Enamel Pin Manufacturer: The Mould Decides
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Enamel Pin Manufacturer: The Mould and the Fill Decide

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder, Sourcing Pioneer
· Updated October 28, 2026 · 9 min read

An enamel pin is a small piece of metal with colour poured into it. The metal is cut from a mould, and the colour is filled by hand. The difference between a pin that sells and one that looks cheap is decided before anyone quotes. The sheet that fixes the mould, the fill and the plating is where the order is settled.

Studio still life on a flat cream surface showing two enamel pins, one with a smooth polished surface and gold plating, one with recessed colour and silver plating, plus a butterfly clutch beside them, with a navy serif headline reading ENAMEL PIN and an amber subhead reading MOULD FIRST
Two families, one difference: the surface is either polished or left recessed.

The Short Answer

Four choices come before artwork: soft or hard enamel, die struck or die cast, plating and attachment.

The mould is charged once per design. The fills cost per colour and they are done by hand.

So the first question is not the price per pin. It is how many colours the design needs and how fine the smallest detail is.

What a Pin Is Made Of

A pin is a metal body, enamel fills, a plating and a back attachment.

The body is stamped or cast from a mould. The channels in the body hold the colour.

The depth of those channels matters. A shallow channel holds less colour and shows the metal at the bottom, which reads as a thin fill.

Ask how deep the channel is on the sample. It is the difference between a pin that looks painted and one that looks cast.

The plating is the metal finish on the raised lines. It is what catches the light and what wears first.

The attachment is soldered or pressed on the back. It is the part a customer touches and the part that fails first when a pin is dropped.

Die Struck or Die Cast

Die struck means a metal sheet is pressed into a mould under high force. It gives sharp edges and fine lines.

Die cast means molten metal is poured into a mould. It gives a softer shape and a heavier body, and it holds detail less well.

Most designs with lettering go die struck, because a fine line survives the press. A chunky shape with rounded edges can go either way.

Ask which method the quote uses. Two prices for the same artwork often differ there.

A struck die wears with use. Ask how many impressions the shop expects before the die is re-cut, because a worn die rounds the sharp edges that make a design read.

Soft Enamel or Hard Enamel

This is the choice buyers notice and rarely understand.

Soft enamel fills the channels and stops below the metal line. You can feel the ridges with a finger, and the pin catches light unevenly.

Hard enamel fills the channels, then the whole face is polished flat. The surface is smooth, the lines sit flush, and the pin feels like a solid object.

Hard enamel costs more because of the extra polishing step. It also resists wear better, because there is no ridge to catch on cloth.

Ask which one the sample is. A photograph cannot tell you, and a supplier who sends a photo has not answered the question.

Ask too how many polishing passes are included. A single pass leaves fine scratches that show on a dark fill.

Polishing also softens the metal line. A line that is one millimetre wide before polishing may be half a millimetre after. That is why a fine design should be drawn heavy, then checked on the polished sample.

Plating: The Finish That Wears

Plating is the metal colour on the raised lines: gold, silver, nickel, black nickel, copper or an antique finish.

It is the first thing to wear. A pin carried loose in a pocket loses its gold at the edges within weeks.

Ask for the plating thickness. A thin plate costs less and wears through to the base metal, which shows as a dull grey line.

Ask how many pins go into a plating bath at once. A crowded bath plates unevenly, and an uneven plate shows on a flat polished face where there is nowhere to hide.

Some markets limit nickel release on items that touch skin for long periods. Ask whether the plating is nickel free, and ask for it in writing.

An antique finish is a deliberate darkening. It hides wear and it makes fine detail harder to read, so it suits a bold design only.

TypeSurfaceBest for
Soft enamelRecessed, ridges feltBold graphics at a low price
Hard enamelPolished flatPremium pins and fine lines
Printed and domedFlat print under resinPhotos and gradients
Die cast softRounded and heavyChunky shapes with no fine text

Colour Count and Pantone Matching

Each colour is a separate fill, done by hand with a small nozzle or a brush.

So colour count is the main cost step after the mould. Two colours are quick. Eight colours need eight passes and a steady hand.

Ask for the Pantone references, then ask what happens when a reference cannot be matched in enamel. Some brights cannot, and the substitute has to be agreed before the run.

Ask how the supplier checks colour between pins. A fill done by hand drifts, and a batch with two reds looks wrong on a backing card.

The check is usually a physical standard pin kept on the bench. Ask whether one exists, because a photo on a phone is not a standard.

Flat vector diagram on a cream background with four labelled columns reading MOULD, ENAMEL, PLATING and CLUTCH inside one outlined strip, with the note ONE IS PAID ONCE.
Four decisions, one of them a one-off cost.

Size and Thickness

Size is measured across the widest point in millimetres. Thickness is the body, before the attachment.

A small pin cannot hold fine text. Below a certain size the lines merge and a word turns into a smudge.

A thick body feels substantial and sits away from the cloth, which makes a soft enamel pin wobble.

Ask for the size and the thickness, then ask what the smallest legible letter height is at that size. A supplier who knows will give a number.

A pin under twenty millimetres is a badge, not a poster. A design with six words will fail at that size and succeed at forty.

The Clutch and the Back

The attachment decides whether the pin stays on a jacket.

