Down Fill Power: Two Tests, Two Numbers, One Comparison
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Down Fill Power: What the Number Measures, and What It Leaves Out

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 2, 2026 · 11 min read

Fill power measures how much space one gram of down fills. It says how good the down is, not how much is in the jacket. Two products need two numbers, and the test behind the first one exists in two versions that do not agree.

A 900 fill jacket with 60 g of down and a 600 fill jacket with 90 g can trap about the same heat. The first one is lighter and packs smaller. The second one costs less.

That comparison is the whole subject in one line. A listing that prints only the fill power has told you half of what you need.

There is a second problem underneath it. The number itself comes from a laboratory test, and there are two versions of that test in commercial use. They use different sample masses.

Warm beige studio still life of a glass measuring cylinder, a small pile of white down clusters, a laboratory balance and a folded test report
A cylinder, a weight and 30 grams of down. The number comes from that.

What the Test Actually Does

Fill power is a specific volume, which is the space one unit of mass occupies. In practice it is reported as cubic inches per ounce, and in metric terms as cubic centimetres per gram.

The test places a weighed sample of down in a cylinder and puts a weighted piston on it. After the piston settles, the volume under it is read. The volume divided by the mass is the fill power.

Ordinary feather sits near 300 cubic inches per ounce. The highest quality goose down reaches about 900. Most outdoor products sit between 500 and 900.

The larger the individual down clusters, the higher the number. Small clusters pack tighter, so a given weight traps less air and holds less heat.

Two Versions of the Test, Two Different Numbers

This is the part a buyer needs and a product page rarely prints. The same down can be tested under a US method and a European method, and the two do not use the same sample.

The US method published in 2013 specifies a cylinder of 288 mm diameter, a plate of 284 mm, a load of 94.25 g and a sample of 30 g. Conditioning is steam followed by heated drying.

The European method, published as BS EN 12130, uses a cylinder of 289 mm with a 1 mm tolerance. It also uses a mechanised compressing cylinder of 94.25 g and a sample of 20 g. Conditioning is a tumble dry plus two to five days in a screen box.

ItemUS method (2013)EN 12130
Sample mass30 g20 g
Cylinder diameter288 mm289 mm plus or minus 1 mm
Load94.25 g plate, 284 mm94.25 g mechanised cylinder
ConditioningSteam, then heated dryingTumble dry, then 2 to 5 days in a screen box
Result reported asCubic inches per 30 gFilling power, massic volume

A different sample mass and a different conditioning routine mean the two methods are not interchangeable. A number produced under one method cannot be compared line by line with a number produced under the other.

So when a supplier quotes 800 fill power, the useful follow-up question is which method produced it. A quote that cannot answer that question is a quote you cannot compare against a competitor’s.

Flat comparison of the US and European down fill power test methods showing sample mass, cylinder size, load and conditioning
30 grams against 20 grams, and two different conditioning routines.

Fill Power Is Quality, Fill Weight Is Quantity

Fill weight is the mass of down inside the product, in grams or ounces. It is a simple number and it is the one a factory can quietly reduce.

Multiply the two and you get a rough warmth figure. A 900 fill jacket with 2 ounces of down lands close to a 600 fill jacket with 3 ounces. That is how a comparison between two very different price points becomes possible.

The same arithmetic explains the loft rule. To reach the same loft, a product using 550 fill down needs roughly 40 to 50 percent more down by weight than one using 800 fill down.

For a buyer, this is the lever to watch. Raising fill power looks good on a hangtag and costs more per gram. Reducing fill weight saves money on every unit and is invisible on the pack.

A listing that prints 900 fill and no fill weight has told you the expensive half of the story and hidden the cheap half. That pattern is common enough that a missing fill weight is itself a signal.

The Number Bands and the Scarcity Behind Them

For sleeping bags, the published bands run like this: 600 to 650 is good quality, 700 to 750 is very good, and 800 to 950 or higher is excellent. Down between 300 and 500 is described as poor quality.

The high end of the range is scarce for a reason that has nothing to do with marketing. Down above about 700 comes from mature breeding birds that moult naturally. It is collected by hand, and not as a by-product of meat production.

Almost all commercial down is a by-product of geese raised for food, and those birds are young, so their clusters are smaller. Mature hand-collected down is rare and costs accordingly.

That scarcity is the honest justification for a high price. A product claiming 900 fill at a low price is claiming access to a material that is hard to get.

Panel showing down fill power bands from 300 to 950 with quality notes and the scarcity of the high end
Quality per gram. Without fill weight, the number shows only the expensive half.

Baffles Decide Whether the Number Can Be Delivered

Down behaves like a loose powder. Without compartments it slides to the lowest point and leaves the shoulders empty, so the shell is divided into baffles.

Sewn-through baffles are the cheapest. The stitching passes through both layers, which creates a line with no insulation along it and a cold spot.

Box baffles add a wall between the layers, so the chamber keeps its depth and the cold line disappears. Welded or heat-seamed baffles remove the stitch holes entirely, which also blocks wind.

A chamber also has to be big enough for the down to expand. A bag rated at 900 fill in a chamber sized for 600 fill cannot loft properly. The extra money then buys a number, not warmth.

Baffle typeCold lineWindCost
Sewn-throughYes, at every stitch linePasses through the seamsLowest
BoxNo, the chamber keeps depthPasses through the seamsMiddle
Welded or heat-seamedNoNo stitch holesHighest

This is where a high fill number and a cheap construction meet badly. Good down in a sewn-through shell still produces cold lines, and the customer will blame the fill.

Flat cross section diagram comparing sewn-through, box and welded baffles and marking where the cold line forms
The fill number cannot fix a seam that has no insulation across it.

