radiant heat on the surface for minutes, and a rim can reach a temperature the oven air never did.

The most common failure is not heat. It is a temperature step. A dish leaves a cold fridge and lands in a hot oven, or a hot dish lands on a wet board.

A water bath is the gentle version of that. The dish sits in hot water while the oven heats the air, so the wall sees a slow ramp rather than a jump.

Agree the step in writing. Something like: from 5 °C to 200 °C, no cracks, three pieces, one cycle.

That sentence is testable. Oven safe on a box is not, and a claim that cannot be tested cannot be refused at goods-in.

The Dishwasher Claim

Dishwasher safe is the other claim that arrives without a figure. It has a standard behind it, and the standard is a count.

EN 12875 Part 1 covers ceramic, glass, glass ceramic, vitreous enamel, metal and plastics. It is written for domestic articles, not for a commercial flight.

One cycle copies a household machine: a pre-wash, an alkaline wash, an intermediate rinse, a final rinse with a rinse agent, then a dry.

After the cycles, samples are checked against the original for any visible change. Gloss loss, cloudiness and colour shift are what the check is looking for.

Labs quote 125, 250 or 500 cycles, and ask for four pieces per style with one kept as a control.

A hundred and twenty-five cycles is roughly four months of daily washing. Five hundred is more than a year, which is why the figure has to sit next to the word safe.

Crazing is the reason. Fine cracks in the glaze can appear weeks after delivery, and a sample inspected on the day of packing will not show them.

Decoration is the second half of the claim. A glaze decoration under the surface survives far better than a print sitting over the glaze.

A metallic rim is a third case. It looks right on a table and it is the wrong choice for a dish that will be reheated.

Where The Price Moves At 500 Pieces

A working minimum on a custom order is 500 pieces. One factory in Chaozhou publishes that figure and lists colour, size, logo and packing as the custom options.

Five hundred is small for a ceramic run. The price per piece at that level is driven by fixed costs, not by material.

The mould. A shape needs a mould set, and a set of four sizes needs four. The mould is paid once and spread across the run, so 500 pieces carry it five times harder than 2,500.

The body. Stoneware and porcelain cost more per kilo than melamine. Weight is also freight, and a heavy dish shipped by air can cost more to move than to make.

The decoration. Each printed pass or glaze colour adds a firing and a reject rate. Ask how many passes the quote includes.

The packing. The same factory lists bulk, foam box and brown box. A brown box is cheap. A printed colour box is a different order with a different minimum.

That last point catches more first orders than any other. The dish can start at 500. A printed box usually cannot, so the box minimum can become the order minimum.

If the brief needs a colour box at 500 pieces, plan for a plain box with a label. The other route is to buy the box separately and pack locally.

The grade split. This is the least visible line in a tableware quote. A price can assume that a share of the run sells as second grade.

Ask what share may fall to second grade and where those pieces go. A supplier who will not answer has answered.

The range around the dish matters too. A tray, a lid or a saucer is a second mould and a second minimum. So the bakeware range around it can decide whether a small run works at all.

Six Lines For The Order Sheet

The point of these lines is to turn a word into a figure. Each one closes a gap the name leaves open.

One. Capacity and rim diameter, both written down. A size in ounces alone has no footprint.

Two. Depth, measured inside. It decides the food-contact category, and it is not on most quotes.

Three. The body and the oven figure, with the broiler question answered yes or no.

Four. The dishwasher claim as a cycle count, not as a word. One hundred and twenty-five is a fair floor for a retail line.

Five. Case pack, inner pack and the box. Say whether the colour box is printed or plain, and who prints it.

Six. The grade split, plus the drop test and the carton spec that go with it.

Line two is the one to fight for. Everything else can be settled with a photo and a sample, but the depth decides which limit a lab applies.

A glass body is worth a note here as well, because borosilicate glass takes an oven step that soda-lime glass does not. The two are sold as the same clear dish.

All six lines fit on one page of written figures. A figure is what a factory can build against and what a third party can check.

Then let someone independent look, with those lines on the list. The inspection that catches it before the carton is cheaper than a return.

The food-contact report belongs on the same page. What a kitchenware surface has to meet sets out the rest of it.

DEPTH AND LIMIT

Send me a ramekin quotation, a sample report or the spec sheet from a factory. I will check the rim diameter, the internal depth and which food-contact category the test was run against. I will also say whether the colour box minimum and the dish minimum can both be met on one order. No cost, no obligation.

Check My Spec

Questions Buyers Ask

What is a ramekin used for?

One portion, baked and served in the same dish. Custards, soufflés, baked eggs and small gratins are the classic uses. The foodservice version holds sauce, dip or olives.

What size is a standard ramekin?

Six ounces is the usual retail size, about 177 millilitres. Commercial kitchens work smaller, and 4 oz is the size most often bought by the dozen.

Is a ramekin the same as a soufflé dish?

For one portion, often yes. A soufflé dish also comes in larger sizes for a shared dish, with taller sides to support the rise. The small ones are used as ramekins.

Can a ramekin go in the oven?

Ceramic, porcelain and borosilicate versions can, at a stated temperature. Melamine cannot, and most melamine listings say no oven and no microwave. Ask for the figure, not the word.

Why does the depth matter?

Because both the US lead guidance and EU Directive 84/500 divide ceramic ware at 25 millimetres of internal depth. A ramekin is always deeper than that, so the stricter limit applies.

What is the smallest order for a custom ramekin?

Five hundred pieces is a published factory minimum, with colour, logo and packing as options. A printed colour box usually needs more, so confirm both minimums before you pay a deposit.

Questions & Comments

We read every one and reply within 24 hours

If a ramekin quotation or a sample report crosses your desk, send it over. I will look for the rim diameter, the internal depth and the category the test ran against.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x