What Is White Gold? The Alloy, The Plate, The Marking
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is White Gold: Rhodium Is The Part That Wears Off

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao
· Updated November 16, 2026 · 9 min read

White gold is gold mixed with white metals, then covered with a thin layer of rhodium.

Two things are happening at once. The alloy decides the karat and the price. The plating decides the colour the customer sees on day one.

They wear at different speeds. Gold does not rub off a ring. Rhodium does, and when it goes, the metal underneath shows a pale yellow-grey.

This article covers what the word actually sells and what the US rules require you to disclose. It also covers where the plate wears first, and the six lines that keep a rework argument off your desk.

A white gold ring and a small rhodium plated band on a beige studio surface
Two rings, one word. The difference between them is a layer thinner than a sheet of paper.

The Short Answer

White gold is an alloy of gold. The karat tells you how much gold is in it, and that figure does not change because the alloy looks white.

Pure gold is soft and yellow. A jeweller adds other metals to harden it, and some of those metals are white. The result is a grey-white alloy that still reads as a metal, not as a bright white.

So the trade adds a plate. Rhodium, one of the platinum group metals, is electroplated on the finished piece. That plate is what makes the surface bright white and scratch resistant.

Three facts follow, and each one causes a dispute somewhere.

The karat is a gold content figure, not a colour figure. A 14K white ring and a 14K yellow ring hold the same amount of gold.

The plate is a surface, not a material. It is microns thin, so it wears at the points that touch things.

And a piece can be rhodium plated without being gold at all. Brass with a plate is sold as white gold in some catalogues, which is why the marking matters more than the photo.

The Word Names An Alloy

Karat is a simple fraction. Twenty-four karat is pure gold, so 18K is eighteen parts in twenty-four, and 14K is fourteen.

Put numbers on it. 18K is 75.0 percent gold, which is why the stamp reads 750. 14K is 58.3 percent, and the trade mark is 585.

Two cards showing 18K as 750 parts per thousand, 75.0 percent gold, and 14K as 585 parts per thousand, 58.3 percent gold
Karat is a gold figure. The white is the 25 or 41.7 percent that is not gold.

The other 41.7 percent of a 14K piece is where the colour comes from. Silver, copper, zinc, nickel and palladium all appear in white gold recipes, in ratios the alloy maker controls.

That is why two 14K white rings from two factories can look different before plating. One alloy is cool grey, another has a warmer cast.

It is also why “white gold” is a family name and not a spec. If the order does not name the karat and the alloy maker’s grade, the vendor is free to pick one.

There is a counter-intuitive point here that sales teams get wrong. The higher the gold share, the more whitening metal the alloy needs, because 18K starts closer to yellow than 14K does.

So an 18K white alloy is not simply a better 14K. It is a different balance of colour, hardness and cost, and it is worth telling a buyer that plainly.

Rhodium Is The Part That Wears Off

The plate is applied after the piece is polished, and it is measured in microns rather than millimetres.

Cross section of a white gold piece: a thin rhodium plate over a white gold alloy, with friction marked at the plate surface
The plate sits on top of the value. Friction reaches the plate long before it reaches the gold.

That is fine on a display tray and difficult in daily life. Ring edges, clasps and chain links rub against skin, cloth and other metal hundreds of times a day.

When the plate thins, the alloy shows through. On a ring the change looks like a faint warm patch at the edge of the band. It shows first where the finger meets the palm.

This is not a defect in the gold. The gold is intact and still 14K or 18K. What has gone is the finish, and a jeweller can put another one back.

The honest answer to “how long does it last” is that it depends on wear. A pair of earrings may hold a plate for years. A wedding band on a working hand may need attention far sooner.

Which is why a listing that says “white gold” and stops there tells a buyer almost nothing. It leaves out the karat, the alloy and the fact that a plate exists at all.

What The US Rules Require You To Say

The United States regulates the words, not the metal. The Federal Trade Commission publishes the jewelry guides in the FTC jewelry guides, and three sections matter for white gold.

