Types of Carabiner: Shapes, Gates and Strength Ratings
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Types of Carabiner: Shapes, Gates and the Load That Decides

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 2, 2026 · 10 min read

A carabiner looks like a clip. It is really a load path with one weak point, and the weak point is a gate. Every type you read about is a choice about where the load travels and how that gate closes.

So this page is about two things. The shape that carries the pull, and the gate that holds it shut. After that, the three numbers printed on the side, and the standards that produced them.

Warm beige studio still life of an aluminium carabiner with a screw gate beside a small load test weight and a folded inspection sheet
Shape carries the load. The gate decides whether it holds.

Four Shapes, and Where the Load Travels

The trade counts four shapes, and the difference between them is not cosmetic. It is which side of the metal the load sits on.

The oval is symmetric. It is the oldest shape and the easiest to load from either end. That is why it still appears where a pulley or two ropes share the clip.

The D puts the straight spine on one side and the gate on the other, so most of the pull runs down the spine. That is why a D holds more load than an oval of the same weight.

The offset D shifts the gate slightly to widen the opening, and it became the standard shape in the 1950s. It is the shape most people picture when they say carabiner.

The pear or HMS is wider at the head, which leaves room for a friction hitch or a belay device to sit and turn. The extra width costs strength and weight, and it buys a wider basket.

ShapeLoad pathWhere it earns its place
OvalEven on both sidesPulleys and shared rope paths
DDown the spineGeneral load carrying
Offset DSpine, with a wider gateThe common all-round clip
Pear / HMSSpine, with a wide basketBelay devices and hitches

The Gate Is Where the Strength Goes

A non-locking carabiner has a sprung gate that swings open and snaps shut. It is fast, and it can open by accident when a rope or a sling runs across it.

A wire gate is a loop of wire instead of a solid bar. It is lighter, it does not freeze shut as easily, and it was patented in 1969 for maritime use before climbers adopted it in 1996.

A locking carabiner adds a sleeve over the gate. The sleeve is turned by hand or by a spring, and it stops the gate from opening until someone means it to.

The screw gate is the simplest lock and the slowest. A twist lock turns a collar a fraction. A triple action lock and a spring gate need two or three separate movements. They are chosen where an accidental opening is the main risk.

The keylock nose was developed between 1984 and 1987, and it exists for a small reason with a large effect. A smooth nose does not snag on webbing, slings or bolt hangers when the clip is loaded and unloaded in a hurry.

Panel comparing non-locking, wire gate, screw gate and triple action gate carabiners and the movements each needs to open
Four gate types, and the number of movements needed to open each one.

Three Numbers, and the One Buyers Skip

Every rated carabiner carries three figures on its side. The first is the long axis, with the gate closed and the load running spine to spine. The second is the short or minor axis, where the load runs across the clip.

The third is the open gate figure, and it is the one that gets ignored. It is measured with the gate held open, which is exactly the state a clip is in during the moment a rope runs through it.

The gap between the first and third figure is large. A clip that holds 20 kN closed can fall to 7 kN open, which is a drop of more than half. A buyer who quotes only one number has quoted the gate-shut case.

The minor axis figure is the smallest of the three, and it is small on purpose. A clip loaded across its width has almost no metal in line with the pull. The number then drops to roughly a third of the long axis figure. Cross loading is the failure a marking cannot prevent and a wide basket can.

The unit is the kilonewton, and the conversion is worth carrying in the head. One kilonewton is about 102 kg of force, so a 20 kN clip holds roughly two tonnes before it breaks. Breaking strength is not a working load, and no carabiner should ever be used near that figure.

StandardLong axis, closedShort axisOpen gate
EN 12275 / EN 36220 kN7 kNNot the headline figure
ASTM F1956, light use27 kN7 kN—
ASTM F1956, technical rescue27 kN7 kN7 kN
ASTM F1956, general rescue40 kN11 kN11 kN
ASTM F1956, heavy duty40 kN10.68 kN—

Two standards families sit behind those rows. In Europe, a connector used for access and industrial work falls under EN 362. Its gate-closed figure is nominally the same as EN 12275, at around 20 kN. Many connectors are certified to both.

In the United States, rescue carabiners are addressed by ASTM F1956, and the class decides the number. A technical rescue clip has to reach 27 kN closed, 7 kN open and 7 kN on the minor axis. A general rescue clip doubles the target to 40 kN closed and 11 kN open.

Which Type for Which Job

The use case decides the standard, and the standard decides the number. That order matters, because a stronger clip that misses the required standard is still the wrong clip for the job.

Recreational climbing. Non-locking clips carry the rope and the rack, and locking clips anchor. The euro figure of 20 kN closed is the usual floor, and the open gate figure is what protects a falling climber.

Industrial access. Work at height in Europe falls under EN 362, and the clip is part of a system with a harness, a lanyard and an anchor. The carabiner is the cheapest part of that system and the easiest to substitute, which is why the certificate matters more than the price.

Rescue. ASTM F1956 sets the classes, and a rescue clip usually carries a wider gate and a larger basket so that a glove can work it. A 7 kN open gate figure is a different product from a 20 kN closed figure on a light clip.

Everything else. The same hardware turns up in places with their own numbers. Hot air balloon carabiners are rated at 2.5, 3 or 4 tonnes. A screw-gate clip on a diver’s umbilical commonly carries a safe working load of 5 kN, which is about 500 kg.

Those last two examples are useful for a buyer, because they show the range. The same word covers a 500 kg working load and a 4 tonne balloon fitting. Only the standard on the certificate tells you which one is in the box.

