SMT Assembly: What the Process Is and What to Check
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

SMT Assembly: What the Process Is and What a Quote Must Show

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder, Sourcing Pioneer
· Updated October 26, 2026 · 10 min read

SMT assembly is the step where small parts are placed on a board and soldered in one pass through an oven. It is also the step where buyers lose money without noticing, because a finished board looks the same whether the process ran well or badly. The terms that fix what the shop owes you decide more of the outcome than the price does.

Studio still life on a flat cream surface showing a green printed circuit board with small surface mount parts, a stainless steel stencil sheet beside it, and a reel of components on the right, with a navy serif headline reading SMT ASSEMBLY and an amber subhead reading FIVE STEPS
Five steps, and every one of them leaves a number behind.

The Short Answer

SMT assembly is five steps in a fixed order. Print the paste, place the parts, melt the paste in an oven, inspect the joints, then test the board.

Each step leaves a setting behind. The setting is what separates a shop that controls its process from a shop that hopes.

So the useful question is not whether a factory can do SMT. Almost all of them can. The question is which numbers the shop records, and whether it will put them in the order.

Ask for five things in writing. The stencil thickness, the paste type, the oven profile, the inspection method, and what the test covers. A shop that answers all five is a shop you can hold to something.

What SMT Means, in Plain Words

SMT stands for surface mount technology. The name describes where the part sits: on the surface of the board, on small metal pads, held by solder.

The older method is through hole. Legs pass through the board and are soldered on the far side. Most boards today use both methods, and a board that mixes them is normal.

The difference that matters to a buyer is where the joint ends up. A through-hole joint is on the outside, so a person can look at it. An SMT joint sits under the part, so nobody can.

That one fact drives the rest of this article. You cannot judge the work by looking at the board. You judge it by the records the shop keeps while making it.

A second fact matters just as much. The parts are getting smaller while the boards stay the same size, so more of the joint is hidden every year. A process that passed a visual check in 2015 hides more now.

Five Steps, in One Direction

The line runs one way and does not go back. Paste, place, reflow, inspect, test. Each step can ruin the work of the step before it, and none can repair it.

Flat vector diagram on a cream background showing five rounded outlined boxes in a row labelled PRINT, PLACE, REFLOW, INSPECT and TEST, joined by arrows that run in one direction only, with a small note under the chain reading NO STEP CAN GO BACK
One direction only. A bad print is a bad board, and no later step fixes it.

Printing comes first. A stencil is a thin metal sheet with holes cut where the pads are. Paste is pushed through the holes onto the board.

Placement comes second. A machine lifts parts from reels and sets them on the wet paste, at speed, with a camera that checks each one landed.

Reflow comes third. The board travels through an oven with zones at rising heat. The paste melts, wets the pad and the pin, and sets as one piece of metal.

Inspection comes fourth. A camera compares every joint with a stored image, and an X-ray machine looks through the parts that cover their own pads.

Test comes last. The board is powered, and the test says whether the circuit works. It does not say how long it will work.

A board with parts on both sides goes through the first three steps twice. The second pass must not shake the first side loose, so the shop carries the board on a support through the oven. Ask whether it does.

StepThe number behind itWhat goes wrong
PrintStencil thickness, and the paste typeToo much paste joins two pads
PlacePlacement force, and the rotation checkA part turned the wrong way still looks placed
ReflowPeak heat, and time above meltingA joint that looks right and is not
InspectHow much is checked, and the class it is judged toA fault found on your customer’s bench
TestWhat the test covers, and what it skipsA board that powers on and fails in a month

The Print Decides More Than Any Other Step

Printing is the step to argue about, because everything after it inherits the result. Paste in the wrong place cannot be moved by a better machine downstream.

The stencil thickness sets how much paste lands on each pad. A thicker sheet puts down more paste, and more paste means bridges between pads that sit close together.

Paste is also a material with a clock. It has a shelf life, a stirring rule, and a working life on the stencil. A line that stops for an hour comes back to paste that no longer flows the same way.

Ask three questions and the answers tell you how the shop runs. What thickness is the stencil. How old is the paste in the tub. What happens to paste left on the sheet at a stop.

Then ask for a print check on the first board of the run. A shop that measures paste volume before placing parts is a shop that knows where its faults start.

The fourth question is the one most buyers never ask. Who cuts the stencil, and is it cut for this board revision. A stencil made for an older file puts paste where the new pads are not.

Placement: Fast, Blind, and Checked by a Camera

The placement machine is the part of the line that looks most impressive and decides the least. It is fast and it is accurate, and it still makes two mistakes that a camera cannot catch.

The first is rotation. A part placed at the wrong angle sits flat and looks right in the machine’s own check. Only the test finds it, and only if the test covers that part.

