What Is 18/10 Stainless Steel? What The Label Hides
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is 18/10 Stainless Steel: The Two Numbers Behind The Label

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 11, 2026 · 9 min read

18/10 stainless steel contains 18 percent chromium and 10 percent nickel.

That is the whole meaning of the label. It names two elements and two percentages. It is not a grade number, and it is not a promise about the goods in the carton.

This matters more than it sounds. A buyer who treats the label as a specification will pay a higher price and still have no document to hold anyone to.

This page covers what the two numbers measure, which engineering grade sits behind them, and the four checks that replace the label.

Soft-lit studio still life of stainless steel cutlery on a beige surface
The stamp tells you a recipe, not a batch.

The Short Answer

The first number is chromium by weight. The second is nickel by weight. Iron fills the rest, with small amounts of carbon, manganese and silicon.

Chromium does the protective work. It reacts with oxygen in the air and forms a thin oxide film over the surface. Scratch that film and it seals itself again, as long as there is enough chromium around.

Nickel does something quieter. It holds the metal in an austenitic crystal structure. That structure keeps the steel soft enough to press into a spoon bowl, and bright enough to take a mirror polish.

In the trade, 18/10 is a nickname. The engineering name for the same alloy family is grade 304. The 304 page on Wikipedia lists 18/8 and 18/10 together as commercial names used in tableware and fasteners.

So the label is real information. It is just not a full specification, and the gap between the two is where buyers lose money.

Two Numbers, One Wide Window

Here is the part most suppliers leave out. Grade 304 does not require exactly 10 percent nickel. It allows a range.

The chemical table on the 304 stainless steel entry gives the ASTM A276/A276M figures. Chromium sits at 18.0 to 20.0 percent, and nickel at 8.0 to 11.0 percent. The SAE grade table gives nickel at 8 to 10.50 percent for the same grade.

Both figures come from published standard tables, and they do not agree to the decimal. That alone tells you the number is a window, not a fixed value.

Now look at what falls inside that window. An 18/8 stamp lands near the bottom. An 18/10 stamp lands near the middle. Both are grade 304. Both meet the same chemistry rules.

A mill aiming at the upper end of the window can print 18/10 on the box. A mill aiming lower can print 18/8. Out of one alloy family, both labels are defensible.

Diagram of the 304 nickel range from 8 to 10.5 percent with the 18/8 and 18/10 marks inside it
Both stamps sit inside the same legal window.
Where the figure comes fromChromiumNickelWhat it is
ASTM A276/A276M, grade 30418.0–20.08.0–11.0Bar stock rules
SAE designation table, 30418–208–10.50General grade table
EN 1.4301, average content18.59A typical melt, not a limit
An 18/8 stamp188Bottom of the window
An 18/10 stamp1810Inside the window

Read the table one more time and the practical problem appears. Nothing in the 304 rules stops a mill from delivering 8.2 percent nickel on steel that a trader later describes as 18/10 steel.

Does that happen? I have not tested a shipment, so I will not claim it does. What I can say is that the label gives a buyer no way to prove otherwise.

That is why the mill test certificate matters more than the stamp. A certificate reports a measured value for the lot in front of you. A stamp reports an intention.

18/10 Is Not 316

A few sellers describe 18/10 as the same thing as 316. Some supplier pages go further, and say 316 is made by cutting chromium to 16 percent and adding 2 percent molybdenum to save money.

Both statements are wrong, and the second one is backwards on cost. Here is the reason.

Grade 316 carries molybdenum at 2.0 to 3.0 percent. Grade 304 carries none. That single element is the difference, and it is the cheapest way to test the claim.

Ask for the molybdenum line on the mill certificate. A 304 lot shows zero or a trace. A 316 lot shows roughly 2 to 3 percent. One line on one document settles it.

The rest of the numbers also rule the swap out. Grade 316 runs chromium at 16 to 18 percent and nickel at 10 to 14 percent. So 316 is lower in chromium than 18/10, not higher.

