Titanium Jewelry: Grade 2 vs Grade 5
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Titanium Jewelry, And Which Grade Are You Buying?

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao
· Updated November 16, 2026 · 12 min read

Titanium jewelry is jewelry made from titanium metal, and in practice that means one of five grades. It is a base metal, not a precious one, so the words on the tag follow a different set of rules from gold or platinum.

That single fact decides most of what a buyer has to get right. The grade sets the weight, the finish, the tool wear and the price. The rules set what may be printed next to it.

This page covers both halves, then hands you the seven lines for an order.

Brushed titanium ring resting on a warm beige studio surface beside a matte grey titanium chain, with soft directional light
The grey is the metal. There is no plating in the colour.

The Short Answer

Titanium is a light, hard, corrosion resistant metal. It sits at number 22 on the periodic table, and it takes an oxide layer on its surface within seconds of meeting air.

That oxide layer is the useful part. It seals the metal, so it does not rust, and it can be grown on purpose to make colour.

The metal comes in grades, and the grades are not marketing tiers. They are different specifications with different chemistry.

Four of them are called commercially pure. They are titanium with small amounts of oxygen and iron, and nothing else added on purpose.

The fifth, grade 5, is an alloy with six percent aluminium and four percent vanadium. It is much stronger, and it is harder to work.

Most titanium jewelry sold today is grade 2 or grade 5. Rings and bracelets are usually grade 2 for the polish, and heavy-duty bands are often grade 5.

Neither one is a precious metal. Both are sold by weight of bar stock, not by karat, and neither carries a hallmark.

One Metal, Five Grades

The commercially pure grades are separated by oxygen content, not by alloying. More oxygen makes the metal harder and less ductile.

Grade 1 is the softest and most ductile, and it is used for cold forming. Grade 2 is the standard workshop grade. Grades 3 and 4 step up in oxygen and strength.

Grade 5 is the alloy. The published composition is six percent aluminium, four percent vanadium, no more than 0.25 percent iron and no more than 0.2 percent oxygen.

There is a sixth grade worth knowing about, grade 23. It is the same alloy with less oxygen, and it is the one the implant standards name.

GradeWhat it isHow it behaves at the benchWhy a jewelry line picks it
Grade 1Commercially pure, lowest oxygenSoftest, most ductile, forms coldDeep drawn or bent shapes
Grade 2Commercially pure, standard oxygenMachines and polishes wellThe default for rings, bands and chains
Grade 3 and 4Commercially pure, higher oxygenHarder, less forgiving, still weldableThinner sections that must hold shape
Grade 5Ti-6Al-4V alloyStrong, springy, heavy tool wearThin wide bands and clasps
Grade 23Ti-6Al-4V ELI, lower oxygenSame alloy, more ductile and tougherItems that touch a piercing

The grade choice is a cost decision as much as a technical one. Grade 5 cuts slower, because its thermal conductivity is about sixty percent lower than the pure grades.

Heat stays at the cutting edge instead of leaving through the chip. Tools wear faster, and the cycle time per piece goes up.

So a band quoted in grade 5 is not a grade 2 band with a better word on it. It is a different bar, a different program and a different price.

Ask which grade, and ask for the bar certificate with the heat number on it. The two answers should match, and they often do not.

Flat vector panel on a cream background comparing titanium grade 2, grade 5 and grade 23 across strength, ductility and machining cost, with simple bar indicators
Strength up, workability down. The trade runs in one direction.

What 4.5 Grams Per Cubic Centimetre Buys You

Titanium's density is 4.502 grams per cubic centimetre at room temperature. Fine gold is 19.283.

Put the two numbers side by side and the selling point becomes arithmetic. The same volume of gold weighs about four and a quarter times as much.

Take a plain band eight millimetres wide and two millimetres thick, with a twenty millimetre bore. The metal volume is about one cubic centimetre.

In titanium that band weighs around 4.5 grams. In fine gold the same shape weighs around 19.3 grams.

Fourteen grams of difference is the whole pitch. It is why a wide men’s band in titanium feels like a narrow one in gold.

Hardness runs the other way. Titanium sits at 6.0 on the Mohs scale, and fine gold sits at 2.5.

Stiffness is measured by the modulus. Titanium is 120 gigapascals and gold is 79, so a titanium band resists bending with less metal behind it.

Heat is the part buyers notice and rarely name. Titanium conducts heat at 21.9 watts per metre kelvin, against 318 for gold.

That is why a titanium ring feels warm to the touch in a cold room. It also takes longer to feel cold on the finger. The metal is not changing temperature faster; it is moving heat away slower.

The colour also comes from the metal. Titanium is grey, and it stays grey, because there is no plating to wear through.

Flat vector panel comparing the mass of one titanium band and the same band in fine gold, with the weight ratio and the hardness and heat figures alongside
Same drawing, same volume. The scale is the difference.

