Nits Brightness: Peak, Sustained and the Window
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Nits Brightness: The Number Behind the Window

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 10, 2026 · 10 min read

A nit is one candela per square metre. The number always needs a window, or it means very little.

Brightness on a specification sheet comes with an unstated question attached: how much of the screen was lit when it was measured.

Measure a small patch and a panel can look spectacular. Measure the whole screen and the same panel has to share its power across a million pixels.

That is why one screen carries three brightness numbers, and why the biggest one is usually the one printed.

Studio still life of a small display panel and a light meter on a beige surface
One panel, three numbers, and a window size nobody prints.

The Short Answer

A nit is a unit of luminance. It measures light leaving a surface, per square metre, in a given direction.

One nit equals one candela per square metre, and the word itself is just a shorter name for the same unit.

Displays are specified in nits because a screen is a surface that emits light. A lamp is specified in lumens, and a room is lit in lux.

Those three units answer three different questions, and mixing them is the first mistake in this topic.

The second mistake is reading a peak figure as though it were a working figure. The certification rules measure peak brightness on a patch covering eight percent of the screen, then measure the whole screen separately.

Both numbers are real. Only one of them describes what a viewer sees with a bright film playing.

One Word, Three Units

Luminance is light leaving a surface. Illuminance is light arriving on a surface. Luminous flux is light leaving a source in all directions.

Nits describe the first. Lux describes the second. Lumens describe the third.

A display is bought in nits because you look at its surface. A lamp is bought in lumens because it lights a room rather than a face.

The same word gets used loosely in shops. A sales page may promise “1,000 nits of brightness” for a screen and “1,000 lumens” for a projector, and the two numbers are not comparable.

A projector spreads its light over a wall from several metres away. Its output in lumens lands on the wall as a much smaller figure in nits, which is why a projector needs a dark room.

Bars comparing an eight percent patch, a full-screen flash and a long full-screen run at three tiers
Three tests, one panel. The gap between them is the honest part.

The reference levels are useful for scale. A calibrated broadcast monitor sits near 100 nits, an ordinary desktop screen runs between 200 and 300, and HDR displays are quoted from 400 up to 2500.

Those figures come from the unit’s own reference notes, and they show how far a marketing number can sit above a working setting.

Why the Window Decides the Number

A panel does not have one brightness. It has a brightness for every picture you show it, because the light is shared.

Drive a small white square in the middle of a dark screen and all the backlight power goes there. Drive a full white screen and it spreads across every pixel.

That is the whole mechanism, and it is why the certification document measures three different things.

An eight percent patch. A small bright area on a dark background, which is what a highlight looks like in a film. This is where the biggest number comes from.

A full-screen flash. The whole screen white for a moment, which is a burst of sunlight or an explosion. It shows how much the panel can do briefly.

A long full-screen run. The same white screen held for minutes. Now heat and power supply set the limit rather than a capacitor.

Only the third number describes a bright document, a white web page or a football pitch on a Saturday afternoon.

A panel reaches the patch figure in two ways. It can drive the backlight harder over a small area, and it can switch off the zones around that area. Both are legitimate, and both cost heat when they are held.

Many screens also dim themselves when the picture is mostly white. That behaviour is what the long-duration test measures, and it is why a bright film can look correct on a panel that renders a white document as grey.

The percentage of the screen that is lit has a name in this trade: the average picture level. A low average picture level leaves headroom for one bright highlight.

What a Tier Label Actually Guarantees

Certification programmes exist because “bright display” means nothing on its own. They turn the three tests into published minimums.

The numbers below are minimums from the certification summary. A product may beat them; it may not fall short and keep the label.

Tier8 % patchFull-screen flashLong full-screen run
400400 cd/m²400 cd/m²320 cd/m²
500500 cd/m²500 cd/m²320 cd/m²
600600 cd/m²600 cd/m²350 cd/m²
10001,000 cd/m²1,000 cd/m²600 cd/m²
14001,400 cd/m²1,400 cd/m²900 cd/m²

Read the top row and the bottom row together. A screen badged at one thousand nits must hold six hundred on a full white screen.

The same document carries a second family of tiers for panels that can switch pixels off completely. There the long run is lower again, because the peak is being asked of every pixel at once.

That is not a trick. It is the physics of a light source feeding a fixed area, written down so a buyer can compare two products honestly.

What the tier does not tell you is how the panel behaves in the middle. Local dimming zones, colour volume and rise time all change the picture without moving the headline number.

Twice the Nits Is Not Twice the Brightness

The eye does not report light linearly. Doubling the luminance makes a screen look brighter, but nowhere near twice as bright.

Perception compresses the range, which is why a 600-nit screen does not look three times brighter than a 200-nit one.

It is also why HDR works at all. The point of high dynamic range is the distance between the darkest and brightest parts of a picture, not the size of one number.

A panel that reaches 1,000 nits in a highlight and 0.05 nits in black gives a deep picture. A panel that holds 600 everywhere gives a flat one.

Then adaptation takes over. Step from a dark room into sunlight and your eyes adjust within seconds, and a phone that looked bright indoors becomes unreadable.

So the number a buyer should compare is not the peak. It is the peak against the black level, measured in the same conditions.

How Many Nits, and Where

The right number depends on where the screen stands, not on how good the panel is. The trade’s usual ladder is a starting point.

