Moissanite vs Cubic Zirconia: Hardness, Weight, And Wear
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Moissanite vs Cubic Zirconia: The Two-Year Test

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 16, 2026 · 10 min read

Two white stones sit on the same bench. One keeps a sharp edge for years. The other softens at the edge.

Moissanite is silicon carbide, written SiC. Cubic zirconia is zirconium dioxide, written ZrO2. Both are grown, and neither one is a diamond.

The first difference a buyer feels is weight in the hand. The second shows up much later, at the edge of a facet.

This page sets the two stones side by side. It covers the constants, the size trap that comes with the weight, what wear does, and the tests that separate them.

Beige studio layout with two groups of loose round stones, a steel loupe and a dial caliper, drawn to show one bench holding both stones
Two stones, one bench. The parcel in front is weighed in grams, not carats.

The Short Answer

Moissanite is the harder stone at 9.5 on the Mohs scale. Cubic zirconia runs 8.0 to 8.5. The gap is at least a full point on that scale.

Both stones handle a ring. Neither one crumbles in a drawer. The difference appears slowly, as a change on the facet edge.

The optical difference is just as firm. Moissanite splits light twice, because its crystal does not behave the same in every direction. Cubic zirconia does not split light at all.

The weight gap runs the other way. Cubic zirconia is the heavier stone for the same width, and that changes how a stone is ordered.

So the decision comes down to two questions. Do you need the extra hardness, and can your bench work in millimetres?

Nothing here decides which stone you should like. It decides which stone you can promise a wear life for.

What Each Stone Actually Is

Moissanite is silicon carbide. Natural SiC exists, and it is rare enough to be a collector item. Henri Moissan found it in 1893, in rock from a meteorite crater.

Almost every stone sold as moissanite today is grown. Charles and Colvard started selling it in 1998, and the first patents ran out by 2018.

That expiry matters to a buyer. Several growers now make the rough, so two quotes can differ a lot for the same size.

Cubic zirconia is zirconium dioxide in a cubic shape. Pure zirconia does not hold that shape at room temperature, so a stabiliser goes into the melt.

The usual stabilisers are yttrium oxide and calcium oxide. Two recipes give two stones with slightly different numbers, which is why published values come as ranges.

Commercial CZ starts in 1976, with the skull crucible method from the Lebedev institute. By 1980 output was about 60 million carats a year.

PropertyMoissaniteCubic zirconia
Chemical formSiC, silicon carbideZrO2, zirconium dioxide
Mohs hardness9.58.0 to 8.5
Specific gravity3.218 to 3.225.6 to 6.0
Refractive index2.654 and 2.9672.15 to 2.18
Dispersion0.1040.058 to 0.066
Birefringence0.313None, the crystal is cubic
Panel listing composition, Mohs hardness, specific gravity, refractive index, dispersion and birefringence for moissanite and cubic zirconia
Six rows, two stones. Row three decides how the order is written.

Read the third row first. A CZ of the same width weighs about 1.7 to 1.9 times what a moissanite of that width weighs.

Read the last row second. A birefringence of 0.313 is strong enough for the eye to catch the doubling on a faceted stone. A cubic crystal has one refractive index, so a CZ never doubles.

Dispersion is the fire in the stone. Moissanite throws 0.104 and CZ throws 0.058 to 0.066. A diamond sits at 0.044, so both stones throw more colour than the thing they copy.

Hardness is the only row where the gap runs the other way. It is also the row that decides what the stone looks like after two winters.

The Size Trap: Same Carat, Different Diameter

A carat is a weight, not a width. One carat is 0.2 grams, whatever the stone is made of.

Two stones of the same weight therefore take up different volumes. The heavier material needs less space for that mass.

Run the arithmetic on the two specific gravities. One carat of moissanite at 3.22 takes about 0.062 cubic centimetres.

One carat of CZ at a gravity of 5.8 takes about 0.0345 cubic centimetres. The CZ volume is a little over half the moissanite volume.

Diameter follows the cube root of volume, not the volume itself. Work that through and the CZ comes out 17 to 19 per cent narrower across the table.

That is the trap. Order one carat of each, and the CZ arrives visibly smaller in the same seat.

