Sterling Silver 925: Where the Alloy Stops Being Sterling
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Sterling Silver? 925, the 7.5%, and Where the Mark Stops

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 16, 2026 · 10 min read

Sterling silver is 92.5% silver by weight. The other 7.5% is another metal, and US law fixes that number at 925 parts per thousand before a seller may use the word.

That is the whole definition. Most pages stop there and move on to polishing cloths.

A buyer cannot stop there. The 7.5% decides how the piece casts, how fast it turns dark, and whether a batch passes a check at customs. The word also carries a tolerance, and the tolerance is where orders go wrong.

This page keeps the definition short. The space goes to the part that costs money. That means what the stamp promises, what it does not, and the six lines to put in the order.

A polished sterling silver ring and a bare silver alloy ingot on a beige studio surface
One is finished sterling. The other is an alloy waiting to be stamped.

The Short Answer

Sterling silver is an alloy of 92.5% silver and 7.5% other metal, usually copper. It is the same thing as 925 silver. Both names mean one number.

The word is not a grade of quality. It is a claim about content, and a seller who uses it is making a statement that can be tested in a lab.

Three facts follow from that, and each one changes an order.

First, the 7.5% is not waste. Pure silver is soft, and a ring made of it bends under daily wear. Copper hardens the alloy, and it also makes the metal easier to cast and to set stones into.

Second, the mix is not fixed. Two factories can both stamp 925 and ship alloys that behave differently. The law sets the silver side of the ratio. The other side stays open.

Third, the stamp can be true and still fail a check. US law allows a small shortfall against 925, and the shortfall doubles when the piece contains solder.

What The 925 Stamp Promises

In the United States, the promise is written in the Federal Trade Commission’s jewelry guides. Section 23.5 covers silver content, and it is short enough to read in full.

The rule that matters most sits in 16 CFR 23.5(b)(2). The words sterling silver, sterling, or the short form Ster. may only mark a product that is at least 925/1,000ths pure silver.

Three neighbours in the same section are worth knowing, because sellers mix them up.

Mark on the pieceWhat the rule requiresRule
sterling silver, sterling, Ster.At least 925/1,000ths pure silver16 CFR 23.5(b)(2)
coin or coin silverAt least 900/1,000ths pure silver16 CFR 23.5(b)(3)
Bare word silverA fineness number must sit right before it, as in 750 silver16 CFR 23.5(b)(1)
Silver plated base metalThe word may be used only with a clear note that the piece is coated16 CFR 23.5(b)(4)

The last row has a harder edge. A plated article may not be stamped sterling or coin at all. That ban comes from the National Stamping Act, and the commission quotes it inside the same section.

This is the first place a sourcing agent earns his fee. A factory that stamps 925 on a brass core with a silver wash is not making a small mistake. It is making goods that cannot be sold with that mark in the United States.

The Tolerance Nobody Quotes

925 sounds like an exact figure. It is not. The National Stamping Act allows a piece to sit slightly under the mark, and the size of that allowance depends on one thing: solder.

For sterling parts that contain no solder, the permitted shortfall is 4 parts per thousand. For parts that contain solder, the permitted shortfall is 10 parts per thousand.

The footnote in the FTC guide states this directly, and it points to the statute at 15 U.S.C. 294 and the sections that follow.

Put in plain terms, a soldered piece may test as low as 915 and still sit inside the allowance. A piece with no solder may test as low as 921.

Buyers who do not know this read a lab report of 917 and reject a shipment that the law would allow. Buyers who do know it ask a better question: where is the solder, and how much of the weight is in it?

That question has a cost answer. A hidden jump ring, a pin finding or a heavy clasp can carry a large share of the total weight. The solder used to join it pulls the assay down. The fix is a design decision, not a production argument.

Two practical moves follow. Put the solder weight in the spec sheet. Test the finished piece, not the sheet metal that came in the door.

Flat diagram showing three silver grades on a 1000-part scale with the 4 and 10 part solder allowances marked
925 is the mark. 921 and 915 are the floors the statute allows.

What The Other 7.5% Does

Copper is the usual partner, and it is there for three reasons. It hardens the metal, it lowers the melting point, and it makes the alloy flow into a mould.

It also brings the weakness. Copper reacts with sulfur in the air, and that reaction is what turns a silver ring dark.

The law does not name the partner. It sets the silver side at 925 and leaves the rest to the mill. Two suppliers can then ship alloys that look identical and age differently.

