What Is Rattan: Species, Grades And The Order Sheet
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Rattan: Species, Grades And The Order Sheet

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 11, 2026 · 12 min read

Rattan is a climbing palm. Its stem is cut into poles, boiled, dried and woven, and most of it starts in an Indonesian forest.

A rattan chair and a rattan basket come from the same plant and go through the same mill. What changes is the grade of the pole and the patience of the drying shed.

This article answers the simple question first. Then it gives the numbers and the two documents a buyer has to hold a supplier to.

Studio still life on a beige backdrop of a bundle of pale rattan poles beside a shallow woven rattan basket
One plant, two products: poles for the frame, split cane for the weave.

The Short Answer

Rattan is the trade name for about 600 species of climbing palm in the Old World tropics.

The stem is solid and usually 2 to 5 cm across. It keeps that width from base to tip, because a palm does not add a new ring of wood each year.

That one fact explains the material. A pole can be bent, split and joined without being planed square first.

About one species in five is used in trade. Almost all supply still comes from wild forest, not farms, which is why two shipments of the same grade rarely look alike.

So the word tells you the plant. It does not tell you the species, the grade, the moisture or the price. Those four are the order.

A Stem, Not A Timber

Three words get mixed up in listings, and the mix-up costs money.

Rattan is the inner reed of the stem. Cane is the outer skin of the same stem. Wicker is not a material at all. It is a way of weaving.

A weaver can make wicker from rattan, willow or bamboo, and the label often hides which one was used.

Rattan is also not bamboo. Bamboo is a hollow grass with a wall. Rattan is solid through the section. A buyer who orders a bamboo look and receives bamboo has bought a different product.

Because the stem is solid and even, one pole splits into three products. The skin becomes binding and flat weave. The core becomes basket strand. The round pole becomes frame.

Pricing follows that split. A kilo of skin and a kilo of core are not the same buy. A quote that never names the form is a quote for an argument.

Strength sits in the outer fibres. The middle is softer and holds water longer. A scrape on the skin therefore matters more than the same scrape on the core.

Where The Pole Comes From

Indonesia holds about 80 % of the world raw material, on the FAO’s own count.

The country has 306 species, and only 28 of them are used in trade, according to its Ministry of Industry.

In 2024 the ministry put Indonesia’s exports of rattan products at USD 158.5 million. That was 42.2 % of a world total of USD 375.6 million.

The rest comes from Malaysia, the Philippines, Vietnam, Laos and a growing area of plantation in southern China.

Very little of it is farmed the way timber is farmed. A cutter works in mixed forest and pulls whole poles down out of the canopy.

The poles reach the mill with species mixed together and in different sizes. The first job at the mill is sorting, not sawing.

That matters to a buyer in a dull way. A supplier who cannot name the species in a bundle has not sorted it. That bundle is the least stable thing to buy on the market.

Four Grades And Five Diameter Classes

Mills sort rattan twice, and the two sorts answer two different questions.

The first sort is quality. Grade A is clean, with no stain and no dark spot. Grade B carries two or three marks. Grade C carries plenty. A fourth pile is rejected cane, often sanded and re-graded later.

The second sort is size. For poles of 20 mm and up, the manual lists five diameter classes. They run from 40 mm and above, down through 35 to 39, 30 to 34, and 25 to 29, to 24 mm and below.

Length follows size. A pole of 20 mm and up is cut 3 m long. A pole of 19 mm and less is cut 6 m long.

Chart of four rattan quality grades from A to reject and five diameter classes from 40 mm and above to 24 mm and below
Two scales, one bundle. The grade is about looks, the class is about structure.

Both sorts belong on the order. “Grade A” alone is a promise about appearance. It says nothing about whether the pole will take the bend in your drawing.

Size decides that. A 24 mm pole and a 40 mm pole carry different loads, and the thin one will not hold the same seat.

Add a tolerance to both lines. A mill that ships a bundle sitting between two classes has met no spec, unless the spec allowed the mix.

SortLevels in the manualHow it is judgedHow to write it
Quality gradeA, B, C, rejectStain and dark spotsGrade A, no dark spot at a node
Diameter classFive, from 40 mm to below 24 mmMeasured diameter, mm30 to 34 mm, tolerance 2 mm
Pole length3 m or 6 mFollows the diameter group3 m poles, 20 mm and up

The table looks fussy until the first claim. A frame that splits at a node is usually a pole that was cut in the wrong class, dried too fast, or both.