The first is the karat mark. A gold alloy may not be described as “Gold” unless the karat fineness sits immediately before the word. That figure must be at least as large and as visible as the word.

The second is the plating. It is misleading to misrepresent the karat fineness, the thickness or the manner of application of a gold coating.

The third is the one most listings ignore. The guides say it is misleading to fail to disclose a surface layer of rhodium on a product marked or described as precious metal.

Read that again. The disclosure is not optional. A jeweller selling a rhodium plated white gold ring is supposed to say so.

The same part lists rhodium as a platinum group metal, next to platinum, palladium, iridium, ruthenium and osmium. It allows the abbreviation “Rhod.” or “Rh.” in a quality mark.

What the listing saysWhat it should supportWhat to ask for
18K white gold750 parts gold, white alloy, rhodium plate statedThe stamp and the plating disclosure
14K white gold585 parts gold, white alloy, rhodium plate statedSame, plus the alloy maker’s grade
White gold platedA base metal with a gold layer, not a solid alloyThe base metal, and the plating thickness
Rhodium plated brassNo gold content at allWhether it is legal to call it white gold in your market

Three Things Get Sold Under One Name

The trade uses the same words for three different products, and the price gap is large.

Solid white gold. A gold alloy throughout, stamped with its karat, then plated with rhodium. This is the product the name was built for.

Nickel-white and palladium-white alloys. Both are white gold, and they differ in the metal that does the whitening. Palladium alloys cost more and are the usual answer when a buyer asks for a nickel-free option.

Plated base metal. Brass or another alloy, plated with rhodium or a white gold layer. It can look convincing in a photo, and it is a different product in law and in wear.

A fourth case sits between them: gold filled or heavy plated stock. It carries real gold on the outside and a base metal inside, and it usually has its own label rules.

ProductGold contentWhat wearsPrice driver
Solid white gold, 18K750 parts, 75 %The rhodium plateGold per gram
Solid white gold, 14K585 parts, 58.3 %The rhodium plateGold per gram
Palladium white alloySame karat, white metalThe plate, more slowlyAlloy cost
Plated base metalNoneThe plate, then the baseLabour per piece

The check is cheap. Look for the karat stamp inside the band, and weigh the piece against a known solid one. Then read the price per gram of gold in the quote.

A quote that gives a per-gram gold price is a quote from someone selling gold. A quote that gives only a unit price is a quote from someone selling a finish.

Replating: What Actually Happens

A jeweller does not paint on a new colour. The old plate is removed, the metal is polished, and a fresh layer goes on.

Stones usually get masked or taken out first, because plating solution should not reach a setting. That step, not the rhodium, is where the labour sits.

Then the piece is cleaned, plated, rinsed and dried. A simple band is quick work. A pavé setting is slow work and carries more risk.

Three things drive the final price. The labour for masking and polishing, the rhodium itself, and the risk that a setting does not survive the strip and polish.

There is also a specification choice. A thicker plate lasts longer and costs more per piece, and it is the number most factories never quote.

For a brand, the useful question is not “how much is replating”. It is who pays for the second plate, and how long the first one is promised to last.

What Wears First, And How To Slow It

Wear is predictable once you know where it happens.

The inner edge of a ring takes the most friction, because it touches skin all day. Clasp tongues and the links next to them go next. On earrings, it is the post and the hinge.

Household chemicals accelerate the change. Chlorine is the one to keep away, and repeated hand sanitiser use is the other common cause of dullness.

Storage matters less than people think, but abrasion between pieces does thin a plate. A velvet-lined box beats a bowl of loose jewellery.

None of this is a reason to avoid the product. It is a reason to state the finish in the listing, so a customer knows what will happen in year two.

How To Check A Piece In Ten Minutes

You do not need a laboratory to catch the obvious substitutions, and the obvious ones are the expensive ones.

Read the stamp. A solid gold piece carries a karat mark, usually inside the band or on the clasp. 585 and 750 are the figures that matter, and they should be crisp rather than scratched in by hand.