Some mills add a small amount of another metal to slow the darkening. Others keep the mix simple and sell a plating step instead. Neither choice is wrong, but the two prices are not comparable, and the sheet has to say which one you are getting.

A buyer who wants that difference on paper should ask for three items. Ask for the alloy name the mill uses and the mix it publishes. Ask one more question: bare metal or plated.

Bare metal means the surface is the alloy itself. Plated means a thin layer sits above the metal, and that layer becomes the wear surface. When the layer goes, the colour underneath shows through.

The page on how a PVD coat differs from an electroplated one covers that outer layer in detail. For sterling, the short point is that a plated silver piece has two failure modes, not one.

Where A British Buyer Meets A Different Rule

The United States controls the claim by content. The United Kingdom controls it by an assay office and a stamp, and the duty starts at a weight line.

The Hallmarking Act 1973 sets out which articles must be sent for testing and marking. Schedule 1, Part 2, paragraph 12A holds the exemption. An article is exempt when two conditions hold at once. It must contain silver of minimum fineness. Its total metal weight must be under 7.78 grams.

That single line explains a question that comes up in almost every small silver order. A pair of stud earrings and a fine chain often sit under the line, so they carry a maker’s mark and no assay mark. A bracelet or a cuff usually sits above it and must be hallmarked before it can be described as sterling in trade.

The exemption has three exceptions, and they are worth reading before you plan a shipment. An article loses the exemption if it also contains gold, platinum or palladium at minimum fineness. It loses the exemption if it holds any precious metal below minimum fineness. It also loses it when the article contains material other than precious metal, unless it meets the conditions in Part 3 of Schedule 2.

The third exception is the one that catches mixed pieces. Take a silver pendant on a steel chain. Or a silver bezel set into a base metal frame. Neither one is a simple silver article for this purpose.

Full text sits at the Hallmarking Act 1973 on legislation.gov.uk. Read paragraph 12A and the three exceptions together, because the questions from a UK buyer will land on one of them.

MarketWhat decides the wordWhere the rule lives
United StatesSilver content of the whole piece, with a tolerance for solder16 CFR 23.5 and 15 U.S.C. 294
United KingdomIndependent assay and a stamp, above 7.78 g of metalHallmarking Act 1973, Sch. 1 Pt. 2 para. 12A

Why It Turns Dark, And What That Costs

Tarnish is a surface reaction, not a defect in the metal. Sulfur compounds in the air meet the copper in the alloy, and a dark film forms on the surface.

Three things make it faster. Warm air, high humidity, and packing that traps sulfur. A warehouse near a rubber works or a paper mill will darken stock faster than a dry one.

For a seller, the cost is not the metal. It is the return. A piece that arrives dark reads as old stock. The buyer then asks for a refund on goods that were correct when they left the factory.

Control is cheap and boring. Seal the piece in a bag with an anti-tarnish strip. Keep the cartons off a concrete floor. Ship air freight rather than a slow sea container in a humid month when the order is small.

Plating adds a barrier and one more cost line. It also changes the claim, because a plated piece needs its surface layer disclosed. Section 23.7 of the same part covers rhodium, which is the common finish on white-looking silver.

The Cost Math A Quote Should Show

Silver is priced by weight, and the piece is not pure silver. The first number in any honest quote is the metal inside the piece, and it has one shape.

Take the finished weight, multiply it by 0.925, then multiply by the metal price for the day. That gives the silver value. The working loss, the alloy, the solder, the labour and the finish sit above that figure.

No honest quote can use a price from a page like this one. Metal moves every trading day, and a figure written in an article is stale before it is read. Ask the factory which day’s price it used, and make that date part of the quote.

What a buyer can compare across factories is the part that is not metal. The table below lists those lines, and each one has a way to be checked.

Cost lineWhat moves itHow to check it
Silver valueFinished weight, purity, the price dateWeigh ten pieces, ask for the price date
Working lossFiling, polishing, casting spruesAsk for the loss rate as a percentage
SolderNumber of joins, alloy of the solderCount the joins on the drawing
LabourSetting, hand finish, chain assemblyAsk for the minutes per piece
FinishBare polish, rhodium, e-coatAsk which surface a buyer will touch
TestingAssay per batch, not per pieceAsk for the batch size on the report

Two of those lines carry most of the argument in a price talk. Working loss is the one factories leave vague, because a high number is hard to disprove. Labour is the line buyers underrate. A heavy cast piece and a light hand-finished piece can share a metal cost. They differ by a wide margin on the bench.

