What Is Tritan Material: A Trademark, Not A Plastic Family
Tritan is a clear, tough copolyester from Eastman, and the name is a trademark.
That single fact changes how a quotation should be read. A factory can print the word on a sheet without buying a kilogram of the resin.
Two other words do most of the confusing. “Copolyester” describes the chemistry. “BPA-free” describes an ingredient list, not a finished part.
This article separates the three and gives the resin numbers worth copying into a specification. It ends with seven lines for an order sheet.
The Material Behind The Name
A copolyester is a polyester built from more than one acid and more than one alcohol. The mix is what makes a resin clear and tough at the same time.
Three building blocks are named in the published work on this material. Dimethyl terephthalate brings stiffness to the chain, and 1,4-cyclohexanedimethanol keeps the chains from packing into crystals.
The third is 2,2,4,4-tetramethyl-1,3-cyclobutanediol. That bulky ring is the reason a thin wall keeps its shape when the contents are warm.
The paper summary that lists those three monomers also reports what came out of finished bottles, and that part matters later.
None of the three is bisphenol A. Eastman says on its own site that BPA “is not and has never been an ingredient or byproduct of the production of Tritan”.
Most writing about the resin is still about safety. The moulding questions get skipped, and that is where a buyer loses money.
In the moulding shop it behaves like an engineering plastic. It is amorphous, so it has no sharp melting point and it shrinks less than a semi-crystalline resin such as polypropylene.
Light crosses it easily. A test plaque measures 90 to 92 percent total transmittance with haze under one percent, on Eastman’s own data sheets.
It is not unbreakable. The maker’s phrase is shatter resistant. The honest check is an impact test at a stated temperature, not a squeeze in the hand.
One more boundary. Tritan is a brand with many grades, in the way that stainless steel is a family with many grades. The name alone does not tell a moulder what to set on the machine.
The Numbers To Copy Into A Spec
Adjectives do not survive a price meeting. Numbers do. The table below comes from two Eastman data sheets, for the injection grade TX1001 and for TX2001.
| Property | TX1001 | TX2001 | Method |
|---|---|---|---|
| Specific gravity | 1.18 | 1.17 | D792, g/cm³ |
| Mould shrinkage | 0.5 to 0.7 | 0.5 to 0.7 | D955, percent |
| Tensile stress at yield | 43 | 45 | ISO 527, MPa |
| Elongation at break | 210 | 140 | D638, percent |
| Notched Izod, 23 °C | 980 | 650 | D256, J/m |
| Notched Izod, −40 °C | 20 | 14 | ISO 180, kJ/m² |
| Heat deflection at 0.455 MPa | 99 | 109 | D648, °C |
| Heat deflection at 1.82 MPa | 85 | 92 | D648, °C |
| Total transmittance | 90 | 92 | D1003, percent |
| Haze | below 1 | below 1 | D1003, percent |
| Drying | 88 °C, 4 to 6 h | 88 °C, 4 to 6 h | before moulding |
| Melt temperature | 260 to 282 | 260 to 282 | °C |
| Mould temperature | 38 to 66 | 38 to 66 | °C |
| Agency listings | NSF/ANSI 51 and 61 | NSF/ANSI 51 | food, water |
Five rows settle most arguments. Density sets the weight of the part and so the resin bill. Heat deflection at your real load decides whether a hot fill is safe.
Impact at the lowest temperature your market sees decides whether a winter drop test passes. Shrinkage sets the tool size. Drying decides whether the part comes out clear or milky.
Read the heat rows as a pair. The same resin gives two answers, fourteen degrees apart, and the only difference is the load on the test bar.
Heat deflection is not a maximum use temperature either. It is the point where a loaded bar bends a set distance in a lab. A dishwasher and a hot car are not that test.
Note the word typical on those sheets. Eastman’s own note says a shipment need not match the table, and colour, wall design and drying can move the result. Treat the numbers as a target, not a promise.
Tritan, Polycarbonate And Polypropylene
Most sourcing decisions are not Tritan against nothing. They are Tritan against the clear resin the factory already runs, or against the cheap one.
