Cadmium In Jewelry: The 0.01% Rule, Per Part
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Cadmium In Jewelry: The Test That Stops A Shipment

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 17, 2026 · 9 min read

A cadmium problem is not a quality problem. It is a paperwork problem that arrives after the goods are made. A lab report says one clasp on one necklace sits above the line.

The line is 0.01% by weight of the metal, and it applies to each metal part on its own. Not to the necklace as a whole.

That single word — each — is where most shipments fail. A piece can average well under the limit and still be stopped, because one small part was made from the wrong brass.

This page covers four things. The European rule and its date. The parts it covers. The arithmetic that hides a failure, and the test that settles it before the container leaves.

The material side of the same family of questions has its own page. what costume jewelry is made of sets out the base metals. This page stays on the limit and the report.

Cadmium in jewelry cover showing a chain, a clasp and a per-part limit card
The limit does not apply to a piece. It applies to each metal part inside that piece.

The Short Answer

In the European Union, cadmium at or above 0.01% by weight of the metal may not be used in the metal parts of imitation jewellery. That includes beads sold for jewellery making, hair accessories, brooches, cufflinks, wrist-wear and piercing jewellery.

The rule has been in force since 10 January 2012. It came in through Commission Regulation (EU) No 494/2011, which amended entry 23 of Annex XVII to REACH.

Read the limit as a ceiling on every component, not on the finished article. A pendant, a jump ring, a clasp, a post and a chain are five separate parts under this rule.

So the useful question at the sample stage is not “how much cadmium is in this necklace”. It is “which part carries the most, and what is that part made of”.

What The Rule Actually Says

The restriction covers three material groups, and jewellery is only one of them. The other two explain a lot of the failures buyers see on chain.

Group in entry 23What the limit blocksWhere it bites
Metal parts of jewellery0.01% or more by weight of the metal, per partBase metal bodies, clasps, posts, jump rings, beads sold loose
Brazing fillers0.01% or more by weightSolder at joints on chains, bails and pin stems
Plastics0.01% or more by weight of the plasticCoated charms, plastic beads, printed pendants

Two carve-outs sit beside the rule. Jewellery more than 50 years old is treated as antique and left alone. Stock that was already on the market when the ban took effect can keep moving through resale. Neither carve-out helps a new production run.

The scope list is worth reading line by line. It is broader than the way most people use the word jewellery. Hair accessories and wrist-wear sit inside it. So do the metal beads that a factory buys by the bag to solder onto a charm.

The Irish health and safety authority publishes a plain summary of entry 23 in one table. It is easier to send to a factory than the legal text.

That last point catches buyers who think of themselves as sourcing components rather than finished goods. A bag of beads is in scope the moment it is meant for jewellery making.

Where The Rule Lands

The rule lists the goods by type rather than by price. That matters, because buyers often assume the rule follows value: precious on one side, cheap on the other.

It does not. Entry 23 names metal parts of imitation jewellery and hair accessories, then spells out bracelets, necklaces, rings, piercing jewellery, wrist-watches and wrist-wear, brooches and cufflinks.

A gold-plated brass ring and a silver ring with a base metal setting can sit on the same list. The question is which part is base metal, and what is in it.

Scope map of entry 23: covered metal parts, brazing fillers, plastics, and the antique carve-out
Three material groups sit inside the limit. The antique carve-out is the only one a new order can rely on.

The Arithmetic That Hides A Failure

Averages are how this problem survives a factory’s own quality check. Take a necklace of about 40 grams built from a body, a chain, a clasp and two jump rings.

Suppose the clasp is 2 grams and carries cadmium at 0.05% of its own weight. The other 38 grams are clean. The whole piece then averages a small fraction of the limit and passes any check that tests the article as one unit.

The clasp is still five times over the line as a part. That is the version a lab reports, and that is the version an authority acts on.

This is not a hypothetical risk invented for the page. It is the natural result of how jewellery is assembled. The cheapest component is often bought from a different supplier, in a different alloy, with no statement.

