Jump Rope Size Chart: Length by Height, in cm and Inches
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Jump Rope Size Chart: Height, Handle Position and the Length Between

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 2, 2026 · 9 min read

A jump rope is sized by one measurement: the length of cord between the handles. Every chart you see is a way of guessing that length from your height. Every chart is a starting point, not an answer.

The chart below works backwards from the rule most coaches use. Add three feet to your height for learning, two feet once you can jump continuously, and one foot when you are working on speed.

Warm beige studio still life of a coiled speed rope with slim handles beside a steel tape measure on a plain background
One measurement matters: handle to handle, cord only.

The Rule Behind Every Chart

The rule is simple to state and easy to check. Measure the cord between the handles, not the whole rope, and compare that figure with your height.

For a beginner, the cord should run about three feet longer than the person is tall. One supplier’s guide puts it plainly: rope length between the handles should be around your height plus three feet.

For an intermediate jumper, the figure drops to height plus two feet. That gives enough length for crossovers and side swings without a loop of slack catching the floor.

For an advanced or speed jumper, it drops again to height plus one foot. A shorter cord turns faster, because less cord travels around the arc. That is why double unders get easier with a shorter rope.

LevelCord between handlesHandle height at rest
BeginnerYour height plus 3 ft (91 cm)Bottom of handle at lower chest
IntermediateYour height plus 2 ft (61 cm)Bottom of handle at waist
AdvancedYour height plus 1 ft (30 cm)Bottom of handle at hips

The third column is the part most charts leave out. Stand on the middle of the cord with both feet, pull the handles up, and look at where the bottom of each handle sits. Chest height means a beginner length. Waist means intermediate. Hips means the rope is short.

That check matters because height is a poor summary of a body. Two people at 170 cm can differ by several centimetres in arm span, and arm span is what the cord actually has to travel around.

The Chart, in Centimetres

The table below converts the rule into cord lengths for common heights. Read the row nearest your height and start with the beginner column unless you already jump continuously.

HeightBeginner (height + 3 ft)Intermediate (height + 2 ft)Advanced (height + 1 ft)
150 cm241 cm211 cm180 cm
155 cm246 cm216 cm185 cm
160 cm251 cm221 cm190 cm
165 cm256 cm226 cm195 cm
170 cm261 cm231 cm200 cm
175 cm266 cm236 cm205 cm
180 cm271 cm241 cm210 cm
185 cm276 cm246 cm215 cm
190 cm281 cm251 cm220 cm
195 cm286 cm256 cm225 cm

The same figures in inches: a 170 cm jumper starts at about 103 inches of cord for learning, 91 inches for steady jumping, and 79 inches for speed work.

Two more rows in words, so the pattern is clear. A 160 cm jumper needs about 251 cm to learn, 221 cm to jump steady and 190 cm for speed. A 185 cm jumper needs 276 cm, 246 cm and 215 cm for the same three stages.

The difference between two adjacent heights is 5 cm, which is why the table moves in 5 cm steps and not in 10.

Two things are worth knowing before you use the table. First, the numbers are rounded to the nearest centimetre from a 30.48 cm foot, so a 1 cm difference is not a sizing error. Second, the table assumes the cord is measured with the handles attached and the rope under slight tension. That is how a factory measures it too.

Panel showing the three rope length rules by level and the handle position check at chest, waist and hip height
Three lengths, and the handle position that confirms each one.

Three Checks Before You Cut Anything

Most ropes arrive longer than the chart, on purpose. A rope can always be shortened, and a rope cut too short cannot be lengthened without a new cord.

Check one: the handle position. Stand on the middle of the cord, pull both handles level, and look at where they sit. Lower chest is the beginner length, waist is intermediate, and hips is advanced. This takes ten seconds and needs no tape measure.

Check two: the first jump. Turn the rope slowly and watch where it lands. A rope that clips the floor in front of your toes is short. A rope that touches down well in front of you, or that wraps your feet on the second turn, is long.

Check three: the spare. One supplier’s sizing page suggests leaving three to five inches of extra cord for learning new skills. That spare is useful for crossovers, and it is wasteful once the skills are learned.

The order of those three checks matters. Handle position tells you the length class, the first jump confirms it, and the spare decides whether you trim now or later.

There is also an upper limit worth knowing. One maker states that the cable should never be longer than your height plus an additional three feet. Past that point the rope is not a beginner rope, it is simply too long, and no amount of technique fixes it.

Measure on the floor, not in the air. Lay the rope flat and pull both ends until the cord is straight, but not stretched. Run the tape from the inside of one handle to the inside of the other. A tape run around a curve adds several centimetres, and a cord measured with the handles included reads long by the length of both grips.

Rope Types, and Where the Rule Changes

The length rule holds for every type, and the type decides how the rope behaves once it is the right length. Five types cover most of the market.

The speed rope is a thin vinyl cord or a wire, built for double unders and fast singles. It is an indoor rope: on concrete or rough ground the cord wears quickly.

The licorice rope is a vinyl or PVC cord without a coating, and it is the freestyle standard. It is flexible enough to keep a shape through crossovers, which a stiff speed cord will not do.

The beaded rope is a cord threaded with beads. The beads strike the floor and make an audible click, which is why the type is used in rhythmic skipping and in double dutch freestyle. The sound is a timing cue, not a decoration.

The leather rope is thicker and less prone to tangling, and it wears more slowly outdoors. It is heavier in the hand, which suits long steady sets more than speed work.

The long rope is not a personal rope at all. Two people turn it while one or more others jump. Its length is set by the gap between the turners, and not by one jumper’s height.

