DWR Coating: What It Is, Why It Stops Working, and What the Law Now Says
DWR is a finish on the outside of the fabric that makes water bead and roll off. It is not what keeps you dry: the membrane or coating underneath does that. DWR just stops the outer fabric from soaking up water and feeling cold.
Two types are in use today. One holds fluorinated compounds and is being pushed out of clothing. The other is PFAS-free and performs a little worse.
That choice stopped being a choice in 2025. A California law now bans PFAS over the cap in new textile articles sold in the state, with a cap that tightens again in 2027.
So this page has four things. What the finish does, the three chemistries, the law as written, and why a working DWR stops working.
What the Finish Does, and What It Does Not
A waterproof jacket is a system of three parts. The face fabric takes the abrasion. The membrane or coating blocks liquid water. The DWR keeps the face fabric from soaking up water.
When the face fabric wets out, two things happen. The jacket gets heavy and cold on the skin. The membrane then stops breathing, because vapour can no longer pass through the water sitting on the outside.
That is why a jacket can be fully waterproof and still feel wet. The membrane works and the finish does not.
DWR is a surface treatment, a few molecules thick, applied at the mill and cured. You cannot see it, and it is not the same thing as the waterproof coating on the inside of the fabric.
| Layer | What it does | If it fails |
|---|---|---|
| Face fabric | Takes abrasion and wind | Nothing protects the membrane |
| DWR finish | Makes water bead and run off | The face wets out and breathing stops |
| Membrane or coating | Blocks liquid water | You get wet through |
Three Chemistries, and Why Two Are Leaving
DWR chemistry is named by the length of its fluorinated carbon chain. The industry has moved from C8 to C6, and is now moving from C6 to C0.
C8. The first long-chain fluorochemical. It gave the strongest water, oil and stain repellency, and it was withdrawn because long-chain fluorinated compounds persist and add up.
C6. A six-carbon chain. It replaced C8 as the industry standard and gives strong water repellency with fair oil and stain resistance. It still holds PFAS, which is why it is now the chemistry under regulatory pressure.
C0. PFAS-free and hydrocarbon based. It gives fair water repellency, little oil and stain resistance, and it wears off faster than C6.
| Property | C6 | C0 |
|---|---|---|
| Water repellency | Strong | Moderate |
| Oil and stain resistance | Moderate | Limited |
| Durability of the finish | Degrades | Degrades faster |
| PFAS content | Yes | No |
Read the last row with the first two together. C0 is not a drop-in swap: it buys the certificate by giving up some oil resistance and some life. A buyer who specifies C0 without changing the test requirement is specifying a jacket that will wet out sooner.
The Regulation That Turned This Into a Buying Decision
California’s Safer Clothes and Textiles Act, AB 1817, was signed on 30 Sep 2022 and took effect on 1 Jan 2025. It is the first state law in the US to ban PFAS in clothing and textiles.
The rule is that no person may manufacture, distribute, sell or offer for sale a new textile article containing PFAS over the cap. The definition of a textile article is broad, and it names clothing, accessories, backpacks, draperies, upholstery, bedding and towels among others.
The cap is measured as total organic fluorine. It starts at 100 parts per million in 2025 and drops to 50 parts per million from 2027.
There is a disclosure duty as well. Outdoor clothing for severe wet conditions has an extension to 2028. From 1 Jan 2025 that clothing must still carry the line “Made with PFAS chemicals”.
The law also adds paperwork to the chain. The maker must give the seller a certificate saying the article holds no PFAS above the cap.
| Item | What the law sets |
|---|---|
| Signed | 30 Sep 2022 |
| Effective | 1 Jan 2025 |
| Limit, 2025 | 100 ppm total organic fluorine |
| Limit, from 2027 | 50 ppm |
| Severe wet weather outerwear | Extension to 2028, with a disclosure line from 2025 |
| Chain duty | Maker gives the seller a certificate on the article |
Two practical points follow. A C6 fabric is not banned as a fabric; what is banned is a textile article above the cap that is sold in California. And the exemption for severe wet weather clothing is temporary, so an item planned for 2029 cannot rely on it.
Exemptions exist elsewhere in the text, including carpets, rugs, treatments for converted fabric and protective equipment for critical uses such as firefighting. Those are narrow, and none of them covers plain outerwear.
Why a Working DWR Stops Working
The finish is thin and it sits on the face. Anything that coats or rubs that face strips it off. Three causes cover most cases.
Dirt and body oils. The finish repels water because its face has low energy. Oil has lower energy still, so it spreads onto the fabric. That bridges the finish, and water then follows the oil.
Abrasion. Shoulders under pack straps, cuffs and knees lose the finish through friction. This is why a jacket that still beads at the chest can wet out at the shoulders.