The fix is simple, and the trade already uses it. Write the size in millimetres, with a tolerance, and never in carat alone.

Two circles drawn to scale for one carat of moissanite and one carat of cubic zirconia, with a note that the CZ circle is about a fifth narrower
One carat each, drawn to the same scale. The width is where the two part company.

A setter works from the diameter. A 6.00 mm seat takes a 6.00 mm stone, and the seat does not care what the parcel weighed.

Measure across the girdle, not across the table. A caliper on the girdle gives the number the seat needs, and it is the number the sieve sorts by.

So the order line reads 5.50 mm, plus or minus 0.05 mm. A carat figure leaves the factory free to send either stone.

The weight also changes how a parcel is counted. Ten grams of CZ holds fewer stones than ten grams of moissanite, because each stone is heavier.

A buyer who prices by gram and compares against a carat quote gets a mismatch. Nothing in that mismatch is about price; it is about mass.

What Two Years Actually Does

Wear on a faceted stone starts at the edges. Each facet meets its neighbour along a thin line, and that line goes first.

Moissanite at 9.5 holds the line longer. CZ at 8.0 to 8.5 rounds it over sooner, and the change shows under a loupe.

A rounded junction scatters light instead of reflecting it. The stone does not go cloudy in any chemical sense. It loses the crisp flash at the edge of each facet.

A loupe and a bright lamp will show that change. Tilt the stone until a facet line catches the light. A sharp line is new, and a soft one has worn.

The second sign sits on the flat faces. A polished CZ carries fine marks, and the marks on one stone run in the same direction.

The third sign is a chip. CZ has no cleavage, so it does not split along a plane. It is brittle, though, and it breaks with a curved, shell-like fracture.

A thin girdle left open by the setting is where that chip appears first. The girdle is the widest point of the stone and the usual point of contact.

None of this is a fault in the material. It is the shape of normal wear, and it belongs in the after-sales terms.

A stone that chips on the girdle in month three is a breakage. A stone whose facet edges have softened after two years is wear.

Moissanite is not immune, and no supplier should claim it is. The stone is harder, so two years leave less of a mark on the edge.

One moissanite habit belongs in the care notes. Warm the stone to about 65 °C and the colour can shift for a while, then return.

A repair bench that solders close to the setting needs to know that. So does a buyer who stores stones near a heater.

Storage belongs on the same card. A stone of 8.0 to 8.5 hardness will mark a pearl or an opal in a drawer. Keep the soft stones in their own bag.

If the parcel is graded on a letter, none of this can be checked at goods-in. The reason is on the page about why a letter grade on CZ cannot be checked.

How A Test Tells Them Apart

A thermal tester settles the CZ question in one touch. CZ is a heat insulator, so the needle does not move.

The probe needs contact. Dirt, a closed back or a thick bezel can all stop a reading, so clean the stone and touch the table.

Diamond and moissanite both carry heat well. Both read positive on the same tester, which is where that test stops being useful.

Telling moissanite from diamond takes a second step. Birefringence gives it away: look through the table and the back facets can appear doubled.

Not every stone shows it on every axis. Turn the stone and watch for a doubled edge on the far side of the pavilion.

Electrical resistance is the other route. Moissanite carries current far less freely than diamond, and a meter can read the gap.

So the order of tests is short. Thermal first, to remove CZ. Then doubling or resistance, to part moissanite from diamond.

TestWhat it showsWhich pair it parts
Thermal probeHow freely heat moves through the stoneCZ from diamond and moissanite
BirefringenceA doubled edge behind the tableMoissanite from diamond
Resistance meterHow freely current movesMoissanite from diamond

A shop that owns only a thermal tester can tell you the stone is not CZ. It cannot tell you the stone is diamond.

Ask which test was run before you accept a spoken answer. A thermal reading is not a stone report. The checks a diamond order needs are listed on the comparison a diamond buyer runs first.

A mounted stone is harder to read. A closed setting hides the pavilion, so the doubling test needs an open back or a loose stone. Ask for a loose stone when the reading matters.

Raw constants are worth reading once. The optical figures sit on the reference page for silicon carbide. The ranges for CZ sit on the reference page for zirconium dioxide.

