Moissanite vs Diamond: The Numbers Buyers Check
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Moissanite vs Diamond: What a Buyer Checks Before the First Order

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 16, 2026 · 13 min read

Moissanite is silicon carbide. Diamond is carbon.

That single line settles most of the argument. The two stones look alike from a metre away, and they are not the same material at any distance.

One is a mineral of pure carbon, crystallised under pressure a hundred miles down. The other is silicon carbide, grown in a furnace and cut like a gem.

Both can sit in the same ring setting. Both can pass a quick look. Only one can legally be called a diamond in the United States.

Most pages that compare the two run on adjectives. More fire, more brilliance, better value. This one runs on what a buyer can check. The federal definition, the physical numbers, and the three field tests that catch a mixed parcel.

Studio still life of loose colourless stones beside a simple ring on a beige surface
At arm’s length they read the same. The invoice has to say which one it is.

The Short Answer

Moissanite and diamond are different minerals. That is the answer, and everything else follows from it.

Diamond is carbon in the isometric system. Moissanite is silicon carbide, written SiC. Different atoms, different crystal, different behaviour.

Hardness is close and not equal. Diamond sits at the upper end of the Mohs scale at 10. Moissanite is usually listed just under it.

Optics split more sharply. Diamond has one refractive index. Moissanite has two, because its crystal is birefringent.

Price differs for a structural reason. Diamond supply comes out of mines and labs under tight grading. Moissanite is grown in furnaces in large crystal boules.

So the useful question is not which stone wins. It is which claim your product line can support, in the market where you sell it.

A fashion line can sell moissanite honestly and profitably. A bridal line that needs a grading report needs a stone the labs report on.

Both are legitimate businesses. The failures happen when the paperwork says one thing and the stone says another.

The Word On The Invoice Is Regulated

In the United States, the word diamond has a legal rule with numbers inside it. It sits in the FTC Jewelry Guides, at 16 CFR 23.12.

The definition reads: a diamond is a mineral of pure carbon, crystallised in the isometric system. It adds three numbers. Hardness 10, specific gravity about 3.52, and refractive index 2.42.

Moissanite fails the first clause. It is not carbon. That is not a matter of degree or of trade custom.

The same section adds a second rule that surprises buyers. Even a real diamond cannot be sold as “diamond” unqualified unless it has at least seventeen polished facets.

Then there is the imitation rule. A lab-grown or imitation stone described with the words stone, gem or gemstone needs an equally conspicuous qualifier in front.

The same section says outright that the word “faux” is not an adequate disclosure. Writing “faux diamond” on a listing does not fix the problem.

For lab-created diamonds, the word “cultured” is allowed, but only with a clear and conspicuous qualifier such as “laboratory-created” next to it.

Put together, three phrasings are safe and one is not:

Safe: “Moissanite”, “lab-grown moissanite”, “silicon carbide”.

Safe: “Diamond simulant” or “imitation diamond”, with the stone named.

Safe: “Lab-grown diamond”, when the stone really is carbon and the lab disclosure rides along.

Not safe: “Moissanite diamond”, or a listing tagged diamond with moissanite in the small print. That is the exact claim the guides exist to stop.

This matters to a factory buyer more than to a shopper. The listing text is written by whoever sets up the SKU, often months before the first shipment.

How To Write The Listing Line

Most cases start with one sentence in a product listing, not with a stone. Write that sentence with care.

A safe pattern. Stone name first, then size, then metal. “Moissanite, 6.5 mm, sterling silver.” Nothing in that line can be read two ways.

A second safe pattern. When the stone is a simulant, say so and name it. “Imitation diamond, silicon carbide, 6.5 mm.”

The pattern to avoid. A diamond word in the title and the real stone in a spec tab. Buyers read the title, and so do the platforms.

Adjectives carry the same weight as nouns in these rules. A page that says “diamond-like fire” is making a comparison, and a comparison is allowed.

A page that says “diamond” is making a claim about the stone itself. That is the line that has to hold.

Keep one paragraph of plain text near the top of the page that names the stone. Not a footnote, not a spec tab, not an image caption.

Photography needs the same care. A stone shot at three times actual size can mislead unless the true size is stated next to it.

Examples of safe and unsafe listing lines for moissanite and diamond, showing where the qualifier goes
Three lines that hold, one that does not.

The Numbers, Side By Side

One table beats ten paragraphs. Every figure below comes from a published source, and the source column says which.