Two habits follow from those sums. Ask for a report that lists results part by part. And ask which part was sampled, not just how many pieces were tested.

How Cadmium Gets In

Cadmium does not arrive through a recipe. It arrives with the raw material, and it hides in three places.

The first is scrap metal. Brass is bought by grade, and a cheap grade can carry whatever was melted before it.

Old plating, solder and painted parts all go into the same furnace. The result is an alloy that looks right and reads wrong.

The second is pigment. Some reds, oranges and yellows are built on cadmium compounds, which is why a bright plastic charm deserves its own line on the test request.

The third is recycled plastic. Cadmium was once used to keep PVC stable, and old PVC can carry it into a new mould.

None of this shows in a visual check. A clean part and a loaded part can look the same under a lamp.

Ask for the mill sheet and the alloy name. A photo of the finished piece proves nothing.

Illustration of a necklace averaging under the limit while one clasp sits above it
An illustration of the sums, not a test result: five parts, one clasp above the line, article average below it.

The Joint Nobody Samples

Brazing filler is the second group in the rule, and it explains failures on goods with a clean base metal.

A chain is not made of one metal. The links are joined, and the bail is soldered to the pendant. The pin stem is fixed to the brooch with a filler that melts below the parent metal.

That filler has its own cadmium limit, set at the same 0.01% by weight. It is a separate rule from the metal parts clause, so a supplier can pass one and fail the other.

Cheap fillers are attractive for a reason. They flow at lower temperatures, which protects thin parts from distortion, and they cost less than the alternatives.

The practical result is a necklace whose body and chain both test clean. The joints test high. A sample cut from the middle of a link will miss it entirely.

So the sampling instruction has to name the joint. Ask for the solder area, the bail, and the point where the pin meets the frame.

Plastics And The Painted Parts

The third group is plastics, and its limit is measured against the weight of the plastic rather than the weight of the metal.

This catches coated charms, printed pendants, plastic beads and the enamel or resin fills that sit above a metal frame. A clean metal body does not clean the coating on it.

Hair accessories appear in the same entry, which surprises buyers who run a jewellery line and a hair line from one factory.

If the two lines share a component bin, one contaminated batch can put both under the same question.

What The United States Stops You On

The American route to a stopped shipment runs through lead, not cadmium, and the number is written into statute.

For children’s products, total lead content is limited to 100 parts per million by weight under 15 U.S.C. 1278a. The same section is blunt about coatings: paint, coatings and electroplating may not be treated as a barrier.

That sentence removes a common defence. A plated brass part does not become a clean part because the surface is covered.

For cadmium itself, this page quotes no American figure, because there is no single federal number that plays the role the European 0.01% plays. If a buyer’s rule sheet names one, ask for the clause in writing and test to that clause.

When the destination is mixed, the safe habit is the stricter of the two. A part built for the European limit will usually satisfy a lead-driven review, while the reverse is not true.

Base metal choice drives most of this, and what brass jewelry contains explains why the same alloy name covers a wide range of scrap content.

The Test That Settles It

Two tests get called “the cadmium test” in supplier conversations, and they answer different questions. Mixing them up is how a clean report arrives for a part that is not clean.

The first is X-ray fluorescence, usually shortened to XRF. It is fast, it does not damage the sample, and it is good at telling you which parts deserve attention.

It is also a surface measurement. A plated part reports on the plating, and a lacquered part reports on the lacquer. That makes it a screening tool, not a verdict.

The second is acid digestion. The sample is dissolved, so the number covers the whole mass of the part. A lab machine then reads the liquid. The method is usually called ICP.

That is the number a regulator will act on, because total content is what entry 23 limits. Ask for this method by name when the destination is the European Union.

Test ladder: XRF screening, acid digestion confirmation, and a per-part report
Screen with XRF, decide with digestion. A report that does not name the method cannot settle a dispute.