The second is the wrong part in the right place. A reel loaded with a similar value looks identical from above. Ask how the shop checks a reel against the file before it goes on the machine.

The answer you want is a scan of the reel label against the bill of materials. A person does it at the start of the run. A shop that loads from memory is a shop that will load from memory again.

One more setting belongs in the quote. How the board is arranged on the panel. The panel is the larger sheet the shop handles. The number of boards per panel decides how much of your money goes into rails and gaps.

Panel design is a shared job. The shop knows its machine, and you know how the board is used. A panel with too few boards raises the unit cost. A panel with too many boards can bow in the oven.

Reflow: The Oven Profile Is a Document

Reflow is where the paste becomes metal. The board passes through zones of rising heat, and the heat curve is called a profile.

The profile has three parts that matter. How fast the board warms, how long it sits at a middle heat, and how hot it gets at the peak.

The middle hold lets the paste settle and lets the flux do its work. Skip it and the paste can boil, which throws small balls of solder across the board.

The peak of the curve is where the paste turns liquid. Too cool and the joint is dull and weak. Too hot and parts take damage that shows up later.

Here is the question worth asking. Is the profile measured on this board, or copied from the last job.

A measured profile comes with a printout and a thermocouple attached to a real board. A copied profile is a guess with a temperature on it. The two boards may share an oven and share nothing else.

A second detail belongs on the same line. Parts that have sat in store absorb water, and water turns to steam in the oven. The steam lifts the part off its pads, and the fault appears as a weak joint weeks later.

Shops call the fix baking, and the need for it depends on how the part was packed and how long it sat. Ask whether the shop bakes parts from opened reels before a run. The answer is free, and it separates two kinds of shop.

Inspection: A Camera, an X-ray, and a Standard

Inspection is the step buyers trust most and understand least. A camera check is not a guarantee, and the standard behind it decides what passes.

The camera is called AOI, for automated optical inspection. It compares each joint with a picture stored from a board that was judged good. It finds missing parts, shifted parts and bridges.

It cannot see under a part. So a board with parts that hide their own pads also goes through X-ray, and the X-ray is the only way to judge those joints.

Ask two numbers about the camera. How many boards in the run are checked, and what share of its alarms turn out to be false.

The second number is the one that matters. A camera that calls a fault on every second board gets switched off by the operator, and a switched-off camera checks nothing. A shop that tracks false alarms is a shop that keeps its camera on.

The standard matters as much as the machine. Solder joints are judged against a written class, and the class decides how much solder is enough.

Ask which class the work is judged to, and ask to see the page. A shop that answers in general terms is telling you it has not agreed a limit with anyone.

What a visit can check on a line is a different question from what the camera checks. A visit sees the records, the reels and the oven printouts. It does not re-run the X-ray.

The Ten Lines a Quote Must Carry

A quote for SMT assembly is easy to write badly, because a single unit price hides everything that decides the outcome.

Ask for the lines separately. Ten of them turn a price into a specification you can compare with the next shop.

LineWhat it has to say
Board dataSize, layer count, thickness, finish, and the file revision
SidesOne side or two, and whether the second pass uses a carrier
Parts per boardThe count, and the smallest pitch on the board
Who buys partsYou supply them, or the shop does, with the brand and seller named
StencilThickness, who cuts it, and whether it is a new cut
PanelBoards per panel, rail width, and who designs it
InspectionCamera coverage, X-ray coverage, and the class the work is judged to
TestWhat the test covers, and what it does not
First articleHow many boards, who approves them, and what happens on a fail
Lead timeSplit into parts waiting, build, and test

Two of these lines carry more weight than the rest. The parts line and the first article line.

Parts are often most of the cost, and the shop makes money on them when it buys. That is not a reason to refuse, but it is a reason to ask which brand and which seller.

The first article is where the run is agreed. Without it, the first batch is the first article, and a fault found there is already a batch of faults.

The sheet these lines belong on is the same document for every shop you ask. Send one file, get answers you can line up side by side.

Who Buys the Parts Changes the Risk

There are two ways to run an order, and they are not close in risk. You supply the parts, or the shop supplies them.

When you supply the parts, you control the source and you carry the loss. A reel that arrives short or wrong stops the line, and the line still bills for the time.

When the shop supplies the parts, the price covers the parts and the risk moves with them. The trade is that you no longer know what went on the board unless the shop tells you.

The middle path is worth knowing. The shop buys, and the order names the brand and the seller for the parts that matter. Long lead parts, and any part that carries a safety mark, belong on that list.

Ask one question about sourcing that most buyers skip. Does the shop buy from a seller with a line back to the maker, and can it show that line on the invoice.

A part bought from a broker has no such line. That is not always a fault, but it is always a fact you should know before the boards are built.

Test: The Difference Between Working and Lasting

A test proves the board works on the day it is tested. It says nothing about the year after, so the type of test tells you what the shop is willing to promise.