Oil Curing: The Step That Sets The Price

Fresh rattan is wet. The manual puts green cane at 76 to 98 % moisture, and cane at that level will stain inside a day.

So the mill boils it. The usual medium is diesel, held between 60 and 150 °C, for 10 to 30 minutes depending on species and diameter.

The boil does four jobs at once. It kills insects and fungi, it draws wax and gum out of the skin, it speeds the drying, and it evens out the colour.

The poles then go out to dry for 10 to 14 days. Someone turns the stack on the third to fifth day so both sides dry at the same rate.

The batch is ready when the surface turns yellow, the weight drops and the pole rings when tapped. The manual puts the target below 20 % moisture.

Large poles of good grade get a second step. They are smoked overnight with sulphur dioxide, at about 1 kg of sulphur per 500 poles. That bleaches the skin to ivory and adds protection.

That is the whole line. There is no hidden chemistry in it, and a mill can show every step to a visitor.

Flow chart of cutting, boiling, drying and sulphur fumigation with temperatures, drying days and moisture cut-offs
Four steps, four numbers. These are the figures a mill can be held to.
StepWhat it changesFigure to check
BoilWax, insects, colour10 to 30 min at 60 to 150 °C
DryWater in the cane10 to 14 days, turned on day 3 to 5
SortGrade and classFour grades, five classes
FumigateSkin colour, pestsAbout 1 kg sulphur per 500 poles
StoreMoisture creepDry shed with air through it

Two questions separate a mill from a trader. Ask what medium they boil in, and ask for the moisture reading taken on the day of packing. A trader can answer neither without calling someone.

Why A Pole Bends, And Why It Splits

Rattan bends because it is a bundle of long fibres in a soft matrix, not a stack of cells in rings.

The manual describes the stem as roughly half soft tissue. Fibres and vessels make up most of the rest, and the fibres are densest near the skin.

The same structure explains the failure. Water sits in the wall and in the cavity, and the fibre saturation point is around 30 %.

Below that point the pole gets stronger as it dries. At 17 % moisture it is about one and a half times as strong as green cane.

It also shrinks. Across the diameter, green cane loses an average of nearly 45 % of its width on the way to air dry. Along the length it barely moves.

That mismatch is the crack. The outside dries first and pulls in, the core stays wide, and the pole splits between the two.

A slow dry and a turned stack spread the strain. A hot shed and a thick bundle concentrate it, and the split shows up at a node a week later.

Bending fails the same way. The manual notes that a bent pole usually fails by shear along the grain, and that rattan has little resistance to splitting.

The bend radius in your drawing is therefore a material question, not a design taste. A tight bend on a thin, fast-dried pole is a claim for replacements.

Mould Is The Claim You Will Actually Fight

Staining fungi arrive within 24 hours of cutting. The manual is blunt about the route in: a cut end, a bruise or a split, and the stain reaches the core.

Three conditions let it grow. Moisture above 30 %, storage below 40 °C, and food in the cane such as starch.

Take away one of the three and it stops. Below 20 % moisture the fungus will not grow, even in a warm shed.

That is why “kiln dried” is not a spec. The question is the number, the sample and the day it was read.

The claim usually arrives a month after the container. The cartons look fine, the frames have grey bloom at the joints, and the buyer hears a story about humidity at sea.

Sea air is rarely the cause. A sealed carton holding cane at 26 % moisture is a small greenhouse, and the voyage is only the time it needed.

Put three things on the order: a moisture figure below 20 % at packing, a sample size, and the meter reading recorded per carton.

Then spend ten minutes on an inspection that opens cartons and reads nodes. A stained node shows long before a whole frame turns grey.

The Paper That Travels With It

Rattan finished goods leave Indonesia under a rule that surprises most first-time buyers.

Regulation 89/M-DAG/PER/10/2015 treats rattan products as forestry industrial products. Mats and curtains under 4601.22, baskets under 4602.12, rattan seats under 9401.51 and rattan furniture under 9403.81 all sit in Group C.

Group C is the light group. It does not need the V-Legal document, and it does not go through the technical criteria that Group A wood products must meet.

That single fact changes the paperwork. A buyer who asks a rattan exporter for a V-Legal document is asking for a paper the product does not carry.

Check the current text with the exporter anyway. These lists get amended, and the 2015 rule is a frame, not the last word.

The destination adds its own layer. In the United States, rattan is a plant product. The Lacey Act declaration is filed in ACE for the plant products on the APHIS list. The importer files it, not the factory.

