What Is Qi Charging: Two Coils, One Conversation
Qi charging moves power across a gap, with no wires.
Two flat coils face each other. The pad pushes an alternating current through its coil, and the field that creates pushes a current through the coil in the phone.
The name comes from the Chinese word for vital energy. The standard comes from the Wireless Power Consortium, and it has been revised steadily since 2010.
Most pages stop at the coil. The useful parts are the two things nobody mentions: how the two ends talk, and what happens when they line up badly.
The Short Answer
Qi is a standard for inductive charging. A base station sends power. A mobile device receives it. Both parts are defined in the same document, so one brand of pad can charge another brand of phone.
Power moves through a magnetic field, not through metal contacts. Nothing on the pad touches a conductor in the phone.
The gap is small. A reference design puts the coils about 5 mm apart, and the specification allows separation up to about 40 mm.
The alternating current runs in the range of roughly 105 to 205 kHz. A reference transmitter coil has 20 turns on a 19 mm inner diameter and a 40 mm outer diameter. Its inductance is 24 µH plus or minus one.
Why the Coils Must Face Each Other
A transformer works because two coils share a magnetic path. Qi is a transformer with an air gap where the iron would be.
Remove the iron and the coupling weakens fast. Offset one coil by half its width and most of the field misses the other coil entirely.
That is why a phone charges on the centre of a pad and barely at all near the edge. The field is there, but the receiving coil is not in it.
Two arrangements exist to handle this. A guided design asks the user to place the device in one spot, marked by a shape. A free design uses a bundle of coils, or a coil that moves, so the field follows the device.
The free arrangement is convenient and more expensive. It also draws more standby power, because the pad has to keep looking for a device.
Coil size sets the limit on how much power can cross. A pad built for a phone carries a coil wide enough to cover the phone coil. A pad built for earbuds carries a smaller one, and the smaller the two coils, the less power moves for the same field strength.
Coil size sets the limit on how much power can cross. A pad built for a phone carries a coil wide enough to cover the phone coil. A pad built for earbuds carries a smaller one, and the smaller the two coils, the less power moves for the same field strength.
The Receiver Is the One Giving Orders
This is the part that surprises buyers, and it is the part almost no explainer covers. The two ends talk, but not with a radio.
The receiver changes the load on its own coil. That change shows up as a current change in the transmitter coil. The transmitter watches for those changes and reads them as data.
The technique is called backscatter modulation. The receiver speaks by drawing more or less power in a pattern, and the transmitter listens to its own current.
So the phone asks for what it needs. The pad adjusts. If the phone asks for more than the pad can give, the pad refuses, and the charge stays at the lower level.
One direction only. The phone can talk to the pad. The pad cannot send a message back except by cutting or reducing power.
That asymmetry explains a common user experience. A pad that flashes a light is signalling through colour, not through data, because it has no channel for words.
Fourteen Years of Wattage
The standard has been revised again and again. Each revision moved one of three things: the power ceiling, the foreign object check, or the way the two coils line up.
Reading the version history as a table is the fastest way to see where a product sits.
| Version | Year | Ceiling | What it added |
|---|---|---|---|
| 1.0 | 2010 | 5 W | The first specification, single or multiple coils |
| 1.1 | 2012 | 5 W | Foreign object detection arrives |
| 1.2 | 2015 | 15 W | Extended power profile, better thermal tests |
| 1.2.3 | 2017 | 30 W | A power class that can negotiate higher |
| 1.3 | 2021 | — | Rebuilt documents, authentication, tougher object tests |
| 2.0 | 2023 | 15 W | Magnetic profile, sold as Qi2 |
| 2.2 | 2025 | 25 W | A coil check before power, loss calibration above 15 W |
Three names sit inside those versions, and quotes use them without explanation. The baseline profile is the original 5 W mode. The extended profile is the 15 W mode. The magnetic profile is the new one, and it is the only one that requires magnets.
So “Qi 15 W” can mean two different things. It can be a pad on the extended profile, which asks the phone to line itself up. Or it can be a Qi2 pad, which holds the phone in place with magnets.
| Profile | Ceiling | How it lines up | What it suits |
|---|---|---|---|
| Baseline | 5 W | Free placement | Small devices, low-cost pads |
| Extended | 15 W | Free placement | Phones, when the user centres them |
| Magnetic | 15 W, 25 W later | Magnet ring | Phones that carry magnets |
Why Magnets Are the Real Change
Every efficiency problem in this article traces back to alignment, and the 2023 revision attacked it with hardware rather than software.
The magnetic profile puts a ring of magnets around the coil in both the pad and the phone. The two rings pull together, and the coils end up in the one position where coupling is strong.
The design is based on a phone maker’s own magnetic charger, and the specification makes it backwards compatible with those accessories.
That is why the same 15 W figure appears twice in the table with different meanings. The extended profile can reach 15 W when the coils happen to line up. The magnetic profile reaches it because they cannot fail to line up.
The market has responded unevenly. One large phone brand sells handsets described as ready for the standard but without magnets inside, which need a magnetic case to work. Another put the magnets in the phone itself in 2025.