Goose or Duck, and the Standard Behind the Claim

Goose down is the default and duck down is used to hold cost down. In hands-on testing the difference between the two is described as small, and the highest grades tend to be goose or Muscovy duck.

Species matters less than cluster size, which is what the fill number already reflects. A high number in duck down beats a low number in goose down for warmth per gram.

The claim that does need paperwork is animal welfare. The Responsible Down Standard is a voluntary scheme covering how the birds are treated, and products carrying it are marked as RDS approved.

If a pack claims responsible sourcing, ask for the certificate and the certificate number. If the claim carries no paperwork, it is a phrase, not a standard.

Down or Synthetic, Written as an Order

Synthetic insulation changes the whole conversation, because it has no fill power figure. It is specified by weight per area and by thickness, which is easier to check and harder to market.

Three things follow for a buyer. Synthetic costs less per unit of warmth and it keeps working when damp. It behaves the same from lot to lot, so a repeat order arrives like the last one.

The trade is weight and life. Synthetic is bulkier for the same warmth and it loses loft faster across washes. That is why it suits car camping better than backpacking.

Down wins on warmth per gram and on pack size. It brings two risks that synthetic does not: a fill power quote that cannot be compared across methods, and a material that varies by lot.

For a specification, that difference decides which numbers you write down. A down order needs fill power, method and fill weight. A synthetic order needs grams per square metre, thickness and the number of layers.

Choosing between them is a channel question before it is a technical one. A product sold on pack size needs down. A product sold on price and on a damp weekend needs synthetic, and pretending otherwise adds cost the customer will not pay for.

How to Check the Number on an Order

Fill power is measured on loose down, not on a finished jacket. That single fact decides how verification has to work, because there is nothing in the product to test.

Ask for the down lot report. The mill or the down factory tests the lot, and the report belongs to that lot. Ask which method was used, and match the lot number to the delivery.

Weigh the fill. A fill weight declaration per size is the cheapest control available, and it is the number that gets reduced when a price is squeezed. A weighing test on a cut sample settles it.

Measure the loft. Shake a finished piece out, let it rest, then measure chamber height with a ruler against the sheet. It is crude, it is not a substitute for the lab, and it catches a flat product before it ships.

Watch the shipping. Down stored compressed loses loft over time, and the same is true in transit. A long sea leg in a compression sack is a real risk, and it is why the packing instruction belongs in the sheet.

The good news is that loft comes back. Washing gently and drying with care opens the clusters again, so a flattened sample is not automatically a failed one.

CheckWhat it provesWhat it cannot prove
Down lot reportThe fill power and method for that lotThat this lot went into these units
Fill weight per sizeHow much down is in the productHow good that down is
Loft measurementThe product lofts as builtThe fill power of the down inside
Packing instructionLoft is protected in transitAnything about the fill itself

Five Lines for the Fill Specification

A down order that can be checked has five things in writing. Each one closes a gap that leaves room for a quiet substitution.

Fill power, method and tolerance. The figure, the test method it was produced under, and how far below it a delivered lot may sit. Without the method, two quotes are not comparable.

Fill weight per size. Grams per size and per baffle zone if the zones differ. This is the line that stops a high fill number arriving with half the down.

Species and cluster content. Goose or duck, and the down-to-feather ratio. A fill number can be met with a lot that carries more small feather than expected.

Baffle construction. Sewn-through, box or welded, with chamber depth. The fill cannot perform in a chamber built for a lower grade.

The claim and its certificate. Any RDS or responsible-sourcing statement quoted in the sheet, with the certificate number.

Once those five are written, a fill sheet a lab can work from exists, and the argument moves to measurement. A finished-goods check then has a fill weight to weigh and a loft to measure.

On a repeat programme, the mid-run visit is where a fill change shows. Down is bought by the lot, and a cheaper lot is often swapped in halfway.

If a lot does arrive light, the remedy follows the sheet. What a short fill is worth is decided by the declared weight, not by an argument after delivery.

Questions Buyers Ask About Down Fill Power

Is higher fill power always warmer?

No. It is warmer per gram. A low fill power product with more down can be warmer than a high fill power product with very little.

Why do two suppliers quote different numbers for the same down?

Different test methods. The US method uses a 30 g sample and steam conditioning, and the European method uses 20 g and a different conditioning routine.

What is a good fill power for a jacket?

Between 600 and 750 covers most outdoor products. Above 800 buys weight and pack size rather than warmth on its own.

Does fill power apply to the finished jacket?

No. It is a property of the loose down. The product’s warmth also depends on fill weight, baffle design and chamber depth.

What does RDS mean on a down product?

The Responsible Down Standard, a voluntary scheme for animal welfare in the down supply chain. It only means something with a certificate number behind it.

Can a flattened jacket be restored?

Usually yes. Gentle washing and careful drying opens the clusters again. Storing down compressed for months is what causes the loss.

The Short Version

Fill power is the quality of the down and fill weight is the quantity. Buy on the pair, and ask which test method produced the first number.

Then check the parts the number cannot reach: the baffle that carries the warmth, and the declared weight that a squeezed price quietly reduces.

FILL POWER AND SET

Two Numbers, One Real Comparison

Two down quotations, two impressive fill numbers, and no fill weight on either? Send both sheets and the down lot report. We will say which test method produced each figure and where the fill weight sits before you cut a sample.

Send the Brief

Questions & Comments

We read every one and reply within 24 hours

Two down quotations with two impressive fill numbers and no fill weight on either? Send both sheets and the down lot report, and we will say which test method produced each figure.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x