18/8 vs 18/10 Stainless Steel: Same Alloy, Two Labels
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

18/8 vs 18/10 Stainless Steel: The Two Points You Pay For

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 11, 2026 · 10 min read

18/8 and 18/10 are the same alloy. Both are 304 stainless steel.

The numbers are a claim about nickel, not a separate grade. The standard allows a nickel range wide enough to hold both labels.

So the question is not which material is better. It is what two percentage points of nickel cost you, and whether the goods really contain them.

This article does the arithmetic, then turns it into six lines for an order sheet and one test that catches a substitution.

Studio still life of stainless steel flatware beside a brushed steel sheet sample on a beige surface
Two labels, one alloy, and a certificate in the middle.

Same Alloy, Two Labels

304 is the most common stainless steel in the world. It is austenitic, which means it is not magnetic and it cannot be hardened by heat.

The trade names for it are 18/8 and 18/10. Standard references list both together as the commercial names used in tableware and fasteners.

Wikipedia’s entry for the alloy is where the search term “18/10” redirects. That redirect is the shortest proof that the two labels are one material.

What differs is how much nickel the mill put in. Chromium stays at eighteen percent either way, and chromium is what makes the steel stainless.

Nickel does a different job. It holds the structure stable, which is why the alloy is tough, ductile and non-magnetic.

Above a certain nickel content the structure stays put. Below it, part of the structure can turn magnetic and harder, and the part is harder to draw.

That is the real difference. Not two materials, but two positions inside one specification.

What The Standard Actually Allows

The sheet gives a range, not a point. For 304 the published range for nickel is wide, and that is where the whole argument lives.

Under AShM A276, the composition table reads chromium 18.0 to 20.0 percent and nickel 8.0 to 11.0 percent, with carbon capped at 0.08.

Read that again with a purchase order in mind. A heat at 8.2 percent nickel is a valid 304. So is a heat at 10.4 percent.

Both can be shipped against a drawing that says “304” and nothing else. Both will pass a certificate check.

Now put the labels back on. 18/8 sits at the bottom of that range. 18/10 sits near the middle. Neither is a separate specification.

No standard defines 18/10 as ten percent nickel. It is a trade description, so it cannot be tested the way a grade can.

The same page carries a second trap worth knowing. Carbon separates 304 from 304L, at 0.08 against 0.035 percent, and that is a separate line on the same certificate.

Bar showing the 304 nickel range from 8.0 to 11.0 percent, with 18/8 at the bottom, 18/10 near the middle, and the whole range inside one specification
Both labels sit inside one permitted range.

So a certificate is not the end of the conversation. It is the start of a narrower question: which number inside the range did you buy?

Two Points, Twenty Kilos

The cost argument is easy to state once the range is clear. Two percentage points of nickel on a tonne of steel is twenty kilograms of nickel.

That is the entire material difference. Everything else in the alloy is held constant by the specification.

Nickel is the expensive element in the mix. So the price gap between an 18/8 heat and an 18/10 heat follows the nickel price, and it moves when that price moves.

This is why a quotation that was right last quarter can be wrong this one. The mill surcharge tracks the metal, not the label.

Per piece, the number looks small. Take a fork at about sixty grams, as an example, and a thousand of them is sixty kilograms of steel.

Two percent of that is 1.2 kilograms of nickel. Small per order, and very visible per container.

The point is not that the money is large. The point is that the money is calculable, which means the price gap can be checked against the label.

If a quote for 18/10 lands at the same number as 18/8, one of three things happened. The nickel is there and the margin is thin. The nickel is not there. Or the 18/8 price was padded.

Before any of that, check the gauge. Thickness and finish usually move a price further than two points of nickel do.

A part quoted in 0.8 millimetre steel and a part quoted in 1.0 are not the same product. Comparing them by grade tells you nothing.

So normalise first: same thickness, same finish, same certificate type. Then the gap that is left belongs to the nickel, and it can be read against twenty kilos a tonne.

What The Extra Nickel Does In Use

Nickel is an austenite former. More of it holds the structure stable through forming, and that is where the practical difference starts.