And molybdenum is not a cost saving. It is an addition that raises the price. A trader who calls a cheaper alloy 316 is not describing a better product.

GradeChromiumNickelOtherMagnet
20116–183.5–5.5Manganese 5.5–7.5, nitrogen 0.25Slides off
304 (18/8 or 18/10)18–208–10.50NoneSlides off
31616–1810–14Molybdenum 2.0–3.0Slides off
430 (18/0)16–180.75 maxNoneSticks

Those figures are the standard ranges for the four grades. They are not readings from any batch I have handled.

Where 316 earns its price is chloride. The 304 entry gives a working limit of about 400 mg per litre of chloride at room temperature. At 60 °C that limit falls to about 150 mg per litre.

Dishwasher detergent is a chloride source, and a hot wash is exactly the condition where 304 has less margin. That does not make 18/10 wrong for a dinner fork. It does mean the word "marine" belongs to 316, not to 304.

18/0, 201 And 430 On The Same Shelf

Two cheaper options turn up in the same catalogue, and both get sold with loose language.

18/0 means 18 percent chromium and no nickel. In practice that is grade 430, where nickel is capped at 0.75 percent. It is ferritic rather than austenitic, so a magnet grabs it. It costs less, dents more easily, and takes surface rust faster in salt.

201 is the other route to a lower price. It reaches an austenitic structure with manganese at 5.5 to 7.5 percent and nitrogen at 0.25 percent, using only 3.5 to 5.5 percent nickel. The austenitic family overview describes the 200 series as the cost-effective route for that reason.

Here is the part that matters on a quotation. 201 cannot honestly be stamped 18/10. Its chromium peaks at 18 percent and its nickel rarely passes 5.5 percent. A seller who offers "18/10 grade at a lower price" is offering one of these two.

The difference does not show in a product photo. A 201 fork and a 304 fork look alike, weigh about the same, and both take a bright polish on the day they ship.

It shows up in month three, in a dishwasher, as pitting around the tines. By then the container has sailed.

If your order has any chance of being 201, name the grade in writing and ask for the certificate before the deposit. The specification sheet a Chinese factory will answer is where that line belongs.

Why A Magnet Cannot Tell You

The magnet test is the most repeated piece of advice on this topic, and it is close to useless as a grade check.

The logic sounds reasonable. 304 is austenitic, and austenitic steel is essentially non-magnetic. So a magnet that slides off means good steel, and a magnet that sticks means cheap steel.

The first half is right and the second half is where it breaks. 201 is also austenitic, so a magnet slides off that too.

The reverse failure is more common and more confusing. Cold working changes the crystal structure. The austenitic overview notes that heavy cold work forms body-centred tetragonal martensite inside the metal.

Martensite is magnetic. A spoon bowl pressed from flat sheet, or a pan body drawn into shape, is worked hardest at the curves. Those areas can pull a magnet even when the sheet was correct 304.

So a magnet that sticks means one of two things, and the test cannot say which. Either the alloy is low in nickel, or the part was formed hard in that spot.

This is how a good shipment gets rejected. The spoons are 304, drawn deep, and the bowls answer a magnet. Nothing is wrong with the steel.

What works instead is duller and more reliable. Read the certificate, then send a coupon to a lab for a chemistry check on the lot you will actually receive.

What The Extra Nickel Actually Buys

Two percentage points is not a small amount when you buy by the tonne. In one kilogram of steel it is 20 grams of nickel that a lower melt would not contain.

That money buys three things, and none of them is strength.

Polish that lasts. Higher nickel takes a deeper, whiter finish and holds it through more wash cycles. That is why the 18/10 stamp appears on forks far more often than on pan bodies.

Drawing margin. More nickel means the metal flows further before it cracks. A deep spoon bowl or a thin-walled cup is easier to press from a melt near the upper end of the window.

