HDMI vs DisplayPort: Which One Charges You per Unit
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

HDMI vs DisplayPort: Bandwidth, Cables and the Fee Behind Each Port

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao
· Updated November 5, 2026 · 11 min read

Both ports carry a picture. Neither is better at colour. The real split is three things. How much data the link can move. How many screens one port can drive. And who pays a fee for every unit that leaves the factory.

Buyers send me this question as a picture problem. They want to know which one looks sharper. Once you price a monitor or a dock, the question changes shape. One of these interfaces carries a per-unit charge. The other does not.

That single line decides more designs than any refresh rate.

Warm beige studio still life of an HDMI plug and a DisplayPort plug lying side by side
Two shapes, two owners. One of them bills you for each device.

Two Interfaces, Two Owners

HDMI is a brand. It was designed in December 2002 by a group of consumer electronics firms, and the HDMI Forum has run the specification since October 2011. The connector has nineteen pins. The interface ships in enormous volume: close to fourteen billion devices had been sold by January 2026.

DisplayPort comes from VESA, the monitor standards body. Version 1.0 was approved in May 2006, and products arrived in 2008. It uses twenty pins and a packet link, much like the way data moves on a network.

The mechanical difference is small. The ownership difference is not. HDMI is licensed to adopters under an agreement with a fee attached. DisplayPort is published by a membership body that says it charges no per-device fee.

Neither one is an open standard in the strict sense. Both need a licence or a membership to build against. The question for a buyer is where the money leaves, not whether it does.

What the Cable Actually Carries

Older HDMI sends video over three data lanes plus a separate clock lane. That scheme is called TMDS. It worked well for years and it ran out of room at 18 Gbit/s.

HDMI 2.1 replaced it with a scheme called Fixed Rate Link. FRL uses four data lanes and folds the clock into the data. That change is what let the interface move from 18 to 48 Gbit/s.

DisplayPort took the packet route from the start. It runs one, two or four lanes, and it carries a separate auxiliary channel for control. From version 1.2 that channel widened from 1 Mbit/s to 720 Mbit/s.

That control channel does more than handshake. It carries the display identity data and the control set the monitor understands. It is how a screen reports the modes it supports, and how software changes brightness without touching the video stream.

The choice has a practical result. A packet link can carry several independent streams and can give up lanes when it shares a cable with other data. A link built to carry one video stream stays one stream.

The Bandwidth Ladder

Numbers settle most of this argument. The table below is the current state of both standards. Every figure comes from the published HDMI revisions and the VESA revisions.

VersionRaw rateHow it movesWhat it is for
HDMI 2.018 Gbit/sTMDS, 3 lanes at 6 Gbit/s4K at 60 Hz
HDMI 2.148 Gbit/sFRL, 4 lanes8K near 50 Hz, 4K high refresh
HDMI 2.296 Gbit/sFRL, 4 lanesReleased June 2025, adds latency signalling
DisplayPort 1.432.4 Gbit/sHBR3, 4 lanes at 8.1 Gbit/s4K at 120 Hz, 8K at 30 Hz
DisplayPort 2.0 / 2.180 Gbit/sUHBR20, 4 lanes at 20 Gbit/s8K at 60 Hz without compression

Two footnotes matter for a spec sheet. DisplayPort 1.4 spends part of its raw rate on encoding, so the usable figure is 25.92 Gbit/s. DisplayPort 2.0 lifted the usable rate to about 77.37 Gbit/s, roughly three times the older link.

The ladder also hides a trap. HDMI 2.1 has three rate tiers in practice, and a port can carry the name without the top tier. Always ask for the rate in Gbit/s and write that number into the order, not the version label.

The other trap sits in the cable. A 48 Gbit/s port with a 10 Gbit/s cable is a 10 Gbit/s product that says 2.1 on the box. The cable sourcing guide covers how that grade is ordered.

Infographic comparing HDMI and DisplayPort bandwidth across generations
The same chassis can hide a 10 Gbit/s link. The version label will not tell you which.

One Port, Several Screens

DisplayPort 1.2 added multi-stream transport in January 2010. One connector can carry several independent video streams, so a monitor can daisy-chain another monitor behind it.