Polycarbonate is the resin Tritan was sold against. It is clear and it takes heat, and BPA is a building block of it. That is why the European rules now treat it as a separate problem.
Polypropylene is the cheap one. Polypropylene runs fast and welds well. It is also the lightest of the three: 0.895 to 0.93 grams per cubic centimetre, against 1.17 for TX2001.
That density gap is money. A part of the same outer shape weighs about a fifth less in PP. The resin line falls before the price per kilogram is even compared.
The catch is what a shopper sees. Polypropylene is translucent at most, and it goes chalky with scratching. A clear bottle or a clear jug is not a PP job.
| Question | Tritan | Polycarbonate | Polypropylene |
|---|---|---|---|
| Water clear on a thick wall | Yes | Yes | Rarely |
| Bisphenol A in the recipe | No | Yes | No |
| Cost direction per part | Highest of the three | Middle | Lowest |
| Weight of the same shape | Baseline | Close to baseline | About a fifth lighter |
| Cold impact | High | High, with a notch risk | Poor below zero |
| Scratch and haze over time | Slow | Slow | Fast |
| Typical job | Reusable bottle, jug, lid | Older clear ware, jugs | Lids, tubs, closures |
The table is a start, not a decision. A drinkware programme often pairs a clear body with a PP lid and a silicone seal. One product then carries three materials and three sets of rules.
How a drinkware line is built is the wider picture. The lid and the print are the parts that fail first.
What BPA-Free Can And Cannot Mean
The phrase describes a recipe, not a measurement. Eastman states that BPA has never been an ingredient or a byproduct of this resin. It also states the material is free of BPS and other bisphenols.
That claim used to be a marketing line. Since December 2024 it has been a purchasing deadline in Europe, which changes who has to care.
Regulation (EU) 2024/3190 bans bisphenol A in materials that touch food. It was adopted on 19 December 2024 and published on 31 December 2024. It repeals the older migration limit that allowed small amounts.
The dates are the useful part. Single-use articles that do not meet the new rules may still be placed on the market until 20 July 2026.
Repeat-use articles that do not meet the rules may be first placed on the market until 20 July 2026. For professional food production equipment the date moves to 20 January 2028.
Ware already placed under those transitional rules may stay on sale until 20 January 2029. A buyer planning a 2027 range should read that line twice.
The ban also covers other bisphenols with a hazard classification, and bisphenol S is named in the text. A supplier who swaps BPA for BPS has not solved the problem, and the regulation says so in plain words.
None of this bites on the Tritan body, because the recipe has no bisphenol in it. It bites on everything else in the same product.
A bottle has a body, a lid, a gasket, sometimes a straw, and often a print or a label. Each of those is a separate food contact surface with its own material and its own paperwork.
That is where a “BPA-free” badge on the carton does the buyer no good. The rules for kitchenware that touches food apply to the finished article, not to the pellet.
The second half of the story is measurement. A study of reusable bottles sold in Europe found BPA in the first migration test. The level was about 0.030 micrograms per kilogram, and later tests showed none above the detection limit.
The same study found benzylbutyl phthalate at about 0.040 micrograms per kilogram in all three tests. A large water container also released one non-intentionally added substance. Every figure sat below the legal limit in force at the time.
A yeast test on the same extracts found no hormone-like activity. That test is less sensitive than the cell test used by other researchers. Both readings are in the source, and both belong in the file.
So write the claim in the form the evidence supports. “The body resin is made without bisphenols” is a statement about the recipe, and it is solid.
“No bisphenol was detected in the finished article” is a claim about a test. It needs a report number, a method and a detection limit. Without those three it is an opinion with a logo.
How To Check A Claim In A Quote
Five questions split a real material from a label. None of them needs a laboratory visit, and all of them fit in one email.
One: the grade. Tritan is a family, not a single resin. TX1001 is the general injection grade, TX1501HF flows faster, TX2001 takes more heat, and the Renew versions carry recycled content.