A little corrosion room. Extra nickel widens the gap between normal use and the point where pitting starts. It does not remove the limit, it moves it slightly.

Strength is not on the list. Both stamps are grade 304, so both sit in the same tensile range of 210 to 1,050 MPa. That range is set by how hard the part was worked, not by the nickel figure.

Thickness is not on the list either. A 1.5 mm base and a 3 mm clad body can both carry an 18/10 stamp and behave nothing alike on a burner.

So the label earns its keep on the pieces a guest looks at. It earns much less on the pieces a cook works with.

Where 18/10 Still Rusts

18/10 is not rust proof. It is rust resistant, and only while the oxide film stays whole.

Three things break that film, and all three appear in a normal kitchen.

Chloride. Salt left to dry on a hot pan, detergent residue inside a dishwasher, soy sauce sitting overnight. Each one holds chloride against the surface, and the film cannot rebuild while it is being attacked.

Abrasion. Steel wool and harsh scouring pads cut through the film and take metal with them. The film seals again afterwards, but the part is thinner each time.

Heat. Between about 480 and 820 °C, chromium carbides form along the grain boundaries inside the steel. That pulls chromium out of the film where it is needed. The 304 entry calls this sensitisation, and it is the reason welded parts are made from 304L, where carbon is capped at 0.035 percent.

A fork or a pan body is stamped or drawn, not welded, so sensitisation rarely applies to it. It applies to a welded handle, a welded rim, or a repair.

That is why the honest line on a product page is "rust resistant", and not "rust proof". The second claim is the one that brings returns.

The Release Limits A European Buyer Will Ask About

For food contact, the alloy percentage is not the question a lab answers. The question is how much metal moves from the surface into the food.

In the European Union the chain runs through three documents. Regulation (EC) 1935/2004 sets the framework, and Regulation (EC) 2023/2006 sets good manufacturing practice. Metals and alloys then follow Council of Europe Resolution CM/Res(2013)9.

Some countries wrote that resolution into national law. Belgium did it with the Royal Decree of 17 February 2021. A testing house set out the numbers in the published release limits for metals and alloys.

Those limits are stated in milligrams per kilogram of food. Nickel is 0.14, chromium is 0.25, manganese is 1.8, iron is 40, copper is 4.0, molybdenum is 0.12, aluminium is 5.0 and zinc is 5.0.

Bar chart of the specific release limits for nickel, chromium, manganese and iron in milligrams per kilogram of food
Nickel is the tightest line on the list a fork has to meet.
ElementLimit, mg per kg of foodWhy a buyer watches it
Nickel0.14The tightest limit for any 300-series grade
Chromium0.25Rises with long contact with acid food
Manganese1.8The element 201 uses to replace nickel
Iron40Wide, so rarely the failing line
Molybdenum0.12Only present where the grade is 316
Lead, cadmium0.01 and 0.005Contaminants, not alloying elements

Two details decide whether a test report means anything. The first is the area to volume ratio: a flat surface is measured at 6 dm² per kilogram of food. The second is the condition, because the test has to run under the worst use the product is likely to see.

There is also a paperwork point. A declaration of conformity stays valid for five years, as long as the manufacturing process does not change. Change the steel supplier, and the old declaration no longer describes the goods.

This is where the 201 question comes back. Manganese at 5.5 to 7.5 percent in the alloy sits next to a limit of 1.8 mg per kilogram in food. That does not prove 201 fails. It does make manganese the first line a lab will look at on a 201 sample.

Five Lines For The Order Sheet

"18/10" on its own is not something a factory can be held to. It describes a recipe with a wide window and no test attached.

Five lines cover that gap. Add them to the request for quotation, not to the chat thread.