Nickel Is The Only Skin Claim With A Number

Most metal allergy talk is vague. In Europe there is a figure, and it applies to jewelry by name.

The EU restriction on nickel sets a release rate, not a content limit. For parts that go into a pierced ear or another piercing, the rate must stay below 0.2 micrograms per square centimetre per week.

For articles in direct and prolonged contact with the skin, the rate must not exceed 0.5. The list includes earrings, necklaces, bracelets, chains, rings and watch cases and straps.

A coating counts too. Where a non-nickel coating is used, it has to keep the rate under 0.5 for at least two years of normal use.

The regulation names the European standards as the test methods, and it bars the articles from the market unless they meet the rate. That is a hard gate, not a marketing preference.

Titanium helps here, because the metal carries no nickel. Neither does grade 5, whose alloying elements are aluminium and vanadium.

But the metal is rarely the whole product. A stud has a post and a clutch. A pendant hangs on a chain with a spring ring. Those parts are often bought in and can be stainless steel.

So the question is not only what the band is made from. It is what else touches the skin, and what the coating is.

Gold plated titanium is a case in point. A thin gold layer over a nickel underlayer puts the nickel back. The two year rule then decides whether the piece can be sold in Europe at all.

This is also where posts and clasps bought as a separate part matter: the metal you chose is only one input to the release rate.

What The Listing May Say

The words around the product are governed by the US jewelry guides, and four sections do most of the work.

Start with the word precious. A section of the guides bars “real”, “genuine”, “natural” and “precious” on a product that is manufactured or produced artificially.

Titanium is a base metal. Calling it precious is not a loose description; it is the conduct that section describes.

Next, corrosion. The guides allow “corrosion proof” only where every part of the product is immune from rust and corrosion for its whole life expectancy.

“Corrosion resistant” has a lower bar, but still a bar. Every part has to resist material damage through the major part of that life under normal use.

The guides even list metals they are willing to treat as resistant: pure nickel, gold alloys of ten karat or more, and austenitic stainless steels.

Titanium is not on that list. It may well qualify on the evidence, but the claim needs the evidence, and the plating and the findings have to qualify with it.

Third, plating. Misstating the presence of gold, the karat, the thickness, the weight ratio or the way it was applied is deceptive.

So “gold plated” without a thickness or a ratio is thin ground. The guides name exactly those details as the ones that must not be misstated.

Fourth, the general rule behind all of them. A description is deceptive if it misleads a reasonable buyer, whatever the individual section says.

Words on the listingWhat the rule requiresThe safe version
Precious titaniumBars “precious” on an artificial productTitanium, or titanium alloy
Corrosion proofEvery part immune for the product’s whole lifeCorrosion resistant, with the parts named
Gold plated titaniumState the karat, the thickness and the weight ratio exactlyState the karat and the plating thickness
Implant gradeNot defined in the guides; needs a standard behind itName the standard and attach the certificate
Aircraft gradeNot a grade in any titanium standardName the grade, such as grade 5

Two of those rows are worth dwelling on, because they are the ones suppliers reach for most.

Implant grade is a real claim when it is tied to a standard. The ELI alloy is covered by ASTM F136, and unalloyed titanium by ASTM F67.

Without the standard on the certificate, the phrase is an adjective. A buyer cannot check an adjective.

Aircraft grade is worse, because it is not a grade name at all. Grade 5 is used in airframes, and that is where the phrase came from, but no titanium standard defines it.

If the supplier means grade 5, the sheet should say grade 5, with the bar certificate to match.

Marking is the other half of the claim. Titanium takes a laser mark without ink, so the grade and the size can be marked on the inside of a band and stay readable.

The choice between laser marking and printed decoration also decides whether the mark survives polishing, which is a usual place for a claim to disappear.

Why Titanium Is Machined, Not Soldered

Silver and gold are forgiving at the bench. They anneal with a torch, solder with a lower melting alloy, and can be sized after the fact.

Titanium is not forgiving in the same way. When it is hot it takes oxygen into the metal, and that turns the surface brittle.

So joining is not a torch and a stick of solder. It is welding with the joint shielded from air, which is a different workshop and a different cost.

Sizing is the practical casualty. A titanium band cannot be stretched or cut and rejoined like a gold one, so it is sold as a fixed size.

Two ways around that exist. A comfort fit inside profile makes a half size less critical. The other route is a full size run, with the stock held by the buyer.

Ask which one is on offer before the order, because the answer changes the size curve and the returns policy.

Forming is the other half. Grade 1 forms cold, which is why it is the grade for bent and drawn shapes. Grade 2 machines well and takes a bright polish.

Grade 5 is stronger and springier. It holds a thin section where grade 2 would bend, and it costs more to cut for the reason in the first section.