What It Costs You Per Piece

No percentage belongs in this section. A stone price has three parts, and the parts move for different reasons.

The first part is the rough. Moissanite rough costs more per carat, because single-crystal SiC grows slowly in a furnace.

The 2018 patent expiry widened the supplier list. It did not make the growth any faster, so the rough stays the costly input.

Cutting is the second part, and it is where the surprise sits. At 9.5, moissanite wears the polishing lap faster, so a cutter spends longer on each stone.

With CZ the rough is cheap. The cutting carries the cost, because the stone is brittle and a thin girdle chips on the wheel.

Loss is the third part, and buyers forget it. Every chipped stone in a lot is a stone you paid for and cannot ship.

A CZ parcel with a high breakage rate therefore costs more than its quoted piece price. The yield takes back the difference.

One cost sits outside the three parts. Freight is charged on weight, and a CZ parcel is the heavier one. That line belongs in the shipping column, not the stone column.

Setting cost barely changes with the stone. A 6.00 mm seat takes either one, and the setter spends the same time on the claws.

Where setting cost does change is the style. A bezel covers the girdle. A tall prong setting leaves the girdle open to the next hard surface it meets.

So compare two quotes on the same six lines. A quote that names a carat weight and a grade letter cannot be compared with anything.

Six Lines For The Spec Sheet

These six lines replace every adjective on the listing. Each one can be measured when the lot lands.

LineWrite thisWhy it matters
StoneSilicon carbide, or zirconium dioxideThe trade name alone hides the material
SizeDiameter in mm, plus a toleranceA carat figure hides the width gap
Hardness9.5, or 8.0 to 8.5 on MohsSets the wear you should expect
TestThermal first, then doubling or resistanceNames the method, not the result
Wear lineSoftened facet edges are wear, chips are notSplits normal wear from a claim
ReplacementOne-for-one on a chipped girdleGives the reject rule a number

Put the six lines on the page the workshop signs. Keep the approved sample beside it, and keep the sample for the life of the design.

Keep one approved stone in a labelled bag with the sheet. On a repeat order the bag comes out first, and the new lot is compared against it, not against a photo.

Then check each lot against the sheet. A pre-shipment check can measure a diameter and count stones. It cannot see a softened facet edge, so the sample carries that job.

Two of the lines catch most of the trouble. The millimetre line kills the size trap, and the wear line kills the argument about a dull stone.

A buyer who wants the background on the harder stone can read what a moissanite parcel looks like at goods-in.

Setting work is the other half of the cost, and the sourcing guide that covers setting work explains what a factory brief has to say.

TWO STONES, ONE SPEC

Send me the stone line from your order, or the two quotes you are holding. I will say which of the six parts is missing, whether the two stones can be compared at all, and what to write so a sample settles it. No cost, no obligation.

Check The Pair

Questions Buyers Ask

Is moissanite harder than cubic zirconia?

Yes, by at least a full point on the Mohs scale. Moissanite is 9.5 and CZ is 8.0 to 8.5, so the CZ edge rounds over sooner under the same wear.

Does cubic zirconia go cloudy over time?

The stone does not cloud in a chemical sense. Its facet junctions round over and its girdle chips, and both read as a loss of flash. Marks from polishing run one way on each stone.

Can a thermal tester tell moissanite from diamond?

No. Diamond and moissanite both carry heat well, so both read positive. A thermal tester separates CZ from the other two, and there it stops.

Why is one carat of CZ smaller than one carat of moissanite?

Because CZ is heavier for its volume. At a gravity of 5.6 to 6.0 against 3.218 to 3.22, the same weight of CZ takes less space, so the stone is narrower across.

Which stone suits a ring worn every day?

Moissanite holds its edge longer, so it shows less wear after two years. CZ costs less to replace, and a bezel that covers the girdle protects either stone.

What should the invoice say?

The material name, the diameter in millimetres with a tolerance, and the test that was run. A grade letter and a carat weight alone cannot be checked at goods-in.

Questions & Comments

We read every one and reply within 24 hours

Is your stone line a carat weight and a letter? Paste it here and I will mark which of the six lines is missing before a sample gets approved.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x