  1. Grade and standard. Write 304 to ASTM A276 for bar, or A240 for sheet. In Chinese nomenclature the same grade is 06Cr19Ni10 under GB/T 20878.
  2. Measured chemistry. Ask for a mill test certificate per lot, with chromium and nickel in the measured column. The typical column is an intention, not a reading.
  3. Release test. Name the elements, the method and the laboratory. Nickel and chromium are enough for a steel grade question.
  4. Thickness and tolerance. State the gauge in millimetres at the point that matters, with the tolerance you will accept. Flatware weight comes from this line, not from the nickel figure.
  5. Finish. Polished, brushed or mirror, plus an approved sample. A word alone lets a cheaper finish replace the sample later.
Five order sheet lines laid out as a checklist for a stainless steel tableware order
Five lines turn a label into something a factory can be held to.

Two related products deserve a different line. A knife blade is a martensitic grade, hardened for edge holding. It is not a 300-series alloy. The comparison of blade steels by hardness and rust is the right page for that half of the order.

If a coloured handle is part of the design, the colour is a coating rather than the steel. Powder coating is one route, and it is worth keeping the two questions apart when the sample arrives.

Four Checks Before A Bulk Order

Documents can be checked at the desk. The goods still have to be checked on the table. Four checks cover most of the risk, and all four fit in an afternoon.

1. Read the certificate against the spec. Chromium and nickel should appear as measured values for the lot. A certificate that repeats the standard range tells you nothing about the metal in the crate.

2. Weigh and measure. Put ten pieces on a scale and measure the thickness at the thinnest point. Nickel does not set the weight of a fork, so a light fork is a thickness decision, not a chemistry one.

3. Run a wet test. Salt water on a cloth, left on the surface for a day, then rinsed. Pitting or orange specks on a 304 piece means the surface was wrong or the grade was. Cheap steel shows this quickly.

4. Rub the finish. Fifty strokes with a soft cloth and a little detergent, in one spot. Compare that spot to the rest of the piece. A polish that dulls early will dull in the buyer’s kitchen too.

Keep one approved sample sealed with the spec sheet and the certificate. When the bulk order arrives, the comparison is against that sealed piece, not against a fresh sample the factory sends later.

If the same container also carries bakeware or serving items, check those against their own spec rather than the cutlery one. The guide to sourcing baking tools in bulk covers that family, and the walk-through of importing from China covers the steps after the inspection passes.

GRADE CHECK

If a quotation says 18/10 and nothing else, the label is doing all the work. Send me the quotation and the mill certificate, and I will read the two against each other. Where the measured column is missing, I will name the three lines to ask for before any deposit leaves your account.

Send The Quotation

Questions Buyers Ask

Is 18/10 stainless steel better than 18/8?

For a table piece, slightly. The extra nickel holds a brighter polish for longer. For a pan body, barely at all, because thickness and core decide how it cooks. Both stamps are grade 304.

Is 18/10 stainless steel the same as 316?

No. Grade 316 carries molybdenum at 2 to 3 percent and 304 carries none. The molybdenum line on the mill certificate settles it in one look.

Does 18/10 stainless steel rust?

It can pit, but it does not rust through in normal use. Chloride, abrasion and heat break the oxide film. Salt left to dry and harsh scouring pads are the usual causes.

Can I tell 18/10 from 18/0 with a magnet?

You can rule 430 in, because it grabs a magnet. You cannot rule much else out. 201 also slides off, and deep-drawn 304 can pull a magnet where it was worked hardest.

Is 18/10 stainless steel safe for food contact?

The grade itself is widely used for food contact. What a buyer has to hold is a release test against the limits in the destination market, not a composition claim.

What does an 18/0 stamp mean?

18 percent chromium and no nickel, which in practice means grade 430. It is ferritic, so a magnet sticks, and it costs less and dents more easily than 304.

Questions & Comments

We read every one and reply within 24 hours

Most 18/10 complaints start with a magnet or a dishwasher. Tell me which piece changed colour, how it was washed, and what the stamp said, and I will say whether the steel or the care was at fault.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x