Tooling is a separate subject, and it lands on the first order. The page on how a jewelry factory structures a quote covers mould cost, sample cost and the point where a second order gets cheaper.

Six Lines For The Order

Everything above fits into six lines that can be pasted into an order sheet. None of them needs a lawyer, and each one can be checked at the factory by someone holding the piece.

#Line to writeWhat it prevents
1Alloy is 925 silver, and the mill sheet is attachedA copper mix that darkens in weeks
2Finished weight per piece, with a stated toleranceMetal paid for and not delivered
3Solder joins are counted and the solder alloy is namedAn assay that lands under the allowance
4Surface is bare metal or the plating is named and measuredA claim that hides a coated core
5Assay test per shipment, on a named batch sizeA single test covering goods it never saw
6Mark applied: 925, sterling, or both, plus country of originA stamp the destination market does not allow

Line three is the one that pays for itself. Ask for the join count before the mould is cut. A design with six joins and a design with one join can look the same on a screen and behave very differently in a lab.

Line four is the one that saves a whole shipment. A rhodium finish over sterling is legal and common. A silver wash over brass is not sterling, and no amount of polishing makes it one.

Line six depends on where the goods are sold. In the United States the mark follows the content rule. In the United Kingdom the piece above the weight line needs an assay mark from an office, and the importer carries the duty.

One more habit helps. Photograph the stamp on the first article, at ten times, and keep the photo with the shipment file. A dispute about a mark is easy to settle with a picture and hard to settle with a memory.

Flat checklist diagram listing six order lines for sterling silver sourcing with tick marks
Six lines. Each one is checkable at the factory door.

Who This Page Is For, And Who It Is Not

This page is for the buyer who is about to place a silver order and wants the claims on the sheet to hold up. It is not a guide to antique silver, silver plate collecting, or the care of inherited pieces.

A few hundred pieces of small silver is the common case. The weight line in the British rule and the solder allowance in the American rule decide whether those goods arrive clean.

Some orders mix silver with steel, brass or a plated frame. Treat those as mixed articles. Check both rules before the mould is cut. Retrofitting a stamp onto a finished batch is the most expensive way to learn this.

Flat diagram comparing a simple silver article with a mixed article containing steel and base metal parts
A silver part on a steel finding is not a simple silver article.

Packaging sits outside both rules, but it decides how the piece arrives. A silver chain in a paper box with no barrier film will take colour on a long sea route. The page on how a custom jewelry box is specified covers the box and the insert.

Small findings are their own trap. An earring back, a butterfly or a post often weighs little, and a supplier may substitute a base metal part without telling anyone. The page on how an earring line is sourced lists the parts to name in the spec.

925 SPEC SHEET

Send the drawing, the finished weight, the alloy name and the market you sell in. I will check the six lines above against what the factory quoted, flag the solder allowance, and tell you which test the shipment needs before it ships.

Send The Spec Sheet

Questions Buyers Ask About Sterling Silver

Is sterling silver the same as 925 silver?

Yes. Both names point to the same content rule, 925 parts silver per thousand. The word sterling carries the legal meaning, and 925 is the number behind it.

Is 999 silver better than 925?

It is purer and softer. Fine silver bends and scratches more easily, so most jewelry uses the alloy. Bars and coins use the pure metal because they are not worn.

Why does my sterling silver turn black in the box?

Sulfur compounds in the air react with the copper in the alloy. Warm, damp storage and paper packing make it faster. A sealed bag with an anti-tarnish strip slows it a lot.

Can a piece be marked 925 if it contains solder?

Yes, and the allowance grows. A part with solder may test 10 parts per thousand under the mark, while a part with no solder may only test 4 under it.

Is sterling silver hypoallergenic?

The word is not a standard. A reaction usually comes from nickel in a plating or a finding. Name the base metal and the finish in the spec, then test the finished piece.

Do small silver earrings need a UK hallmark?

An article under 7.78 grams of metal that holds silver of minimum fineness is exempt, unless it also holds another precious metal or a non-precious part. Check the exceptions before you print a claim.

Questions & Comments

We read every one and reply within 24 hours

Which mark is on the piece, and which market is it sold in? Send the stamp, the finished weight and the solder joins you were quoted, and I will check the three against the rule.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x