WiFi 6 vs WiFi 5: What the Box Number Hides
Wi-Fi 6 is not three times faster than Wi-Fi 5. The standard’s own rate rises 37 percent.
Every electronics shop sells the same story. Wi-Fi 5 tops out at 3.5 Gbps, Wi-Fi 6 reaches 9.6, so the newer one must be nearly three times quicker.
That comparison is real, and it is the least useful number on the page. The rate a standard quotes grew 37 percent between generations. What grew fourfold is throughput in a crowded room.
This page separates the two claims. It explains the mechanisms behind the second one without maths. Then it shows how to read a label like AX3000.
The Short Answer
Wi-Fi 5 is the standard named 802.11ac. It works in the 5 GHz band only, and falls back to the older 802.11n rules when a device uses 2.4 GHz.
Wi-Fi 6 is 802.11ax. It works in both 2.4 and 5 GHz, so the whole radio obeys one set of rules. The 6 GHz version is called Wi-Fi 6E.
The practical difference is not peak speed. It is what happens when twelve devices want to talk at once. Wi-Fi 6 gives the access point a way to serve several of them in one turn.
Old phones still connect. They simply do not get the new scheduling, which is the part buyers forget to model.
What the Two Labels Actually Mean
The names come from the Wi-Fi Alliance, not from the IEEE. The IEEE numbers amendments to 802.11; the Alliance sells them under round numbers.
The Alliance’s own feature list is short and worth reading once. It names six additions and never mentions a speed figure.
Wi-Fi 5 was introduced in 2014 by the Alliance’s account. Wi-Fi 6 arrived in 2018 as a certification programme, and the IEEE approved the finished amendment on 1 September 2020.
That gap explains a lot of bad product pages. A router sold as Wi-Fi 6 in 2019 was certified against a draft. It may lack features the final text added.
One more date matters for spare parts. A model released in 2019 and one released in 2024 can both say Wi-Fi 6 and behave differently.
The bands are not equal either. The 2.4 GHz band holds less than 100 MHz of spectrum. The 5 GHz band has a little over 700 MHz. The 6 GHz band has about 1,200 MHz.
That last figure is why 6E exists. Wide channels need room, and the 6 GHz band has the most of it.
The Number on the Box Is Not the Gain
The 9.6 Gbps figure is a ceiling built from every best case stacked together: the widest channel, the highest modulation, the most streams.
Compare the two ceilings and you get roughly 2.7 times. Compare the rate each standard quotes per stream and you get 37 percent. Compare throughput in a busy room and the published figure is at least four times.
| What is being compared | Wi-Fi 5 | Wi-Fi 6 | Gap |
|---|---|---|---|
| Rate range in the standard | 6.5–6,933 Mbit/s | 0.4–9,608 Mbit/s | The famous 9.6 |
| Quoted rate per generation | Baseline | +37 % | The honest one |
| Throughput in a crowded room | Baseline | At least 4× | The useful one |
| Latency, as reported | Baseline | Down 75 % | The one users feel |
Those last three rows are not our measurements. They are the figures published with the standard’s own summary, and they describe dense settings, not an empty room.
So the buying question changes. Not “how fast is this router”, but “how many devices will share this room, and does my gear support the scheduling that fixes it”.
1024-QAM: 25 Percent in One Line
Modulation is how many bits ride on one wave. Wi-Fi 5 tops out at 256 states per symbol. Wi-Fi 6 tops out at 1,024.
Four times the states sounds like four times the data. It is not, because a denser signal needs stronger coding to survive noise. The standard answers with two steps up the table.
The cleanest way to see the gain is to compare the last row of each generation. Both use the same channel, the same guard interval and one stream, so nothing else is in play.
| Top step | Modulation | 20 MHz | 160 MHz |
|---|---|---|---|
| Wi-Fi 5, MCS 9 | 256-QAM | 114.7 Mbit/s | 961 Mbit/s |
| Wi-Fi 6, MCS 11 | 1024-QAM | 143.4 Mbit/s | 1,201 Mbit/s |
| Gain | Four times the states | +25.0 % | +25.0 % |
Twenty five percent, on a clean signal, at close range. That is a real gain and it is not the reason to upgrade.
It is also the number a datasheet will not show you. The sheet quotes the ceiling, where modulation is one of four multipliers.
OFDMA: Splitting by Frequency
Older Wi-Fi handed the whole channel to one device per turn. Everyone else waited, even if that device was sending a tiny status message.
OFDMA changes the unit of the turn. The access point cuts the channel into resource units and assigns them to several devices at once.
The sizes are fixed in the standard: 26, 52, 106, 242, 484 or 996 tones. A tone is one subcarrier of 78.125 kHz, so the smallest slice is about 2 MHz wide and the largest near 80 MHz.
To make room, Wi-Fi 6 uses four times as many subcarriers as Wi-Fi 5 in the same width. At 20 MHz that is 256 instead of 64.
More subcarriers means each is narrower, so each symbol lasts four times as long: 12.8 microseconds against 3.2. A longer symbol is harder to break with an echo, which is why outdoor links liked this change.
The trade is latency per symbol. The gain is that a video call and eight sensors no longer take turns for the whole channel.
MU-MIMO: Splitting by Space
The second mechanism splits in a different dimension. Instead of dividing frequencies, it divides directions, using several antennas to aim separate streams at separate devices.
Here is where most comparison pages go wrong. Wi-Fi 5 already had multi-user MIMO, in the downlink direction. It was not a one-device-at-a-time standard.