Stability matters most when the part is drawn or stretched. A stable structure flows instead of cracking, which is why a deep body or a thin bowl is easier to make from a richer heat.

It also survives cold work better. 304 cannot be heat treated, so it is strengthened only by working it, and its tensile strength spans a wide band as a result.

The published range runs from about 210 to 1,050 megapascals. That spread is the material telling you how much the forming operation changes it.

Then there is the surface. A part that takes a mirror polish needs a clean, even structure underneath, or the polish highlights the difference.

The standard reference puts a number on nickel’s corrosion role. It lists nickel at at least 8 percent among the ways to raise resistance, beside more chromium and added molybdenum.

That figure matters for this decision. 18/8 already sits on it, so in that one mechanism the eighth percent and the tenth percent do the same work.

None of that is a corrosion story, and this is where most product pages overreach.

Two points of nickel do not make a part dishwasher-proof. Both labels are 304, and 304 has one chloride limit, not two.

The published figures are about 400 milligrams per litre of chloride at room temperature, falling to about 150 at 60 degrees. Above that it pits.

It is also prone to stress cracking above roughly 60 degrees. Hot, salty water is exactly the environment that finds both weaknesses.

So the extra nickel buys forming behaviour and finish. It does not buy resistance to a dishwasher tab, and no certificate will make it.

Where chloride resistance genuinely has to rise, the answer is a different alloy. The upgrade adds molybdenum, and costs well beyond two points of nickel.

Which Product Gets Which Grade

The decision is per product, not per factory. What follows is how the two labels usually land in a home and daily range.

ProductWhat to orderWhyWhere it goes wrong
Flatware, forks and spoons18/10, nickel range writtenThe label is the selling line and the polish shows18/8 shipped as 18/10, both valid 304
Cookware bodies18/8 with a draw testForming behaviour matters more than the labelPaying a premium for a label nobody can see
Canisters, tools, handles18/8No deep draw, no mirror finishOver-specifying and losing the order on price
Sinks and deep drawsLow-carbon 304, often 304LCarbon control survives the draw and the weldCarbon left out of the drawing entirely
Trays and chafing dishes18/10 where lustre sellsVisible surface, premium shelfPolish specified, nickel left open
Vacuum flask liners18/8, 304L for the weldWelded, not polishedNickel money spent on a hidden part
Knife bladesNot 304 at allBlades need a hardenable steelThe whole family spec’d as one grade

The last row is the one that breaks a bill of materials. A cutlery set is not one steel, and the blade half is a different family entirely.

The comparison of blade steels covers that side, and it is worth reading before a mixed set is quoted as one material.

The Label Is A Claim, Not A Test

Here is the part that costs buyers money. Nothing in the chain forces the label and the heat to match.

A mill pours a heat at 8.4 percent nickel. It is 304, so the certificate is honest and the paperwork is clean.

The parts are made, polished and packed. The box says 18/10, because 18/10 is a trade description with no test behind it.

Every document in that chain is true. Only the box is wrong, and the box is the only one the customer reads.

This is not a rare failure. It is the natural outcome of a specification that permits the range and a label that pretends to a point.

The money explains the motive. Two points of nickel is real cost per tonne. A supplier who shaves them keeps the difference, and the goods still pass any check written loosely.

Diagram of one tonne of 304 with twenty kilograms of nickel highlighted, and the same sum worked for a thousand forks
Twenty kilos a tonne, and 1.2 kilos in a thousand forks.

There is a mirror image of the same problem. A buyer who pays for 18/10 and then hides the nickel inside the product has bought a certificate, not a benefit.

Both failures come from the same place. The order named a label instead of a number.

Heat Number, Certificate, And The Surface Trap

Once the order names a number, checking it becomes a process rather than an argument. Four steps cover most of it.

One. Ask for the heat number. A heat is one pour from one furnace, and every part made from it carries that identity.

Without a heat number, the paper describes a delivery. With one, it describes the steel in the box.

Two. Specify the certificate type. An inspection report at the 3.1 level is issued by an inspector independent of the mill. A 2.2 report is the mill’s own declaration.

The difference is not paperwork. It decides who signs the nickel figure, and whether that signature survives a dispute.

