Full Tang: Length, Width, And The Claim The Name Hides
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Full Tang: Length, Width, And The Line The Name Leaves Out

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 11, 2026 · 11 min read

Full tang means the steel of the blade carries on through the whole handle, from the point to the butt, so the grip is steel with two scales fixed to it instead of a shell around a short stub.

That is the whole definition, and it is a definition about length. Width, thickness and the way the scales are held on are separate questions.

Most buying mistakes in this category come from that gap. A quotation says full tang, the sample arrives, and nobody can say what was promised.

This article separates the claims, prices the steel, lists how the joint fails, and ends with the lines to put on an order sheet.

Studio still life of a full tang knife on a beige surface, with the steel tang and two rivets visible at the end of the handle
Steel at the butt end is the visible half of the claim.

The Steel Does Not Stop

Pick up a budget kitchen knife and look at the end of the handle. On most of them the steel stops a few centimetres past the bolster, and the rest of the grip is plastic on a hollow shell.

On a full tang knife the steel reaches the end. The tang follows the outline of the handle, and the two handle scales are fixed to its flat sides.

A retailer that sells both patterns describes the result in one sentence. The full thickness of the blade is carried into the tang. The handle ends up at least as strong as the blade, and often stronger, because the blade is thinner.

That is why the pattern appears on knives that get hit, twisted or leaned on. Camp knives, hunting knives, butchers’ knives, heavy chef knives and cleavers.

It is also why the pattern appears in product photography. A strip of steel at the butt end is the cheapest proof a seller can shoot. It reads as quality even when the knife is poor.

One Word, Two Claims

Here is where the money moves. The phrase fixes the length of the steel. It says nothing about the width.

The reference definitions keep the two apart. The standard description of a tang says a full tang runs the full length of the grip. It may or may not be as wide as the handle.

When the steel is also full width, you can see it along the belly, the back and the front. The trade name is a slab tang.

When it runs the full length but stays narrow inside the handle, it is a through tang. Same length claim, less steel, a rounder grip.

Both descriptions are honest. They are not the same knife, and they do not cost the same to make.

The weight gap is easy to work out. Steel runs at about 7.85 grams per cubic centimetre, so a tang can be weighed before it is cut.

Take a handle 110 mm long and 22 mm wide. At 2.0 mm thick the steel is 4.84 cubic centimetres, about 38 grams. At 2.5 mm it is 6.05 cubic centimetres, about 48 grams.

Ten grams at the back of a knife changes how it feels in the hand. On a 200 gram knife it is five percent of the tool, all of it behind the grip point.

It also changes the steel bill. A slab tang takes its handle area from the same sheet as the blade, and that sheet is bought by weight.

A through tang takes a narrow strip and leaves the rest of the sheet for other parts. At twenty thousand pieces, the difference reaches the unit price.

ConstructionSteel in the handleTypical useCost and risk
Slab tangFull length, full width, visible at belly, back and frontCamp, hunting and butchers’ knivesMost steel and most finishing; strongest joint
Through tangFull length, narrow, hidden under the scalesKitchen and hunting lines with round gripsLess steel, lighter, same length claim
Tapered full tangFull length, thinned towards the buttHigh-end fixed bladesSaves weight, adds a grinding step
Partial or half tangOne third to two thirds of the handleBudget kitchen and utility knivesLeast steel; the joint becomes the weak point
Stick or rat-tail tangA narrow rod, often to a pommel nutClassic and decorative patternsLightest and cheapest; weakest under side load

Read a quotation against that table and one question answers itself. Which row am I buying?

Four silhouettes comparing a slab tang, a through tang, a tapered full tang and a stick tang inside the same handle outline
Four handles, four steel shapes, one phrase on the specification.

Where The Price Difference Comes From

Two factories quote the same drawing and one lands fifteen percent higher. The tang is usually part of the reason, and it is never the whole reason.

Steel mass. The slab tang figure above is the start. A full width tang takes more steel out of the blank. Steel is usually the largest single material cost in a mid-range knife.

Sheet yield. Blanks are nested on a sheet. A wide tang pushes the next blank further away, so the same sheet yields fewer pieces. Ask for the blank layout, not just the weight.

Grinding time. A full tang has to be surface ground flat on both faces, because the scales sit on it. A wavy tang shows up as a gap after assembly, and the fix is labour.

Thickness tolerance. This is the number that decides whether the sample matches the production run. One Yangjiang OEM maker states plus or minus 0.1 mm for standard lines, and plus or minus 0.05 mm for high-end or spec-sensitive lines. The tighter figure costs inspection time.