For a buyer, that means the word on the box is not enough. The useful question is whether the magnets are in the device, in the case, or nowhere.
Where the Missing Power Goes
Nothing in this chain is lossless. The pad converts mains power to a high-frequency current. The coil radiates a field. The receiving coil turns part of that field back into current, and a rectifier makes it usable.
Each step keeps less than it receives. What is not delivered ends up as heat in the coils, in the shielding behind them, and in the electronics on both sides.
Heat is not just waste. It is a limit. A battery that warms up takes charge more slowly. So a pad that runs hot can deliver less over an hour than a cooler pad of the same rating.
This is why a 15 W pad and a 15 W pad are not the same thing to buy. The one that keeps its coils cool holds the higher rate for longer.
Two physical choices drive that. A thicker shield behind the coil keeps the field out of the phone’s own metal. A bigger coil spreads the same loss over more area.
Neither is visible in a photo. Both show up as grams and as millimetres of thickness.
A thick case makes both worse. It adds distance the field has to cross. More current is needed for the same delivered power, and more of it ends as heat on both sides.
Charging overnight hides that problem. Charging for twenty minutes in a car, with the screen on, does not.
What a Pad Cannot Do
Four limits come up in every support conversation, and none of them is a fault.
It cannot charge through metal. A metal plate, a coin, or a card with a chip inside sits in the field and heats up instead of passing power.
It cannot charge a device with no receiver. The phone needs its own coil. A case adds one only if the case was built for it.
It cannot ignore distance. The specification allows a gap up to about 40 mm, but every extra millimetre costs coupling and turns into heat.
A pad fixed under a table also has less air around it, so it has to shed its own heat with less help.
It cannot work through a desk. Pads sold for fixing under a tabletop eat that thickness out of the same 40 mm gap. The desk has to be thin, and the pad has to be built for the job.
It cannot promise the rate on the box. The rate depends on the phone, the temperature, and how well the two coils sit.
That last point explains a common complaint. A 15 W pad can charge a phone slowly in summer. The pad did not break. The phone reduced its own rate as the battery warmed.
The Coin on the Pad
Put a key on a charging pad and the field will heat it. That is not a fault in the pad. It is what a changing magnetic field does to metal.
Every standard version since 2012 has dealt with this problem, and the way it is handled has changed more than once.
The basic method is a power balance. The pad knows how much it is sending. The phone reports how much it is receiving. When the gap is larger than the expected loss, something else is absorbing power, so the pad stops.
The weak point is a small object with poor coupling. It absorbs little power early on, so the balance looks fine, and it heats slowly.
The 2021 revision attacked that case with a test receiver of deliberately low quality factor. A pad now has to detect a badly coupled object before it can pass.
The 2025 revision moved the check earlier. The pad measures the quality factor of the coupled system before it transfers any power at all. It also calibrates the loss differently above 15 W.
So “supports foreign object detection” is not one claim. It is a claim that depends on the version, and a cheap pad can pass an old test while failing a new one.
Five Lines for the Order
A pad order that says “15 W Qi” leaves the version, the profile and the object test open. Five lines close them, and they fit the same sheet you send a supplier for any other part.
One. Name the version and the profile, not just the wattage.
Two. State the delivered watts at the phone, and the alignment condition they assume.
Three. Say where the magnets live: device, case, or none.
Four. Ask for the object detection version and the test that proves it.
Five. Require the case temperature at full load after half an hour, plus the derating curve behind it.
Approve a sample before the run. Put a phone on three units from the pilot lot and watch the charge rate for ten minutes. The number that holds is the number the order will deliver.
The rest of the product has its own file. A powered accessory still needs an insulation check before it ships, described in the insulation check explained here. If the pad also carries a wall adapter, the numbers on that adapter are a separate question, covered in the GaN charger guide.
For a product sold in Europe, the paperwork is separate again, and the CE file sets out what goes into it.
Send me the spec or the listing you were given. I will name the version and the profile behind the wattage, say where the magnets sit, and list what the object detection test still has to prove. No cost, no obligation.
Check My PadQuestions Buyers Ask
Is Qi the same thing as wireless charging?
No. Qi is one standard for it, and the most widely used one. A device can charge without wires and still not be Qi.
Will any Qi pad charge any phone?
Only if the phone has a compatible receiver inside or in a case. The standard defines both sides, so the brands can differ as long as both follow it.
Why does my phone get warm on a pad?
Two reasons. Some of the power is lost as heat in the coils and the shield. And the battery warms as it charges, which is normal for any method.
Is Qi2 faster than Qi?
Not by the ceiling. Both reach 15 W. Qi2 reaches it more often, because magnets keep the coils lined up. The 2025 revision adds a 25 W mode.
Do I need a magnetic case?
It depends on the phone. Some have magnets built in. Some are sold as ready for the standard but need a magnetic case to hold alignment.
Does a thick case stop the charge?
It can. The specification allows a coil gap up to about 40 mm, but the further apart the coils sit, the weaker the coupling and the more heat for the same power.
Questions & Comments
We read every one and reply within 24 hoursIf the listing says 15 W Qi and nothing else, send me the line. I will name the version, the profile and the object test behind it.