Three. Read the actual number. Not the grade box, the nickel line. A certificate reading 8.4 percent is a valid 304 and an invalid 18/10 claim.

Four. Know what a handheld analyser can settle. A handheld X-ray analyser reads the surface of a finished part. Polished parts read cleanly enough for a grade check.

What it cannot do is settle a two-point argument alone. Ask the lab for its margin, then decide whether that margin fits the question.

On a disputed figure, a laboratory method such as spark emission is the reference. It is worth the fee when the order is a container.

One myth to drop while you are there. Weight will not separate them.

Density sits between about 7.5 and 8.0 across stainless alloys. Two points of nickel moves it by a fraction of a percent.

A scale cannot find that. Anyone who tells you 18/10 feels heavier is describing the finish, not the density.

Six Lines For The Order Sheet

The point of these lines is to turn a label into a number. Each one closes a gap.

One. The alloy and the nickel range: “304, nickel 10.0 to 10.5 percent”. A range, not a label.

Two. The certificate: inspection certificate 3.1 from an independent inspector, quoted by heat number, and the heat number printed on the packing list.

Three. The carbon line, if the part is drawn or welded. That is where 304 and 304L part company.

Four. The test method and the margin accepted as a pass. Otherwise a lab result becomes a negotiation.

Five. The finish, in words that can be seen. Nickel is partly bought for lustre, so the polish belongs in the same document.

Six. The substitution rule: no change to nickel content without written approval, whatever the certificate would still allow.

Those six fit on one page, and they replace the sentence that causes the trouble. A sheet the factory has to build against is the format that makes them stick.

The rest of the chain looks the same way. Walking the line during an audit is where you see whether the heat number on the box matches the one in the file.

And the material half of the question is already written up. The composition behind the 18/10 label covers chromium, nickel and the grades around them; this page is about the choice and the money.

What The Words Mean

Most of the confusion is a trade description doing the work of a specification.

What it saysWhat it actually isWhat to ask
“18/10”A nickel claim with no standard behind itWhat nickel range is on the certificate?
“304 stainless”The alloy, with the full 8.0 to 11.0 rangeWhich number inside that range?
“18/10 is heavier”A myth about densityWeigh it: the difference is a fraction of a percent
“Dishwasher safe”A claim about a wash cycleChloride level and temperature of that cycle?
“Surgical steel”No defined gradeWhich alloy, by its standard number?
“Food grade 304”An alloy plus a declarationWhich test, and who signed it?

Every line there is shorthand for something a certificate can state precisely. The document is what survives the argument.

GRADE CHECK

Send me the specification sheet or the mill certificate for a stainless product you are buying. I will check whether the nickel range is written down, whether the certificate type is worth anything, and where the label is doing work the document should be doing. No cost, no obligation.

Check My Certificate

Questions Buyers Ask

Is 18/10 better than 18/8?

For forming and for a mirror polish, often yes. For corrosion in a dishwasher, no: both are 304, and the chloride limit is a property of the alloy rather than of the nickel count.

Are they really the same alloy?

Yes. Both are commercial names for 304, and the standard entry for 304 is where the search term 18/10 redirects. The difference is where each sits inside the permitted nickel range.

Can I tell them apart with a magnet?

No. Annealed 304 is essentially non-magnetic either way, and cold working or a cut edge can make a magnetic spot appear on both. A magnet sorts 304 from a ferritic grade, not 18/8 from 18/10.

Does 18/10 mean ten percent nickel?

Only as a trade claim. No standard defines the label, so the number on the box is a description and the number on the certificate is the fact.

What is a 3.1 certificate?

An inspection document issued by an inspector independent of the mill, as opposed to the mill’s own declaration. It is the version that carries weight when the nickel figure is disputed.

Why does the same product rust in one kitchen and not another?

Chlorides and heat. 304 tolerates roughly 400 milligrams per litre of chloride at room temperature and about 150 at 60 degrees, so a hot salty wash finds the limit that a cool rinse never reaches.

Questions & Comments

We read every one and reply within 24 hours

If your flatware or cookware sheet says 18/10 and nothing else, send it. I will read the nickel line on the certificate and tell you what the label is worth.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x