Indoors, in controlled light, 200 to 500 nits is enough. A monitor in an office rarely needs more than the middle of that band.

In a shaded position, a covered walkway or a shop window out of direct sun, the figure climbs to 500 to 1,000.

In direct sun the advice is 1,500 nits and up. The ladder as the signage trade publishes it puts full outdoor screens at that level, with no upper bound worth quoting.

Three recommended brightness ranges on one scale: indoors, shaded and direct sun
One scale, three places. The top of the range is where the price jumps.

Treat those bands as a recommendation rather than a test result. They were written by a company that sells outdoor screens, and the right figure still depends on the surface, the angle and the content.

Two practical corrections belong with the ladder. A phone held in shadow reads better than one facing the sun, and a screen behind glass gains a reflection that no brightness rating covers.

The honest way to specify it is to state the place. “Bright enough for a north-facing shop window” is a requirement; “as bright as possible” is not.

Brightness Without Black Is Just Glare

A number on its own does not make a screen readable. What makes it readable is the distance between the brightest white and the darkest black.

Push the whole panel up and the black rises with the white. The picture gets louder without getting clearer, and the eye reads it as glare.

That is why two screens with the same peak can look completely different. One switches zones off, the other lifts the whole backlight.

Reflections matter as much. A glossy panel at 1,000 nits in a bright room can be harder to read than a matte one at 600.

Viewing angle belongs in the same paragraph. Brightness quoted on axis falls away as you move to the side, and a wall display is rarely watched head-on.

Local dimming divides the backlight into zones. The zones behind a bright object go up, their neighbours go down, and the picture gains depth.

The cost is a halo around small bright objects on a dark background. It grows as the zones get bigger, which is why the zone count matters as much as the peak figure.

So the useful comparison is a pair of numbers taken from the same test image: peak white and black level, with the room described.

Five Lines for a Display Order

A brightness claim without its test conditions cannot be enforced. Five lines make it enforceable.

LineWhat to writeWhat goes wrong without it
Peak, with its windowThe figure, the patch size and the background levelA patch number is delivered where a full-screen figure was meant
Sustained figureThe full-screen number, and how long it must holdThe screen dims after five minutes and the site notices
Black levelThe darkest value in the same test imageContrast collapses while the peak still looks impressive
Colour at brightnessColour coverage at the tested level, not just at low levelColours wash out exactly when the screen is driven hard
Surface and viewingAnti-glare treatment, and the angle the figure holds atThe screen is unreadable from the side of a room

The second line is the one that changes a project. A display that holds its number for a minute is not the same product as one that holds it all day.

The fourth line catches a common disappointment. A panel can cover a wide colour range at low brightness and lose it as the backlight climbs.

Two more lines belong on the same sheet for an outdoor unit: the ingress rating of the housing, and the temperature range over which the brightness holds.

Sealing is its own conversation, and an enclosure that keeps rain out is a separate promise from a bright panel behind it.

For a comparison across suppliers, the answers need to line up. One document holding all five lines does that better than five data sheets in five layouts.

Six Lines for the Order

Put the five lines into six sentences, and the brightness on the invoice becomes a number someone can be held to.

Flat card listing six lines a buyer should put on a display order
Six lines. The second one decides whether the screen holds up on site.

One. Give the peak figure with its patch size, its background level and the meter used.

Two. Give the full-screen figure, and the time it must hold before any dimming.

Three. Give the black level measured in that same full-screen test image.

Four. Give colour coverage at the tested brightness, not only at a comfortable level.

Five. State the surface treatment, the ingress rating and the operating temperature range.

Six. Agree the incoming test: which pattern, which distance, and which reading counts as a pass.

The test is worth the paperwork. A batch that meets the peak and fails the sustained figure passes a showroom demo and fails in a window.

Before the order grows, look at the goods in the light they will live in. The market where these panels are sold has bright rooms, and a phone camera is a rough light meter.

None of that replaces a look at the line. A check of the aging rack should include the aging rack, because brightness drifts with hours as well as with settings.

NIT CHECK

Send me the display specification you were quoted and I will read the brightness lines. I will say which window the figure was taken on, what it holds on a full white screen, and which of the six lines is missing. No cost, no obligation.

Check My Screen

Questions Buyers Ask

Is a nit the same as a lumen?

No. A nit measures light leaving a surface per square metre. A lumen measures the total light leaving a lamp. A screen is bought in nits, a lamp in lumens.

Why does a 1,000-nit screen look dimmer than expected?

Because the figure is usually a small-patch peak. On a full white screen the same panel may hold far less, and the room you are in sets what your eye expects.

How many nits do I need outdoors?

The trade puts shaded positions at 500 to 1,000 and direct sun at 1,500 and above. Those are recommendations, and reflections on glass can defeat any of them.

Is a higher nits figure always better?

No. A bright panel with a lifted black level looks worse than a dimmer one with real black, and glare from a glossy surface cancels the gain.

What does sustained brightness mean?

It is the figure the panel holds after minutes of a full white screen, when heat and the power supply have settled. It is the number a working day is spent at.

What is average picture level?

It is the share of the screen that is lit. A low average picture level leaves power for one bright highlight, which is how a small patch reaches a higher number.

Questions & Comments

We read every one and reply within 24 hours

If a screen arrived and the brightness figure does not match what you see, send me the test it was taken on. A patch number and a full white screen are far apart.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x