PropertyDiamondMoissaniteWhere the figure comes from
ChemistryC, pure carbonSiC, silicon carbideFTC 16 CFR 23.12(a); mineralogy entry
Mohs hardness10about 9.5FTC 23.12(a); mineralogy entry
Refractive index2.422.654 and 2.967, two raysGIA gem encyclopedia; mineralogy entry
BirefringenceNone0.313, 6H formGIA; mineralogy entry
Specific gravity3.52, plus or minus 0.013.218 to 3.22GIA; mineralogy entry
DispersionNot printed on the GIA page read for this article0.104Mineralogy entry only
Heat behaviourStableGradual heating shifts colour from about 65 °C, then it returnsMineralogy entry

The GIA entry for diamond prints 2.42, 3.52 and Mohs 10. The mineral entry for moissanite prints the two refractive indices and the birefringence figure.

Read the third row twice. Diamond has one refractive index because light enters it as one ray. Moissanite splits light into two, and the numbers are the fingerprint of that split.

Density is the quiet difference. Moissanite is lighter than diamond for the same size, which changes how a stone weighs in the hand and how it sets.

Hardness is where trade pages disagree with mineralogy. Many retail pages print 9.25 for moissanite. The mineral reference used here records about 9.5.

Neither number is a scandal. Both sit between corundum and diamond, and both mean the stone is durable for daily wear.

What matters is consistency. If your listing says 9.25 and your supplier’s certificate says 9.5, a buyer who checks will ask which document is wrong.

The dispersion row deserves a warning. The moissanite figure has a source. The diamond sheet read for this article does not print the same figure, so no fair ratio can be worked out here.

What “More Fire” Actually Means

Fire is the rainbow flash you see when a stone moves under light. It comes from dispersion, the way a stone spreads white light into colours.

Moissanite carries a dispersion figure of 0.104 in the mineral reference. That is a real number and it is high for a gem material.

Pages that claim “more fire than diamond” usually stop there. The comparison needs both figures on the same basis, and that is exactly what the retail pages omit.

There is a second optical effect that retail copy almost never mentions. Because moissanite is birefringent, the edges of its facets can appear doubled under magnification.

That doubling is the most useful check in this article. It is visible with a loupe, it needs no machine, and diamond cannot produce it.

Under normal viewing the effect is subtle. In a photo it can read as haze, and in a cheap cut it can read as a soft edge.

Some buyers describe moissanite as “too much fire” in warm indoor light. That is a taste judgement, not a defect, but it matters when a brand’s photography sets expectations.

Practical rule: choose the stone for the photo shoot you plan to run. A high-dispersion stone under a ring light will photograph differently from a diamond.

Comparison chart of diamond and moissanite properties, with the source of each figure marked
One carbon, one silicon carbide. The numbers separate at the crystal.

Three Field Tests And One Lab Memo

Parcel checks are where mixed shipments get caught. Three tests do most of the work, and none of them needs a gem lab.

The heat pen can lie. Moissanite carries heat much like diamond, so a thermal tester may call it diamond. A pass from that pen is not proof.

Warm it and watch. Gradual heating shifts a moissanite’s colour from around 65 °C, and the colour returns as it cools. This is the field version of a known trait.

Measure conductivity. Electrical behaviour separates the two far more cleanly than heat does. Instrument makers sell exactly this check for that reason.

Look for the doubles. Under a loupe, the facet junctions of a birefringent stone can show a doubled edge. Diamond never does.

None of these replaces a grading report on a stone that carries one. For a bridal programme, the memo travels with the stone and names the lab.

For a fashion programme, the practical substitute is written procedure. Name the stone on the purchase order, check three stones per lot, and keep the record.

The failure mode is not a clever fake. It is a lazy invoice that says “CZ/diamond” and leaves the warehouse to guess.

Keeping A Lot Consistent

One good stone proves nothing. A jewellery order lives or dies on the fifth hundred piece, not the first.

Grown stones come from boules, and boules vary. Colour can drift between growth runs, and size steps can land a tenth of a millimetre off.

Ask how the supplier sorts. A lot sorted by hand into colour bands behaves better than a lot poured from one bin.

Ask for the size step in writing. A 6.5 mm stone and a 6.4 mm stone look the same loose, and different in a calibrated setting.

Photograph the first lot against a grey card. When the second lot arrives, that photo settles the argument in a minute.

Keep one stone from each lot in a labelled bag. This is the cheapest quality record a small brand can hold.

None of this is exotic. It is the same parcel control used for any part that arrives in thousands and gets assembled by hand.

Where The Price Difference Comes From

The gap is structural, not a markup decision. Two different supply chains produce two different cost bases.

Mined diamond runs through sorting, grading and a trade with its own price conventions. Lab-grown diamond adds a growth cost that has fallen as capacity grew.

Moissanite is grown as large silicon carbide crystals and then cut. That is a furnace process with a cutting step, closer to a technical ceramic than to a mine.

Cutting work follows the stone, not the name. A well-cut moissanite takes the same wheel time as a well-cut diamond of the same shape.

Setting work is identical. Prongs do not know what they hold, and a thin girdle chips the same way in either material.