A butterfly clutch is the standard. A rubber clutch grips harder and is easier on thick fabric.

A magnet needs no hole and ruins nothing, and it falls off on a heavy coat. A safety pin suits a pin that will not be worn every day.

A deluxe clutch is a locking version and costs more. It is the answer for a pin sold at a premium.

Ask what the clutch is made of. A plated clutch tarnishes and can mark a shirt; a plastic backed clutch does not.

Ask what the back is stamped with. A back stamp is free in most moulds and it is where a brand puts a name or a year.

Five Tests Before the Batch

Scratch, colour, fill level, clutch and nickel. Five tests cover almost every complaint.

The scratch test drags a fingernail across a flat area. A hard enamel pin resists; a soft one shows a mark in the recess.

The colour test compares three pins from the batch against the approved sample under daylight, not under a desk lamp.

The fill level test looks at a soft enamel pin from the side. A fill that sits too low shows a deep channel and collects dirt.

The clutch test attaches and removes a clutch twenty times. A clutch that loosens will drop the pin.

The nickel test is a lab item. If the pin touches skin, ask for the report, not a promise.

Test methods for coatings and metal finishes are published by standards bodies, and the standards body that writes the procedures names the procedure for each.

A check on the filled pins catches the batch where one colour was mixed a shade off, which a photograph will never show.

Nine Lines a Pin Quote Needs

LineWhat it must state
MethodDie struck or die cast
EnamelSoft or hard, and the polish passes
SizeMillimetres across, and thickness
ColoursCount, and Pantone references
PlatingFinish, thickness, nickel free or not
ClutchType, and whether it locks
BackStamp, and its position
MouldCost, and who owns it
PackingBacking card, bag, and carton count

The mould line is the one to read twice. A mould charged per design and kept on file makes a reorder cheap; a mould charged every time makes it expensive.

Read the packing line at the same time. A pin sold on a card needs a card for every pin, and the card order is often placed later at a worse price.

When It Is Not Enamel

Two other products look like enamel pins and are not.

A printed pin is a flat metal disc with a printed face and a clear dome over it. It reproduces a photograph and it cannot hold metal lines.

A silk screen pin is printed on metal with the same limits. Both are cheaper for a photo and poorer for a bold graphic.

Ask which process the quote covers. A buyer who orders “soft enamel” and receives a dome pin has bought a different product at an enamel price.

Minimums and Mould Ownership

A pin order has two minimums: the mould run and the fill run.

The mould is cut once per design and used for every pin in that shape. The fill run is the number of pins that can be filled before the batch is closed.

That is why a small order in eight colours costs more per pin than a small order in two. Each fill pass has a setup of its own.

Ask whether the mould is kept and for how long. A design held on file makes a reorder cheap, and a design scrapped after a year has to be cut again.

The clause that keeps the mould in your name matters here more than in most categories, because the mould is the design.

Where Pins Are Made

Pin production clusters with small metal work, because the body is stamped or cast and the plating is a separate workshop.

So a supplier that offers pins and badges may be brokering the plating. Ask which steps happen in house.

Ask how many fillers work on a batch. Filling is hand work, so a large order is spread across people, and that is where colour drifts between pins.

Ask what the reject rate is on a complex design. A supplier who names a figure has run that design type before.

Backing Cards and the Last Cost

Most pins are sold on a printed backing card, in a small bag.

The card is a design item and a cost item. It holds the pin, shows the brand and often carries a barcode.

Ask whether the card is printed in house, and what the carton count is with the cards included. Cards are light and they take up space. Space is what a forwarder bills.

Ask for the card weight as well. A light card bends inside a bag; a heavy one costs more and photographs better.

How a forwarder bills a light carton is the last line in the sum. A small carton has a minimum charge that a buyer forgets.

On the import side, the tariff line depends on the metal and on how the pin is made. A plated metal pin and a printed badge are not the same article. the commission’s own tariff lookup is where the line is fixed.

Questions Buyers Ask About Enamel Pin Suppliers

Soft or hard enamel: which sells better?

Hard enamel reads as premium and wears better. Soft enamel is cheaper and shows the metal lines more strongly.

Why does my small text look like a smudge?

The pin is too small for the letter height, or the mould was cast rather than struck.

Can I match a Pantone colour exactly?

Often, not always. Some brights cannot be mixed in enamel, and the substitute has to be agreed before the run.

Will the gold plating wear off?

On a pin carried loose, yes. Ask for the plating thickness and keep the pin on its card.

Do I own the mould?

Only if the order says so. Ask for it in writing, because the mould is the design.

What clutch should I choose?

Butterfly for standard, rubber for thick cloth, locking for a premium pin, magnet where no hole is allowed.

The Bottom Line

Choose the method, the enamel and the plating before artwork, then count the colours and check the smallest letter. Those three decide whether the pin looks worth its price.

A flat polished face and an even fill are worth more than a cent saved on plating. The cent is invisible and the worn edge is not.

MOULD FIRST

Send the Artwork

Send the design, the size you want and the colours you need. We will say whether the detail survives the mould, price soft and hard enamel side by side, and show what the mould costs per pin at your volume.

Send the Artwork

Questions & Comments

We read every one and reply within 24 hours

Got pins where the text filled in, or a plating that wore off in a month? Send the artwork and the size. We will say which of the four choices was never made.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x