TypeCordBest surfaceWhere it fits
SpeedThin vinyl or wireIndoor, smoothDouble unders, fast singles
LicoriceUncoated vinyl or PVCIndoor or smooth outdoorFreestyle and crossovers
BeadedCord with beadsAny hard floorRhythmic skipping, double dutch
LeatherThick leather cordOutdoorLong sets, less tangling
Long ropeAny of the above, longerGym or yardGroup and school use

Cutting, Knotting and the Handle Allowance

An adjustable rope solves the sizing problem by moving the cord inside the handle. A fixed rope solves it with a knot or a cut, and both approaches change the effective length by more than people expect.

The handle is not a small detail. One maker lists a 6 inch handle on its standard rope. Its lighter model uses 6.75 inches. That three quarter inch changes where the cord exits, and so how the rope swings.

Some ranges are sold in handle sizes, not millimetres. One maker lists S, M, L and XL as the sizing step on a fixed model. For a buyer, that means the size ladder on the order is a handle ladder, not a cord ladder.

If you cut, cut once and cut long. Shorten the cord by two centimetres, jump for a minute, then shorten again if it still feels long. A knot takes up length too. A knot in a vinyl cord also creates a stiff point, and that point clicks on the floor with every turn.

If the rope is adjustable, the setting has a limit at each end. Pulled fully in, the cord can foul the handle cap. Pulled fully out, the cord can slip under load unless the clamp is a screw type, and not a friction fit.

Six Lines for a Jump Rope Order

A rope order that can be checked is written in six lines. Each line is a length, a material or a named part. Each one is a place where two suppliers can quote the same price for a different product.

The cord length, and how it is measured. Between the handles, under slight tension. A figure with no measuring point named can mean the total length including handles, which is a different number by twelve to fourteen centimetres.

The cord material and diameter. Coated wire, vinyl, PVC or leather, with a diameter in millimetres. Diameter decides how fast the rope turns and how it feels in the hand.

The handle length and grip. In inches or millimetres, with the grip material named. A 6 inch and a 6.75 inch handle take the same cord and produce two different ropes.

The bearing type. Sealed ball bearing, bushing or plain bore. This is the part that decides whether the rope turns freely after a thousand turns or starts to drag.

The adjustment method. Fixed, screw clamp or friction fit, with the usable range stated. A friction fit that slips under load is the most common complaint on an adjustable rope.

The length range on the packing. What the box says, and whether a chart is printed on it. A rope sold in one length with a chart costs nothing extra and removes most returns.

Spec lineWhy it mattersHow to check it
Cord length and measuring pointDecides if the rope fits at allMeasure a sample, handles attached
Material and diameterSpeed and hand feelCaliper on the cord, name on the sheet
Handle length and gripWhere the cord exitsMeasure both models side by side
Bearing typeFree turning after many turnsSpin test, then spin again after a set
Adjustment methodWhether the setting holdsLoad the rope, pull, watch the clamp
Packing and chartReturns and support loadCheck the printed insert

Written down, those six lines become a cord spec a rope factory can quote on, and two quotes cover the same product. The bearing and clamp lines become the script for the pull test on a handle batch.

Hardware on a rope rewards the same thinking as any small metal part. That is why the gate and shape guide to carabiners covers load paths in the same way. A rope handle is not a life safety item, but the bearing and the clamp fail in the same order.

If a batch arrives with the wrong cord length or a clamp that slips, the remedy has its own rules. Then how a short rope batch is settled follows the sheet, not the argument.

The rope types and their uses are described in the reference entry on skipping ropes. The three-tier length rule, with its chest, waist and hip landmarks, is published in one supplier’s sizing guide. The upper limit appears on a second supplier’s page.

Panel of six jump rope specification lines including cord length and measuring point, material, handle length and bearing type
Six lines, and the one that decides whether the rope fits at all.

Questions Buyers Ask About Jump Rope Size

What size jump rope do I need for my height?

Add three feet to your height for a beginner rope, two feet for intermediate and one foot for speed work. At 170 cm that gives about 261, 231 and 200 cm of cord between the handles.

How do I know if my rope is too long?

Stand on the middle and pull the handles level. If they sit above your lower chest, the rope is long for a beginner. If the cord lands well in front of your toes on a slow turn, it is long for anyone.

Is the length measured with the handles?

No. The figure that matters is the cord between the handles. A 261 cm rope with 13 cm handles is about 274 cm end to end, and suppliers quote both numbers without saying which one they mean.

What length should I use for double unders?

Shorter than a beginner rope. The advanced rule of height plus one foot is the usual starting point, and the handle position check should put the handles near hip height.

Beaded rope or speed rope?

Beaded for rhythm and group work, because the beads click on the floor and give a timing cue. Speed for double unders, because a thin cord turns faster and cuts less air.

Can I cut a jump rope shorter?

Yes, on most cords, and it is the normal way to size a fixed rope. Cut two centimetres at a time, because a knot takes up length as well and cannot be undone.

The Short Version

Size the cord, not the rope. Measure between the handles, and use height plus three feet for learning, two feet for steady jumping and one foot for speed.

Confirm it with the handle position at chest, waist or hips. Then decide the type, because a beaded rope, a speed rope and a leather rope of the same length behave like three different products. Last, check the cord on the floor, because a chart guesses and a tape does not.

CORD, NOT TOTAL

One Length Fits Nobody

Selling a rope in one length means a chart and a measuring point, or a returns problem. Send the page you are quoting and the height range you sell to. We will tell you which two figures belong on the packing.

Send the Brief

Questions & Comments

We read every one and reply within 24 hours

Selling one rope length and wondering why the returns are high? Tell us the height range in a comment and we will work out the two packing figures that cut it.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x