This is why office docks look the way they do. A single DisplayPort or USB-C link reaches the dock. The dock splits it into two or three screens without a second cable back to the laptop.

HDMI never added an equivalent. A link carries one video stream. A dock that drives two screens from one HDMI output splits and re-times the picture inside the box. That costs a chip and adds a failure point.

For a single-screen TV this changes nothing. For a two-screen desk it decides the architecture before the industrial design starts.

The Licence Line in a Bill of Materials

Here is the part that rarely appears in a comparison article, and the part that changes a quotation. HDMI is licensed. DisplayPort is published by a membership body.

The HDMI adopter agreement has two annual structures. A high-volume adopter pays US$10,000 a year. A low-volume adopter pays US$5,000 a year plus a flat US$1 per unit administration fee for ten thousand units or fewer.

On top of that sits a per-unit royalty. The base rate is US$0.15 per device. It drops to US$0.05 when the HDMI logo appears on the product and its marketing. It drops again to US$0.04 when HDCP is implemented and the logo is used.

The royalty is charged per device, not per port. A TV with four HDMI sockets pays once. It is only charged on products sold on a stand-alone basis, not on a component that goes inside another licensed product.

DisplayPort works the other way. VESA states that it charges no per-device or per-port fee, and that position held as of 2025. A company still needs membership to reach the specification, at a minimum of US$5,000 a year, or US$10,000 depending on annual sales.

One complication is worth knowing. A patent pool has claimed a US$0.20 per-device royalty on DisplayPort products, and VESA has disputed that claim. Treat the claim as a risk to check with your own counsel, not as a settled cost.

Cost lineHDMIDisplayPort
Annual feeUS$10,000 high volume, or US$5,000 low volumeUS$5,000 to US$10,000 membership
AdministrationUS$1 per unit on the low-volume agreementNone stated
Per-unit royaltyUS$0.15 base, US$0.05 with logo, US$0.04 with HDCP and logoNone charged by the standards body
Charged perDevice, not per portNot applicable
Disputed claimNoneUS$0.20 per device claimed by a patent pool

Put the two together and the shape of the decision appears. Fifty thousand units with the logo and HDCP cost US$10,000 plus fifty thousand times US$0.04, which is US$12,000, or US$0.24 a unit.

Now try five thousand units. The low-volume route costs US$5,000 plus five thousand times US$1, which is US$10,000, or US$2.00 a unit. A small run pays eight times more per device than a large one.

That is the whole argument for a DisplayPort-only product at low volume. The saving is not in the connector. It is in the agreement.

None of this is a reason to avoid HDMI. A product that must plug into a TV has to carry it. The point is that the fee belongs in the costing sheet at quotation time, not in a surprise at the end of the year. The six-line spec sheet I use has a row for licence ownership for exactly this reason.

Infographic comparing the per-unit licence cost of HDMI and DisplayPort
The same royalty is 24 cents a unit at fifty thousand and two dollars at five thousand.

Certified Cables and How Far They Reach

Both standards certify cable grades, and the grades are where most product failures start. A port that meets a specification is not the same as a cable that can feed it.

On the HDMI side the useful grade is Ultra High Speed, certified at 48.0 Gbit/s. That is the cable rated for 4K at 144 Hz with high dynamic range. Standard HDMI cable is certified at 2.2275 Gbit/s, which is enough for 720p at 60 Hz.

DisplayPort 2.1 certifies cables as DP40, DP54 and DP80, matching the three newer link rates. A later revision added a low-loss active cable, DP80LL. It reaches three metres at the full 80 Gbit/s, about three times the reach of a passive certified cable.

HDMI sets no maximum length in the specification. In practice the limit is attenuation, and a longer run needs a heavier conductor or an active cable. Ask the factory which grade and which length it tested, not whether the cable works.

A passive copper cable carries the signal until loss eats it. Past that point the options are a heavier conductor, an active cable with a chip inside, or an optical run. Each one changes the landed cost and the way the cable fails, so the length belongs in the drawing beside the grade.

Electrical testing catches the rest. The electrical testing route for a finished device covers the port alongside the rest of the board.