The simplest test powers the board and checks the main functions by hand. It catches a dead board and misses a weak joint.

A bed-of-nails test puts the board on a fixture with pins that touch every net. It catches a wrong part value and a short, and it needs a fixture built for your board.

A flying probe test does the same job with moving pins and no fixture. It suits small runs, and it is slower on a large one.

Ask which of the three the quote covers, and ask what share of the boards is tested. A quote that says tested without a number is a quote that tested one board.

Then ask what happens to a failed board. Rework, scrap and a credit are three different outcomes, and only one of them is written down in most orders.

What Changes When the Line Is in China

Most SMT work for export runs in a cluster around Shenzhen and Dongguan, with a second belt further north. The cluster exists because parts, stencils, ovens and people who know them sit within a short drive.

That is a real advantage on a first build. A missing reel can be replaced in a day, and a stencil can be recut overnight. In a market with no parts trade, the same problem costs a week.

The risk sits in the middle layer. Many firms that answer an enquiry are not the firm that runs the line. They book capacity with a workshop and add a margin.

This is not a trick, and it is not always a problem. It becomes a problem when the fault is found later and nobody knows which shop touched the board.

Ask three questions and the layer becomes visible. How many lines do you run. Which machines are on them. Who owns the building.

A firm that runs its own line answers with machine names and a street address. A firm that books capacity answers with a delivery date.

What a cable order has to state shows the same discipline on a simpler product. The questions do not change with the product. Only the numbers do.

Six Faults, and Which Step Causes Each

Almost every board fault traces to one step, and knowing the step tells you which record to ask for.

A bridge is two pads joined by solder. It comes from the print, when too much paste lands between two pads.

A tombstone is a part standing on one end. It comes from the reflow, when one side of the pad heats faster than the other.

A cold joint is dull and weak, and it forms when the oven never reached the heat the paste needed. It passes a camera and fails in service.

A missing part is a reel that ran out or a nozzle that missed. The machine logs it, so the record exists if anyone reads it.

A part in the wrong place, or the wrong way round, is a loading error. It is the fault a camera cannot find and a test can, if the test was written for that part.

Warpage is the board bending after the oven. It comes from uneven heat or from a panel with too much metal on one side, and it shows as a crack months later.

The Paper the Shop Can and Cannot Give

An assembly shop can give you process records. It cannot give you the approval for the finished product, and buyers mix the two up constantly.

A device that can emit radio energy needs an equipment authorisation before it is sold in the United States. Part 15 of the Federal rules covers that, and the section on unintentional radiators is where a board with a clock line lands.

Part 15 of title 47 sets out who needs the authorisation and what it covers. The shop that soldered the board is not the party holding it.

For Europe the paper is different and the logic is the same. The directive on hazardous substances limits what may be in the parts, and the seller carries the duty to show it.

Directive 2011/65/EU is the rule, and the practical request is a materials statement per part, kept with the order.

What the shop can give is narrower and more useful. The oven printout, the camera report, the X-ray images and the test log. These four are the proof the process ran.

Ask for the same four with every batch, not once at the start. A capability shown in month one says nothing about the run in month nine.

How the two marks are actually tested covers the product side, and it is the right next read after the process side.

Questions Buyers Ask About SMT Assembly

What does SMT stand for?

Surface mount technology. The parts sit on the surface of the board, on metal pads, and are held by solder, with no leg passing through.

Why can I not judge a board by looking at it?

Because the joint is under the part. A camera can find a missing part, and only an X-ray or a test finds a joint that formed badly.

Should I buy the parts or let the shop buy them?

Let the shop buy them if you want one price and one party to blame. Buy them yourself if you need a named brand, and expect to carry the loss on a short reel.

How many boards should the first article be?

Enough to test the process, not the design. Two or three boards from the start of the run show what the line does before the batch is committed.

Do I pay for the stencil?

Usually yes, as a one-off line. Ask whether it is cut for your file revision, and who keeps it between runs.

Is SMT assembly the same as PCB assembly?

PCB assembly is the wider job, and it can include through-hole work, housings and test. SMT assembly is the surface mount part of it.

The Bottom Line

SMT assembly is five steps, and the setting behind each step is the thing you are buying.

Ask for the five settings, the ten quote lines and the four records, and the price stops being the only difference between two shops.

PROCESS CHECK

Send the Board File

Send the board file, the parts list and the batch size. We will ask the shop for the stencil thickness, the measured oven profile and the test coverage, then score the reply against all ten quote lines and tell you which ones it left out.

Send the File

Questions & Comments

We read every one and reply within 24 hours

Been shown a camera and told everything is inspected? Ask how many boards it checked and how often it calls a fault that is not one. We will tell you which record to request.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x