Heat treatment. Thin stock moves in the furnace. That same maker notes that blades under 2.0 mm often need fixtures or straightening. The step goes into the process plan.

Scale area and hardware. A full tang handle needs two scale blanks cut to the tang outline, plus pins, bolts or tubes. Three pins and two tubes are not the same cost, and neither is a Corby bolt against a plain pin.

Finishing. The tang edges are exposed on a slab tang. Every exposed edge is ground, blended and polished by hand. On a full width handle that is the longest hand operation on the knife.

None of these appears in the phrase full tang. All of them appear in the price, which is why a name-based comparison between two suppliers is not a comparison.

Where A Full Tang Fails

A full tang removes one failure mode and leaves four. The handle can no longer snap off at a stub, because there is no stub. What is left is everything around the steel.

Moisture under the scale. Water enters at the front of the handle, where the scale meets the blade, and it does not come out. The steel under the scale rusts, and the first sign is a brown line at the joint or a stain spreading through wood.

A removable scale lets a user take the handle apart and dry it, which is why hunters ask for that feature. Blood and water get between the scale and the tang, and a fixed handle keeps both.

The gap at the front. A joint with a visible gap is a hygiene problem before it is a strength problem. Food and liquid sit in a slot that a brush cannot reach.

Judge it dry and judge it under a lamp. Run a fingernail along the joint from the bolster to the butt on both sides. A step you can feel is a step that will hold water.

The butt end. A full tang puts steel where the hand lands when a knife is dropped. The steel survives, and the shock goes into the pins and the scale corners. A cracked scale at the butt is the most common handle complaint on hard-use knives.

Side load at the ricasso. The ricasso is the short unsharpened section between the edge and the handle. It is also where the blade cross section changes, so it collects bending stress.

Bend any knife sideways and the curve starts there. A full tang spreads that load along the handle, which helps, and it does not remove the stress point.

Wood movement. Wood scales swell and shrink across the grain with the seasons. A joint that is flush in July can stand proud in January, and the proud edge is what catches on a cloth and lifts.

Stabilised wood, laminated wood, Micarta and G10 move less. They also cost more, and the difference in the quotation is usually the answer to a handle that opened after six months.

There is no published standard that tests a handle joint on a fixed knife. The cutlery standards cover the blade, not the assembly. ISO 8442-1 sets requirements for cutlery used to prepare food, and ISO 8442-2 covers stainless steel and silver-plated cutlery. ISO 8442-5 covers sharpness and edge retention.

So the joint test has to be written by the buyer. Two checks are enough to catch the usual failures, and both are cheap to run on a sample.

The first is a soak. Put three samples in water for an hour, dry the outside, then look at the joint line. Rust weeping at the front pin means the seal failed.

The second is a drop. Drop the knife three times from waist height onto a concrete floor, butt first. Inspect the scale corners and the pins, and photograph what you see.

The Balance Trade-off

Extra steel at the back moves the balance point. On a full tang fixed blade the balance usually sits near the ricasso, which is where the hand already is.

That is a benefit on a knife that is gripped and pushed. It is a cost on a knife that is used with the wrist. The mass at the back has to be turned as well as carried.

Two patterns exist to take the weight back out. A tapered tang thins from the ricasso towards the butt. A skeletonised tang has sections cut away, often as a row of holes.

Both trade strength for balance, and both need to be on the drawing. A tapered tang adds a grinding step. A skeletonised tang adds a milling step and a deburring step, and the inside edges must be broken or they start a crack.

Weigh the sample at both ends. A kitchen scale under the blade and a finger under the handle tells you more about balance than any description, and it takes two minutes.

Bar chart comparing the mass of a handle tang at 2.0 mm, 2.5 mm and 3.0 mm thickness for a handle 110 mm long and 22 mm wide
Same handle outline, three thicknesses, 38 to 57 grams of steel.

Reading A Quotation

Most knife quotations are written in the language of the catalogue. That language is fine for a retail listing and too loose for a factory order.

The table below turns six common lines into six questions and six numbers. Each number can be measured on a sample by anyone with a caliper and a scale.

What the quote saysWhat to askNumber to record
Full tangSlab, through or tapered?The construction name, plus a side view drawing
2.5 mm steelWhere is it measured, and what tolerance holds?Thickness at heel, middle and butt, with a plus or minus figure
Stainless steelWhich grade, and what hardness range?Grade code and a hardness range on the finished blade
Wood handleSpecies, stabilised or plain, grain direction?Species name and whether it is stabilised
Riveted handleHow many pins, what diameter, solid or tube?Pin count, diameter in millimetres, material
Hand finishedIs the joint flush, and what gap is accepted at the front?A written pass rule for the joint line

Two of those rows decide most disputes. The thickness row decides whether the run matches the sample, and the joint row decides whether the handle survives a dishwasher.