Cable builders sit in the same districts as the connector makers. Where those parts change hands is its own trip, and the Shenzhen components market is the short version of it.

Where HDMI Still Wins

Three things keep HDMI on almost every bill of materials.

The first is the installed base. Close to fourteen billion devices carry the port, and a TV without one is unsellable in most markets.

The second is audio. The enhanced audio return channel lets a TV send high-quality audio back down the same cable to a soundbar or receiver. That path exists because the TV is the hub, which is how living rooms are wired.

The third is control. The consumer electronics control line lets one remote switch on the TV, the player and the amplifier together. It is unglamorous and buyers notice when it is missing.

None of these are bandwidth features. They are living-room features, and they explain why a product with a DisplayPort output still often ships with an HDMI port beside it.

Six Lines a Port Spec Must Carry

A factory will build whatever the drawing shows. The drawing usually shows a connector and a version number, and a version number is not a specification.

These six lines close the gap between a port that works on a bench and a product that survives a return rate.

  1. Rate in Gbit/s. Write 18, 48 or 96 for HDMI, and 32.4 or 80 for DisplayPort. The version label alone allows several rates.
  2. Lane count at the connector. Four lanes is not automatic. A dock running video beside USB data may only get two.
  3. Certified cable grade. Ultra High Speed for 48 Gbit/s HDMI, or DP40, DP54 and DP80 on the DisplayPort side.
  4. Feature set. State whether you need the audio return channel, multi-stream, compression or adaptive sync. Each one changes the chip.
  5. Licence owner. Name who signs the adopter agreement and who pays the per-unit fee. Put it in writing before the mould is cut.
  6. Acceptance test. Define the resolution and refresh rate the unit must hold for an hour, and the cable you will test with.

Line five is the one buyers forget, and it is the one that arrives as an invoice rather than a defect.

The Short Version

Pick DisplayPort when one port must drive several screens. Pick it when the product lives on a desk, or when the volume is small enough that the per-unit fee hurts.

Pick HDMI when the product must meet a TV, a console or a soundbar, and when the remote has to switch the whole room on.

Ship both when the product sits between those two worlds. A dock with one of each costs a port and saves an adapter, and the installed base justifies it.

Then write the rate, the cable grade and the licence owner into the order. Those three lines decide whether the port you paid for is the port that ships.

PORT SPEC

A Version Label Is Not a Rate

Send me the ports on your drawing and the resolution the product must hold. I will tell you which link rate that needs and which cable grade reaches it. I will also say whether the licence sits with your supplier or with you. That answer is cheaper before the tooling than after the first shipment.

Send the Port List
Is DisplayPort better than HDMI?

Neither one wins across the board. DisplayPort has more headroom per link and can drive several screens from a single connector. HDMI fits TVs, consoles and home audio. The answer follows the device you must plug into, not the specification sheet.

Do I need an expensive cable for 4K?

You need a certified grade, not a price. For 48 Gbit/s HDMI look for Ultra High Speed. For the newer DisplayPort rates look for DP40, DP54 or DP80. An uncertified cable often works on the bench and fails in the field.

Can I convert one interface into the other?

Yes, with the right adapter. DisplayPort has been required to support dual-mode since version 1.3, so it can drive an HDMI display directly. Going the other way needs an active converter, and features such as multi-stream are lost on the way.

Why does my dock carry both ports?

Because the installed base is split. An office desk wants DisplayPort for two or three screens and HDMI for the projector in the meeting room. Carrying both costs one connector and removes an adapter from the buyer’s drawer.

Who pays the HDMI royalty, me or the factory?

The adopter who signs the agreement pays, and that is normally the brand that puts the device on the market. If a factory builds a finished product that carries your name, assume the obligation is yours until the supplier shows you otherwise in writing.

Does DisplayPort work over a USB-C port?

Yes. DisplayPort Alt Mode places the video link on the USB-C connector, using two or four lanes. That is how one small port drives a monitor and moves data at the same time.

Questions & Comments

We read every one and reply within 24 hours

A port costs more than the connector. Tell me which screen the product must drive, and I will price the link rate and the licence line before the tooling starts.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x