Packaging is separate again. Crates and pallets made from raw wood have to carry the ISPM 15 mark. The pest risk travels with the pallet, not the furniture.

Some destinations also ask for a phytosanitary certificate. That paper follows the ISPM 12 rules, and the plant protection office in the exporting country issues it.

None of this is exotic. It is four questions, and the answers sit in documents that a real exporter already holds.

Where The Quote Moves

Two suppliers can quote the same chair with a 40 % gap and both be honest.

The manual lists the price drivers in order: species, form, grade, size and colour. A quote that omits the species has left the largest driver out.

Form matters as much. Raw pole, split skin, core strand and finished frame are four markets with four price bases.

The gap between a raw pole and the piece in a shop can reach ten times. Most of that gap is labour, drying and freight, not material.

The industry is small-shop heavy. The FAO outlook puts more than 90 % of factories under 50 staff, which is why capacity and consistency move together.

So compare quotes on one basis. Same species, same grade, same class, same moisture, same carton count, same trade term.

Then ask for monthly capacity in the same message. A workshop that weaves 300 pieces a month and quotes 3,000 has subcontracted the difference, and the second workshop has never seen your sample.

Six Lines For The Order Sheet

A sample tells you what the mill can do once. The order sheet tells it what to repeat.

One: species and grade. Name the species, then the grade, then the defect rule. “Grade A, no dark spot at a node” is a spec. “Grade A” is a mood.

Two: diameter and length. Give the band in millimetres, the length and a tolerance. A 30 to 34 mm pole cut at 3 m is a clear instruction.

Three: moisture at packing. Below 20 %, measured on a sample, recorded per carton, read on the shipping day.

Four: curing method. Boiled, steamed or untreated, with the medium named. The method explains the colour, so it belongs beside the colour line.

Five: colour reference. Send a physical sample. “Natural” covers everything from pale straw to deep honey, and a photograph cannot settle it.

Six: carton and drop test. Piece count, gross weight, and the test you will accept. A drop test on a full carton is the cheapest proof that the frame survives a pallet.

Put the six on one page, because a spec that runs to four pages gets read once. One page that carries all six lines is what the line supervisor will actually use.

Checklist of six rattan purchase order clauses covering species, diameter, moisture, curing, colour and carton testing
Six lines, each one aimed at a failure that shows up after the container lands.

For a mixed order, put the frame material on the same page. A rattan seat on a timber frame that will not move needs its own moisture line. A furniture programme in China usually buys both from one workshop.

Freight is the last line nobody writes. Bulky frames pay for air, so the container fill for bulky frames decides part of the landed cost before the material does.

MOISTURE AND GRADE

Send me a rattan quote, a grading sheet or the moisture record from your last shipment. I will check the species, the grade, the diameter band, the curing method and the packing figure, then tell you which line is missing before the order goes out.

Check My Spec

Questions Buyers Ask

Is rattan a wood or a grass?

Neither. Rattan is a climbing palm, so it is closer to a palm tree than to timber or bamboo. The stem is solid and it keeps the same width as it grows, which is why the pole can be bent without planing.

Is rattan the same as bamboo?

No. Bamboo is a hollow grass with a wall, and rattan is solid through the section. Bamboo also has regular growth ridges, while rattan shows a node ring and a mottled skin. They are not interchangeable in a frame.

What is the difference between rattan and cane?

They are the same plant cut differently. The trade calls the inner reed rattan and the outer skin cane. Cane is thinner, flatter and sold for weave and binding; rattan pole is sold for structure.

What moisture should rattan be at packing?

Below 20 %. Fungus will not grow under that figure, even in a warm store. Between 20 and 30 % it can survive, and above 30 % the cane stains quickly. Ask for the reading taken on the shipping day.

Will rattan furniture mould in a container?

Only if it was packed wet. A sealed carton holds the moisture that the cane carried in. Cane at 26 % will bloom during a normal voyage, and cane below 20 % will normally arrive clean.

Why is rattan furniture more expensive than it looks?

Most of the cost is not the cane. Boiling, 10 to 14 days of drying, sorting, fumigating and hand weaving all sit between the forest and the frame, and the FAO puts more than 90 % of the factories below 50 staff.

Questions & Comments

We read every one and reply within 24 hours

A rattan grade, a moisture reading or a carton photo is enough to start. Post the number your supplier gave you, and I will tell you what it does not cover.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x