Ask for the grade name and the maker on the specification. You would ask for 304 or 316 in a steel part, and this is the same question. A sheet that says only “Tritan” has told you nothing yet.
Two: the lot. A certificate of analysis carries a lot number, a date and measured values. If the factory cannot produce one for the run it is quoting, the resin came from somewhere else.
Three: the plant. Eastman makes Tritan Renew in Kingsport, Tennessee. The origin is checkable, and a claim about recycled content should carry the certification behind it.
Four: the permission. Tritan is a trademark, and the brand owner usually holds the right to print it on a product. Ask who authorised the mark on the carton, then ask for it in writing.
Five: the look-alike. A clear copolyester can be swapped for another clear copolyester without changing the drawing. Density and an infrared scan against a known sample will separate them.
Send the lab a sample of the part and a sample you trust, and ask for a comparison. A test that tries to name the polymer from nothing invites an argument you will lose.
The recycling number is not a check. Resin code 7 is the catch-all for everything outside codes 1 to 6. It covers polycarbonate and nylon as readily as Tritan.
What The Mould Has To Do
The resin is less forgiving than it looks, and most of the trouble is water. Pellets absorb moisture in the bag, and moisture turns into haze and silver streaks on the wall.
Dry at 88 °C for four to six hours, and check the dryer, not the clock. A dryer working at half capacity will pass a timer test and fail at the gate.
The melt window runs from 260 to 282 °C. Too cold and the flow front freezes early, which leaves weld lines and a blush at the gate. Too hot and the chain breaks down, which shows as yellowing.
Eastman’s own data sheet warns about that breakdown by name, and asks the moulder to watch residence time and shot size. Long dwell at high heat costs clarity, and clarity is the product.
Mould temperature runs from 38 to 66 °C. A warm tool fills better and hides weld lines, at the cost of cycle time. A cold tool is faster and freezes stress into the part.
The resin is amorphous and shrinks 0.5 to 0.7 percent, which is low and fairly even in both directions. That is why a clear Tritan part can hold a straight wall where a polypropylene part would bow.
The catch is that low shrinkage does not mean no stress. Thick sections, sharp corners and a gate in the wrong place all leave frozen stress. A stressed part is the one that cracks in a dishwasher.
Gate placement is a commercial decision, not only an engineering one. On a clear part the gate mark is visible. Put it on the base or under the lid, and write the allowed size into the drawing.
Tool polish carries straight through to the product. A cavity finished to a coarse grade gives a hazy wall. No amount of resin can fix it, and buyers read that haze as cheap material.
Then there is the mixed-resin problem. A Tritan body with a polypropylene lid has two shrinkages and two heat expansions. The thread and the seal have to absorb both.
What a tool costs in China is the other half of that conversation. The tolerance you ask for is the part of the price you can still control.
Heat, Dishwashers And Boiling Water
The heat question arrives in three forms, and they are not the same question. One is a lab bar under load, one is a dishwasher cycle, one is a kettle.
The lab bar gives 99 °C for TX1001 at a light load and 85 °C at a heavy one. TX2001 gives 109 °C and 92 °C. Neither figure is a working temperature for a bottle.
The dishwasher is closer to real life, and it is where the resin was designed to work. Eastman’s own test material describes a ten-day soak at 70 °C in a dishwasher detergent solution.
Hot water alone is not the hard part. Detergent attacks the surface, and a stressed part fails at the point where the two meet. That is why the base and the thread crack first.
Boiling water is the third question, and the maker answers it in a narrow way. Eastman states that Tritan Renew is cleared by the FDA for food contact at temperatures up to and including 100 °C.
That is a clearance for the resin, and it is also a claim about a test. It does not cover your lid, your gasket, your print, or the pressure that builds in a sealed bottle.
A sealed bottle filled with boiling liquid holds steam under pressure. Leave head space, vent the cap, and put the warning on the label if the product is sold for hot drinks.
Cleaning a bottle without dulling it is the consumer side of the same chemistry. The advice there is mostly about detergent and heat.