Aluminium, Steel and the Weight Trade

Almost every clip sold for climbing is aluminium. The first aluminium carabiners went to the military in 1941, and they were the first commercial clips designed for that job.

Strength followed slowly. A 22 kN aluminium carabiner arrived in 1968, and steel clips had passed that figure long before. Steel is stronger for the same size, and it is heavier by a wide margin.

That trade explains where each metal appears. A rack of twenty aluminium clips is carried all day, so grams matter more than a figure nobody will approach. A fitting on a balloon or a permanent anchor stays put, so weight stops mattering and a rating in tonnes becomes reasonable.

Aluminium has one behaviour worth writing into an order. It does not spring back the way steel does, so a clip that has taken a hard load is retired and not straightened. A named alloy and a temper state on the drawing are how that argument starts from a document.

What a Batch Inspection Should Look At

A carabiner is a small part with a short list of failure points, and each one can be checked on a sample without a laboratory.

The gate spring. Open and close the gate twenty times. It should return with the same snap on the last movement as the first, and it should not rattle when the clip is shaken.

The nose. Run a thumb along the join between gate and body. A keylock nose sits flush; a plain nose has a step that catches on webbing, and that step is where slings wear through.

The marking. The body should carry the strength figures, the standard and a batch trace. A rated clip with no stamp cannot be matched to the certificate that came with the shipment.

The sleeve. On a locking clip, turn the sleeve through its full travel and check that it cannot be walked back by shaking. A sleeve that drifts open under vibration is the failure a lock exists to prevent.

Six Lines for a Carabiner Order

A carabiner order that can be checked is written in six lines. Each line is a figure, a named process or a standard, and none of them can be settled by looking at a photo.

The standard, by number. EN 12275, EN 362 or ASTM F1956, with the class. The standard decides the breaking strength, so it belongs above everything else.

Three strengths, not one. Long axis closed, minor axis, and open gate, each in kN. A quote with a single figure has quoted a marketing number.

The alloy and the heat treatment. Aluminium was first sold to the military in 1941, and the alloys used now are not interchangeable. A named alloy plus a temper state is a checkable line.

The gate type and the nose. Wire, solid, screw, twist or triple action, plus keylock or plain. The nose shape decides whether the clip snags on webbing under load.

Weight and gate opening. In grams and millimetres. Gate opening is the figure that decides whether the clip fits over a bolt hanger with a glove on.

The proof test and the marking. Every unit tested or sampled by batch, and what is stamped on the body. A rated clip with no marking cannot be traced to a certificate.

Spec lineWhy it mattersHow to check it
Standard and classSets the required strengthRead the certificate, not the page
Three strengthsShows the real weak pointLong, minor and open, each in kN
Alloy and temperStrength without brittlenessNamed grade on the drawing
Gate and noseHow it opens, whether it snagsSample in hand, spring it
Weight, gate openingFit and hand feelScale and caliper on a sample
Test and markingTraceability after deliveryBatch report plus the stamp

With those six lines written down, you have a drawing a carabiner factory can quote on, and two quotes cover the same product. The same lines become the script for the proof load on a finished batch.

The alloy choice inside those lines is the same trade-off that runs through every metal order, where a harder metal can be the wrong answer. A clip and a blade fail in opposite directions: one deforms and holds, the other chips.

If the batch arrives below the stated strengths, the remedy has its own rules. In that case how a short batch is settled follows the certificate, not the conversation.

The strength figures and standard numbers here are taken from the reference entry on carabiners, which cites the standards text. A plainer account of the same shapes is at this explainer of carabiner types.

Panel of six carabiner specification lines including long axis, minor axis and open gate strength figures
Six lines, and the three strengths that matter.

Questions Buyers Ask About Carabiner Types

What are the main types of carabiner?

Four shapes, oval, D, offset D and pear, and two gate families, non-locking and locking. The gate family decides how the clip opens, and the shape decides where the load travels.

What is the difference between locking and non-locking?

A locking clip has a sleeve or a second action over the gate. It cannot open by accident when a rope runs across it, and it costs time to work with one hand.

What do the kN numbers mean?

Kilonewtons of force. One kilonewton is about 102 kg, so a 20 kN clip holds about two tonnes before it breaks. That is a breaking strength, never a working load.

Should I buy oval or D shape?

An oval shares the load evenly and suits pulleys. A D sends the pull down the spine, so it holds more for the same weight. Most general use goes to the offset D.

Why does the open gate rating matter?

Because a clip is open for the moment a rope passes through it. A 20 kN closed clip can be rated 7 kN open, which is less than half. Only the closed figure is printed large.

Is EN 12275 the same as EN 362?

They are close on strength and different in scope. EN 12275 covers climbing connectors, and EN 362 covers industrial fall protection. A clip certified to both is normal.

The Short Version

Shape decides where the load travels. The gate decides whether it holds. The strongest clip in the box is the one that matches the standard for the job it will do.

Ask for three strengths, not one. Ask which standard the certificate names. Then check that the marking on the body ties back to that certificate.

THREE STRENGTHS

One kN Figure Is Not a Rating

A quote that names a single breaking strength hides the open gate figure, which is where a clip fails. Send the page and the standard you need. We will tell you which three numbers to ask for before a sample is pressed.

Send the Brief

Questions & Comments

We read every one and reply within 24 hours

A carabiner quote that names one breaking strength and stops there? Post the long axis, the minor axis and the open gate figures in a comment and we will tell you what is missing.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x