Look at a worn edge with a loupe. Where the plate has thinned, you will see a colour change from white to warm. That tells you the piece was plated, which the listing should have said.

Weigh it against a known piece. Gold alloys are dense, and a plated brass copy of the same size usually feels light in the hand. Density is a better guide than sound.

Skip the magnet test. It is popular online advice and it proves almost nothing, because brass and gold are both non-magnetic.

Use an acid kit with care, or ask for an X-ray fluorescence reading. Acid leaves a mark, so test inside the band rather than on the face.

None of these replaces an assay when the value is high. They do tell you, before you pay for one, whether the seller is describing the same product you are holding.

Buying From A Factory: Six Questions

A factory in China will quote white gold in a day. These six questions take a week and tell you whether the quote is real.

One. What karat, and what will the stamp read: 585, 750, or a karat mark with the metal name?

Two. Which alloy does the maker use, and is a nickel-free version available at what price difference?

Three. Is the rhodium plate quoted in microns, and what thickness is standard for this product?

Four. What is the disclosed finish on the listing: rhodium plated, or unplated white alloy?

Five. On a repair, does the factory replate, or does the brand find a local jeweller?

Six. Which lab can check the karat, and does the factory pay for the assay on the first order?

A supplier who answers all six is quoting a material. A supplier who answers three is quoting a photograph.

Six Lines For The Order Sheet

These six lines fit on one page and settle the argument before the first sample is polished.

One, the karat and the stamp. 585 or 750, and the words that will sit next to the mark on the finished piece.

Two, the alloy. Which white alloy, from which maker, and whether a nickel-free version is required.

Three, the plate. Rhodium, with a thickness in microns and a stated minimum.

Four, the disclosure. The listing and the invoice both say rhodium plated, in the market’s own words.

Five, the assay. Who tests the karat, on which pieces, and what happens if a piece fails.

Six, the second plate. Who pays for replating, and what the brand promises the customer about the finish.

Put all six into the build sheet a workshop signs off before the sample is made. The plating route itself is worth a separate read: how PVD compares with electroplating decides what the surface looks like after a year.

If the line is new to you, start with the sourcing route for a jewelry line and bring the six lines to the first meeting.

When the goods are ready, an inspection before the goods leave should check the stamp on a sample of pieces. Counting cartons is not enough.

Six numbered clauses for specifying white gold on an order sheet, from karat and stamp to the second plate
Six clauses. The first three decide the metal; the last three decide who pays when the plate goes.
READ THE STAMP

Send the listing and the factory quote. I will check the karat mark, the alloy and the plating disclosure against the market you sell in. Then I will tell you which of the six lines is missing, and what to ask for instead.

Ask For A Marking Check
Is white gold real gold?

Yes, if the karat says so. A 14K white gold piece is 58.3 percent gold by definition, and the trade stamps it 585. The colour comes from the other metals, not from a substitute.

Why does my white gold ring look yellow at the edges?

The rhodium plate has worn through and the alloy underneath is showing. The gold is still there. A jeweller can strip, polish and replate the piece.

Is white gold hypoallergenic?

Not automatically. Nickel is used in some white alloys, and it is the usual reason a wearer reacts. Ask the factory for a palladium-based alloy if that matters to your customer.

Does rhodium plating add value?

No. Value comes from the gold content and the make. Rhodium is a finish, and a thin one costs very little per piece.

Can silver be rhodium plated and sold as white gold?

It can be plated, but it is silver, not gold. Selling it as white gold would misstate the metal content, which the US jewelry guides treat as misleading.

How often should a ring be replated?

When the edge starts to look warm rather than white. That is wear, not a date on a calendar, so a daily-worn band will need it well before an occasional piece.

Questions & Comments

We read every one and reply within 24 hours

If a white gold listing lands on your desk, send it over. I will read the karat mark, the alloy and the plating disclosure against the market you sell into.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x