What To Inspect At Goods-In
A clear part shows every fault, which is good news. The checks below need a lamp, a gauge and a scale, not a laboratory.
Haze. Agree a limit on a stated wall thickness and measure it against a sample you signed. Without a signed sample, the argument is about adjectives.
Gate and weld line. Look at the base and the thread under a bright lamp at an angle. A white blush or a visible line on a drinking surface is a reject, not a cosmetic.
Stress. A polarised light viewer shows frozen stress as coloured bands. It costs little and it finds the parts that will crack in a dishwasher three months later.
Drop test. Fill the bottle, chill it to a stated temperature, and drop it from a stated height onto a stated floor. Write all four conditions, or the result cannot be repeated.
Cycle test. Run a fixed number of dishwasher cycles with detergent, then re-check haze, crazing and colour. A part can look flawless on day one and go milky in a month.
Neck and thread. Measure with a gauge, then fill and shake. Leaks start at the thread far more often than at the wall, and the wall is what everyone photographs.
Weight spread. Weigh ten parts from one carton. A wide spread means unstable moulding, and unstable processing means the next carton may look different.
Paperwork. The food contact report has to cover the finished article and the market you sell into. A resin certificate on its own leaves the lid and the print uncovered.
An independent check before shipment closes the loop. The sample you approved and the carton you receive are often made a month apart.
An inspection staged before the container leaves is cheaper than a recall, and the list above is its checklist.
Seven Lines For The Order Sheet
Each line closes a gap that the word Tritan leaves open. Together they fit on one page and they settle most disputes before they start.
One. The resin: maker, grade and colour code, written by name. “Tritan or equivalent” is not a line, it is an invitation.
Two. The bisphenol statement: no bisphenol in the recipe of the body, and the same statement for the lid and the seal.
Three. The food contact report: which market, which test conditions, and which parts of the product it covers.
Four. The processing record: drying temperature and time, melt range, mould range, and the shot weight for the approved sample.
Five. The optical limit: haze value, the wall thickness it was measured on, and the allowed gate mark.
Six. The durability test: dishwasher cycles with detergent and temperature, plus the drop height, temperature and floor.
Seven. The mark: who authorised the Tritan name on the product and the carton, and where that approval is filed.
Seven lines is a short document. The document a moulder works from only holds if the factory signs the same page you approved.
Send me the quote for a Tritan bottle, jug or lid. Add the resin certificate if the factory has one. I will check the grade name, whether the bisphenol statement covers the lid and the seal, and where the tool’s shrinkage allowance came from. No cost, no obligation.
Check My QuoteQuestions Buyers Ask
Is Tritan a type of plastic?
Yes, it is a copolyester plastic. The name is a trademark owned by Eastman. It points to a brand and a set of grades, not one chemical recipe.
Is Tritan really BPA-free?
The maker states that BPA has never been an ingredient or a byproduct of the resin. It also states the resin is free of BPS and other bisphenols. That is a claim about the recipe. A claim about the finished part needs a test report.
Can I put boiling water in a Tritan bottle?
The resin is cleared for food contact up to 100 °C. A sealed bottle of boiling liquid is under pressure as soon as the cap goes on. The lid and seal sit outside that clearance, so design and labelling decide.
Is Tritan dishwasher safe?
The resin is built for it, and the maker describes ten days at 70 °C in detergent solution. Lids, seals and printed decoration may not share that rating, so check them separately.
Is Tritan better than polycarbonate?
It is clearer on thick walls, and it has no bisphenol in the recipe. That matters more now that Europe restricts BPA in food contact articles. Polycarbonate remains stiffer and cheaper.
How can I tell Tritan from another clear plastic?
Not by eye. Density and an infrared scan against a sample you trust will split the look-alikes. The recycling number 7 tells you nothing either way.
Questions & Comments
We read every one and reply within 24 hoursIf a Tritan quote lands on your desk, send it over. I will read the grade name, the bisphenol statement and the tool allowance, and tell you which of the three is missing.