None of that is mysterious to a factory that already runs the metal. It is worth checking early how a jewelry line is set up with a factory. A workshop that casts silver all day may not have a lathe set up for titanium at all.

What A Bench Can Prove

Three questions get mixed into one at a trade show: is it titanium, which grade, and is the coating what they said.

Two of the three are quick. The middle one splits in a way that catches people out.

Grade family is easy. A hand held X-ray gun reads the alloying elements, so six percent aluminium and four percent vanadium show up at once.

A reading with both elements present is grade 5 or grade 23. A reading with neither is one of the pure grades. That takes a minute and costs almost nothing.

Which pure grade is the hard one. Grades 1, 2 and 4 are all titanium with oxygen as the difference, and an X-ray gun does not read oxygen.

That needs a laboratory method for gas content, which means a sample and a wait. So a supplier who claims grade 2 has made a claim most buyers never test.

Coating is measurable on the surface. A plating thickness gauge reads a gold layer, and a coating that is missing will not read at all.

Nickel release is measured by the European standards the regulation names. It is a wet test, not a scan, and it is the only one that speaks to the skin claim.

The bar certificate is the other half of the file. It carries a heat number that ties the bar to the mill, and that number should appear on the invoice for the finished goods.

QuestionWhat settles itWhat it costs in time
Alloy or pure gradeA hand held X-ray scanMinutes, no sample
Which pure gradeAn oxygen test in a laboratoryDays, and a sample
Coating thicknessA plating gauge, or a cross sectionMinutes on a flat face
Nickel releaseThe standard wet testDays, and a cut sample
Bar originThe bar certificate and its heat numberSame day, from the mill
Flat vector panel with two columns headed easy to check and needs a laboratory, listing grade family, coating thickness and nickel release against oxygen content and bar origin
One scan, one wet test, one certificate. The rest is paperwork.

Titanium has one more wrinkle worth knowing. It is not magnetic, and it is a poor conductor, so the tricks people use on other metals do not apply.

A magnet tells you nothing, because stainless steel findings are also often non-magnetic. The scan and the certificate are the checks that work.

Seven Lines For The Order Sheet

Each line below closes one argument. Written together they take ten minutes, and they decide what can still be argued about when the goods land.

1. Grade and certificate. Name the grade, and require the bar certificate with the heat number on it.

2. Weight per piece. Give a target in grams. Density is known, so weight is a cheap check on wall thickness and on the grade.

3. Finish and coating. State polished, brushed or blasted, and if there is a coating, its type and thickness in microns.

4. Findings and the nickel statement. Name the post and clutch material, and require a release figure or a certificate that covers them.

5. Marking. Name the method, the grade text and where it sits, so the mark is not lost at the polishing wheel.

6. Size range and the sizing policy. Fix the run and state that the band cannot be resized, so the size chart and the returns rule match.

7. Acceptance tests. Name the scan, the wet test and the sample size. Put the pass and fail numbers on the sheet, not in an email.

Four lines are checks and three are choices. That ratio is normal for a metal order, and it is why the sheet outranks the sample.

The pattern carries over from other products. It is the same shape as the specification sheet a factory signs, with the metal columns swapped in.

GRADE CHECK

Send me a titanium quotation, a bar certificate or a listing you are about to publish. I will check the grade against the certificate, the coating against the claim, and the wording against the jewelry guides. Then I will tell you which line is still open before the order goes out. No cost, no obligation.

Send The Spec

Questions Buyers Ask

Is titanium jewelry worth the price?

It is cheap as a metal and costly to machine. You pay for the light weight, the grey colour that cannot wear off, and the absence of nickel in the metal itself.

Is grade 5 better than grade 2?

It is stronger and springier, and it costs more to cut. For a thick plain band grade 2 is usually enough. For a thin wide band, grade 5 holds the shape.

Is titanium jewelry hypoallergenic?

The metal carries no nickel, which is the usual cause of a reaction. The coating and the findings can still bring nickel into the product, so the release rate is the number to ask for.

Why can titanium rings not be resized?

Because the metal cannot be soldered with a torch and rejoined like gold or silver. Sizing is a welding job in a shielded atmosphere, so most lines sell a fixed size run instead.

Does titanium jewelry tarnish?

No, and the reason is the oxide layer that forms on the surface within seconds. It seals the metal, so the grey stays grey. Coatings can still wear, and a plated piece is a different story.

Can a shop test the grade while I wait?

A scan separates the alloy from the pure grades in about a minute. Telling grade 1 from grade 2 needs an oxygen test in a laboratory, which means a sample and a few days.

Questions & Comments

We read every one and reply within 24 hours

If a titanium quotation or a bar certificate lands on your desk, send it over. I will read the grade against the certificate, the coating against the claim, and the wording against the jewelry guides.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x