Wi-Fi 6 adds the uplink. The access point sends a trigger frame that lists which device gets which resource unit and which coding to use. Devices then answer together instead of queueing.
| Direction | Wi-Fi 5 | Wi-Fi 6 | What it fixes |
|---|---|---|---|
| Downlink to several devices | Yes | Yes | Streaming to many screens |
| Uplink from several devices | No | Yes, on a trigger | Cameras and sensors replying |
| Frequency split and space split together | No | Yes | A mixed room of big and small traffic |
| Neighbouring network ignored sooner | No | Yes, by colour mark | Flats with six networks in range |
That third row is the one to hold on to. OFDMA and MU-MIMO can run in the same transmission. One device gets a small slice, another gets a separate beam, and both finish in the same turn.
For a buyer the check is simple. Ask how many streams the access point has in each band, and whether the client radios support the uplink half.
Two Features Nobody Puts on the Box
Two additions change daily behaviour and never appear in the marketing line.
The first is target wake time. It lets the access point agree a schedule with each battery device, so a sensor sleeps between check-ins instead of listening all day.
The second is a colour mark on each frame. It tells a device whether a signal came from its own network or from the flat next door. With that mark it can start transmitting sooner.
Both matter in dense housing. Neither shows up in a Gbps figure, which is exactly why the figure is a poor way to choose.
Decoding a Label Like AX3000
Retail model names hide three numbers. Once you can pull them apart, two routers with the same badge stop looking equal.
The badge is the sum of the top rate in each band. Take a two-stream design in both bands, at the highest modulation, with a short guard interval.
On 2.4 GHz at 40 MHz, one stream reaches 286.8 Mbit/s, so two streams give about 574. On 5 GHz at 160 MHz, one stream reaches 1,201, so two streams give 2,402.
Add them and you get 2,976. Round up and the shop calls it AX3000. Nothing was measured; it is arithmetic on the the MCS table behind the label.
The same badge can be built another way. A design with four streams on 5 GHz at 80 MHz also lands near 3000. One of those two handles a crowd better than the other, and the badge cannot tell you which.
So ask for the stream count per band. Ask for the widest channel each band supports, and whether 160 MHz needs a radar check first.
What Your Older Devices Do Not Get
A Wi-Fi 6 access point will serve an older phone. It simply serves it under the older rules, one device per turn.
That is not a defect. It is how the scheduling works: a client that cannot read a trigger frame cannot join a shared uplink.
In a mixed room this decides the outcome. Six new devices and six old ones do not split the gain evenly. The old half keeps the queue that the new half was meant to remove.
Before you pay for the upgrade, count the clients. Then count how many of them support the newer rules. The second number is the one that predicts what you will feel.
When Wi-Fi 6 Will Not Help
Half the upgrade advice you will read never asks what the network carries. Start there and the answer often changes.
Take a shop with eight cameras. Each pushes about four megabits when it is busy, so the whole set needs roughly 32 Mbit/s. No Wi-Fi 5 access point breaks a sweat on that.
Take one laptop alone in a room. There is no crowd to schedule, so the sharing gain never appears. What is left is the 25 percent modulation step, and only at close range.
Take an office on a 200 Mbit/s line. The radio ceiling is four times the line. The line is the limit, and it will stay the limit.
Take a phone with two antennas. At the top of the table it reaches about 1,200 Mbit/s. Buying a four-antenna access point does not give that phone a third antenna.
And take the 2.4 GHz band. On Wi-Fi 5 hardware that band drops to the older 802.11n rules, so anything parked there gets neither generation’s newer tricks.
The honest rule is short. Buy Wi-Fi 6 when many devices share one room and the room is the bottleneck. Buy it for one device, and you are paying for a queue that never forms.
Six Lines for the Order
Put these on the enquiry and the quotes become comparable.
One. The band plan: which band carries the load, and whether 6 GHz is included.
Two. Streams per band, written as numbers, not as a combined badge.
Three. The widest channel each band supports, and how the unit behaves when radar is detected.
Four. The client mix you expect, and how many of those clients support the shared uplink.
Five. The radio approval you need for your market. A wireless product is not covered by a generic safety mark. The radio approval route for a wireless product is a separate file.
Six. Power and mounting if it is an access point. Ceiling units usually take their supply over the data cable. What powers an access point over one cable decides whether your switch can feed it.
Then attach the line list. The line items a factory must answer are what turn a catalogue page into a quote you can compare.
If the volumes are serious, check the line before you check the price. Auditing the line that builds it is cheaper before the tooling is cut.
Send me the datasheet or the shop listing for the unit you are looking at. I will pull out the stream count, the widest channel each band supports, and whether the badge is arithmetic or marketing. You get a short answer that tells you what to ask the supplier next.
Check The SpecQuestions Buyers Ask
Is Wi-Fi 6 faster than Wi-Fi 5?
At the top of the table, yes, by about 25 percent for the same channel and stream. In a crowded room the published gain in throughput is far larger, because several devices can be served in one turn.
Do I need new devices to benefit?
The access point alone gives you the frequency sharing. The uplink half only works when the clients can read a trigger frame, so a room of older phones keeps the old queue.
Does Wi-Fi 5 really only talk to one device at a time?
No. It has multi-user MIMO in the downlink direction. Many comparison pages still say otherwise. What Wi-Fi 6 adds is the uplink direction.
What does AX3000 actually mean?
It is the sum of the best rate in each band, under the highest modulation, with every stream counted. It is arithmetic on the standard’s rate table, not a measured speed.
Is 160 MHz worth asking for?
Only if the room is quiet. In the 5 GHz band a 160 MHz channel often needs a radar check before it starts, and in a busy building it is rarely free.
Will a Wi-Fi 6 router improve range?
Not much on its own. Range follows transmit power, antenna design and what the walls are made of. The newer standard helps capacity and latency far more than distance.
Questions & Comments
We read every one and reply within 24 hoursIf you have two router quotes in front of you and they look identical, send me both badges. The difference is almost always in the stream count.