What The Report Has To Say

A report can be genuine and still useless. Five fields decide whether it can defend a shipment.

FieldWhy it matters
Part-level resultsEntry 23 applies per metal part; a single article average cannot show that
Method namedXRF and digestion answer different questions; the clause names total content
UnitsPercent by weight is the language of the rule; mg/kg needs a conversion on the page
Sample identityWhich colour, which supplier, which batch; a report without a batch cannot be matched to goods
Date and labA report older than the alloy change proves nothing about the current run

The trap is a report that lists one line for the whole necklace. It looks tidy, it passes a quick read, and it cannot show the one part that fails.

When a supplier sends a certificate instead of a report, treat it as a claim rather than evidence. A certificate says a system exists. A report says what this batch contains.

Six Lines For The Order

These six lines move the problem to the sample stage, where a failure costs a remake instead of a container.

#Line to writeWhat it prevents
1Cadmium below 0.01% by weight in every metal partAn average that hides one bad clasp
2Brazing filler named, with its own cadmium statementA clean body with a failing joint
3Plastic and coating parts listed separatelyA clean metal frame with a loaded coating
4Acid digestion per part, method named on the reportAn XRF screen passed off as a verdict
5Report tied to a batch, a colour and a supplierA test that cannot be matched to the goods
6Lead statement for children’s lines, to 100 ppmA US buyer finding the gap at the port

Line four is the one suppliers push back on, because digestion destroys samples and costs more. Pay for it once on the first order and keep the report as the baseline for every repeat.

Line six is where the American rule enters the same document. For children’s goods, the lead limit is a statute, not a guideline. Plating does not shield the part underneath.

The order also needs a name attached to the metal. If the alloy is left as “brass”, the cadmium question stays open. The same word covers recycled content of very different quality. what the 925 stamp covers shows the same logic on the precious side, where the number is fixed but the alloy behind it is not.

Tooling and sampling sit inside the same cost conversation. how a jewelry order is quoted and tooled sets out where those charges land on a first run.

Who This Page Is For

Three readers get something from the page. The first is a buyer placing a first order with a new factory and wondering which document to ask for.

The second is a brand that already has a report and cannot tell whether it proves anything. The five fields above answer that.

The third is a sourcing agent or QC team writing an inspection plan, who needs the sampling points named before the visit rather than after.

CADMIUM CHECK

Send The Part List

Send the bill of materials with each metal part separated. Add the destination market and the alloy your factory quoted. I will mark which parts need their own cadmium line and which joints need the filler named. I will also say whether your report can survive a per-part read.

Check The Part List

Questions Buyers Ask

Is 0.01% measured on the whole piece or on each part?

Each metal part. The Commission confirmed that the level is calculated per component, which is why a per-article average can pass while one part fails.

Does the limit apply to silver and gold jewellery?

The jewellery clause names metal parts of imitation jewellery and hair accessories. Precious metal lines still meet the brazing filler and plastics limits, and many buyers apply the strictest line across the whole range to keep one rule.

Is a certificate from the factory enough?

No. A certificate describes a system. Only a test report tied to a batch says what the goods contain, and only a report that names the method can settle a dispute.

Can we skip digestion and rely on XRF?

XRF is a good screen and a weak verdict, because it reads the surface. A plated or lacquered part can pass a scan and fail on total content.

What about old stock and antiques?

Jewellery more than 50 years old is treated as antique and exempt, and stock already in the market when the ban took effect can keep moving through resale. Neither covers a new production run.

Does the same number apply in the United States?

The American check that stops jewellery shipments is the lead limit for children’s products, set at 100 ppm, and it is written so that plating is not a barrier. If a buyer’s sheet names a cadmium figure, ask for the clause and test to it.

Questions & Comments

We read every one and reply within 24 hours

Which part is base metal, and what does its test report say? Send the part list and the destination market, and I will mark the parts that need their own line and the report fields that are missing.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x