Four Questions Before You Approve A Sample

A sample approval is the strongest lever a buyer has, and it is usually spent on colour. Spend it on the four numbers instead.

One. Which construction? Ask for a side view drawing of the tang, not a photograph of the finished knife. The drawing shows length and width together.

Two. What thickness, measured where? Name three points: the heel, the middle of the handle, and 10 mm from the butt. A single figure hides a taper and hides a grinding drift.

Three. How are the scales held? Pins through the tang, bolts, tubes, epoxy, or a mix. Ask for the number and the diameter, and ask whether the pins are solid or hollow.

Four. What does the sample have to survive? Write the soak and the drop test down before the sample arrives, so the result is a pass or a fail rather than an opinion.

Run the checks on the sample you keep. Keep a second sample sealed in a bag as the reference, because the argument at goods-in is about drift, and drift needs a fixed point.

Side view of a knife marking three caliper points on the handle at the heel, the middle and near the butt, with the front joint marked
Three points, both sides, one tolerance. Everything else is an opinion.

For a food-contact product, the handle joint sits inside the scope of the rules for materials that touch food. The food contact rules for kitchenware are the place to check what the scale material and the adhesive have to meet.

The Order Sheet

Six lines make a tang buyable. They fit on one page, and each one closes a gap that the name leaves open.

One. The construction: slab tang or through tang, with the tang outline dimensioned. No phrase only.

Two. The thickness with a tolerance, at three named points, measured with a caliper.

Three. The steel: grade code and a hardness range on the finished blade. What 18/10 means on a blade is worth reading before that line is written, because a grade number alone does not fix hardness.

Four. The scale: species or grade, stabilised or not, and how the pair is matched for colour.

Five. The hardware and the joint: pin count, diameter, material, and a pass rule for the gap at the front and at the butt.

Six. The tests: soak, drop and lateral bend, each with a pass figure and a name against it.

Put the same six lines on the inspection order. The final check before loading is only as good as the list it works from. A list built on the word full tang has nothing to measure.

The sheet matters even more when a buyer compares two steel labels on the same handle. The difference between 18/8 and 18/10 changes the blade cost and not the tang, which is exactly the kind of split a name-based quote hides.

One more line belongs on the sheet, and it is not about steel. The specification sheet a factory builds against is what turns these six items into a document the line supervisor can read.

Then there is the tariff, which ignores all of it. Table knives with fixed blades are classified by handle material and by value, not by tang. The tariff lines for table knives with fixed blades split on those two things.

Rubber or plastic handles land on 8211.91.50, at 0.7 cents each plus 3.7 percent. Short knives valued under 25 cents each land on 8211.91.20, at 0.4 cents each plus 6.4 percent.

So a buyer who switches from wood to plastic changes the duty line. A buyer who switches from through to slab does not. The customs entry will never mention the tang.

Two buyers can hold the same word, the same price and two different knives. The six lines are how you find out which one is in the carton.

JOINT CHECK

Send a knife quotation, a sample photo of the butt end, or the drawing the factory is working from. I will check whether the tang is slab or through, whether the thickness carries a tolerance, and where the handle cost sits in the price. No cost, no obligation.

Check My Spec

Questions Buyers Ask

Is a full tang stronger than a half tang?

For side load, usually yes, because the steel reaches the butt and the load spreads along the grip. The joint and the scale can still fail first, so the tang alone does not settle it.

Do kitchen knives need a full tang?

A heavy cleaver or a butchers’ knife benefits from one. A thin Japanese style blade often does not, and the weight at the back would work against the way it is used.

How much heavier does it make the knife?

On a handle 110 mm long and 22 mm wide, moving from 2.0 mm to 2.5 mm steel adds about 10 grams. That is five percent of a 200 gram knife, all of it behind the hand.

Can I check the tang without cutting the handle off?

Partly. Look at the butt end, weigh the knife against a known sample, and feel the joint. An X-ray or a cut section is the only proof, and few buyers pay for either.

Does full tang change the duty rate?

No. The tariff splits fixed-blade table knives by handle material and by value per piece. The construction of the tang is not part of the classification.

Can a full tang handle be repaired?

If the scales are held by bolts or tubes, a user can take them off, dry the steel and refit them. If they are glued and pinned, repair belongs to a knife maker, not to the buyer.

Questions & Comments

We read every one and reply within 24 hours

If a knife quotation crosses your desk, send it over with a photo of the butt end. I will check whether the tang is slab or through, and what thickness the quote really holds.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x