This is why the headline gap narrows in the finished ring. Metal, labour, plating and packaging do not scale down with the centre stone.

The “holds its value” argument belongs to retail resale, not to manufacturing. No factory in Yiwu can promise a resale price, and none should.

What a buyer can control is the cost per sellable piece. That number includes the reject rate on stones and the remake rate on settings.

Which Stone Fits Which Line

Most jewellery catalogues run three tiers. The stone decision follows the tier, and so does the paperwork.

LineStone that fitsWhat the paperwork must say
Entry fashionMoissanite, or cubic zirconia where the price point demands itStone named on the invoice and the listing; plating thickness stated
Mid bridalMoissanite centre with lab-grown accents, or lab-grown diamondStone named, lab disclosure on any diamond claim, report for the centre
Fine bridalLab-grown or natural diamond with a grading reportReport number, lab name, and the four grading factors quoted from it

The middle row is where mistakes concentrate. A mid-tier ring mixes a moissanite centre with small lab-grown accents and calls the whole thing diamond in the copy.

That single line of copy is enough to make the listing misleading, even when the centre stone is honestly invoiced.

Write the accent stones into the same spec line as the centre. The factory brief that covers setting work is the right place, not the marketing deck.

The setting metal carries its own claims. Sterling silver has a legal fineness, and a plated brass ring cannot borrow that word.

If the finish is electroplated rather than a gold layer, say which. The difference between PVD and electroplating is a wear claim, and wear claims get tested by customers.

Gold-filled and vermeil are separate claims again. Vermeil and gold-filled are both regulated terms with thickness rules behind them.

Diagram of three field checks for moissanite: heat pen reliability, colour shift on warming, and doubled facet edges under a loupe
Three checks a warehouse can run. One instrument is not enough.

Six Lines For The Order Sheet

A stone name on its own is not a specification. These six lines turn it into one.

One. The exact stone name, spelled the way the invoice will spell it. Moissanite, lab-grown diamond and cubic zirconia are three different orders.

Two. The document behind it. Which lab, which report number, and whether it covers every stone or one centre stone.

Three. Tolerances. Colour range, millimetre size with a plus or minus, and the stone count per piece.

Four. The metal and the finish claim, in the same sentence as the stone. Sterling silver 925, vermeil with its thickness, or a named plating process.

Five. The sampling rule. Three stones checked per lot, one photo kept, one record signed.

Six. What happens at failure. Replacement, credit or re-cut, and who pays the freight in each case.

Line four is where most disputes start, because the stone gets all the attention and the metal gets the fine print.

A buyer who writes these six lines can hand the same sheet to two suppliers and compare real offers rather than two different products.

STONE AND CLAIM

Send me a stone quote, a listing draft or a supplier report. I will check whether the stone name matches the claim and whether the numbers agree with the standard reference. Then I will name the line that is missing. No cost, no obligation.

Check My Listing

What This Article Does Not Settle

Four questions come up in every moissanite enquiry, and none of them can be answered from a spec sheet.

Resale. A secondary market price is a market fact on the day of sale, not a property of the stone.

Insurance. A valuation for cover is written by an appraiser, and appraisers work to their own rules.

Brand acceptance. Some retailers refuse simulants in bridal ranges as policy. That is a commercial choice, not a legal one.

Customs treatment. Classification of lab-grown and simulant stones differs by market. Ask your broker rather than a supplier.

Everything else in this article is checkable: the chemistry, the legal definition, the physical numbers, and the three field tests.

Questions Buyers Ask

Can moissanite be called a diamond?

Not in the United States. The federal definition requires a mineral of pure carbon, and moissanite is silicon carbide. An unqualified diamond claim on a moissanite listing is the clearest case the guides cover.

Is moissanite a fake diamond?

It is a simulant, which is a neutral trade word. It looks like a diamond and is a different material. Calling it faux is not enough disclosure, and calling it a diamond is worse.

Which stone is harder?

Diamond, at 10 on the Mohs scale. Moissanite is listed at about 9.5 in mineral references, and many retail pages print 9.25. Either way it sits above corundum and below diamond.

Does moissanite pass a diamond tester?

A thermal tester may read it as diamond, because the two conduct heat similarly. Electrical conductivity and visible birefringence separate them far more reliably than a heat pen.

Is moissanite always cheaper?

Usually at the stone line, and the gap narrows in the finished ring. Metal, labour and setting cost do not shrink with the centre stone, so a cheap stone does not make a cheap ring.

Will a jeweller service a moissanite ring?

Most will size and re-tip a setting regardless of the stone. Insurance replacement and brand warranty are the two that vary, so confirm before the order rather than after.

Questions & Comments

We read every one and reply within 24 hours

A stone quote and a listing draft rarely agree. Send both, and I will mark the line where the claim stops holding.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x