Washing. Detergent residue left in the fabric attracts water. A jacket washed in plain soap and not rinsed properly behaves as if it had no finish at all.
The usual fix is heat. A clean, damp jacket tumbled on a low setting often brings the beads back. Heat turns the finish on the fibre face.
When heat no longer helps, the finish is gone, not disturbed. A spray-on product is then the answer. That is also the point where the chemistry matters, because a wash-in item applied over a mill finish is a different system.
What Happens at the Mill
The finish is applied as a liquid and fixed with heat, and the fixing step is where most of the performance lives.
In the usual route the fabric passes through a bath holding the finish, then through rollers that set how much liquid it keeps. It is dried, then cured at a set heat for a set time. The cure is what bonds the chemistry to the fibre face.
That explains a result buyers find confusing. Two mills can quote the same chemistry and deliver different results, because the pick-up and the cure heat were not the same. A finish under-cured for a few seconds looks identical on the roll and fails in the wash.
Fabric construction matters too. A tight, smooth weave beads water readily; a soft, brushed or high-loft face holds it, because the fibres stand up and trap the droplets. A finish that scores well on a plain woven jacket can score lower on a brushed face without much being wrong with the chemistry.
Two Tests, and They Measure Different Things
Buyers mix these up constantly, and the mix-up makes jackets that fail in the field while passing the papers.
The spray test rates how water beads and runs off the face fabric, on a scale from 0 to 100 in steps of 10 under the AATCC 22 method. It shows the finish.
The water pressure test shows the pressure at which liquid water passes through the fabric, in millimetres or in pascals. It shows the barrier, not the finish.
A fabric can score 100 on spray rating and still have a weak barrier. It can also hold a high water pressure test and wet out in ten minutes once the finish is gone. That feels worse to the user than a lower barrier that beads.
So a specification needs both figures, plus the wash cycles they were tested after. A spray rating quoted on new fabric says nothing about the jacket after twenty washes, and that is the number a buyer feels.
The Care Label Often Works Against the Finish
Most jackets carry a care label written to protect the membrane, not the finish. The common wording tells the owner to wash cool and air dry, which protects everything except the one thing that can be restored.
Heat is what turns the finish on the fibre. A jacket that is never warmed after washing keeps the finish lying flat, and the beading fades earlier than it needs to.
The better wording allows a low tumble dry or a warm iron over a pressing cloth, and says why. It also tells the owner to use a technical wash, not a soap with softener. Softener is made to coat fibres, and a coat of softener is exactly what blocks a water-repellent surface.
This is a cheap line to fix. It costs one sentence on the label. It also changes how many buyers come back at month six saying the jacket has stopped working.
Six Lines for a DWR Fabric Specification
A fabric order that can be checked has six things written down. Each one closes a gap that a mill’s own data sheet leaves open.
The chemistry, by name. C6 or C0, and whether the mill claims PFAS-free. A finish described just as “DWR” tells you nothing about which of the two you are buying.
The fluorine figure, with the method. Total organic fluorine in parts per million, the laboratory and the date. This is the number the California cap is tested on, not the marketing claim.
The spray rating, and after how many washes. A figure on new fabric alone is not a specification, because the buyer judges it after twenty washes.
The water pressure test, with the method. Separate from the spray rating, and stated in the units the test used.
The certificate on the cap. A paper from the maker saying the article holds no PFAS above the cap, which is what the California law puts in the sales chain.
The care instruction. Wash heat, soap type and the heat-restore step. A finish that could be revived is wasted if the label tells the buyer to air dry.
| Spec line | Why it matters | How to check it |
|---|---|---|
| Chemistry by name | C6 and C0 are different products | Ask for the finish data sheet |
| Fluorine in ppm | The legal cap is tested here | Third-party lab report, dated |
| Spray rating and washes | New-fabric figures hide the field result | Test before and after washing |
| Hydrostatic head | Measures the barrier, not the finish | Report in the method’s own units |
| Certificate on the cap | The law puts a paper in the chain | Get it per shipment, not per year |
| Care instruction | A revivable finish is lost if the label says air dry | Read the printed label |
Once those six are written, you have a fabric sheet a mill can quote on. A check on the finished goods then has a spray rating and a paper to look for.
Where a run fails on the finish, the cost question has its own rules. What a failed finish is worth is settled by the sheet, and a spray rating quoted after twenty washes is the line that settles it.
On a repeat programme, a check while the fabric is still in the mill catches a chemistry swap before the cut. That is the only stage where a C6-to-C0 change is still cheap.
The same logic applies to a sock blend. The chemistry on the papers is what you buy, and the finished item cannot show you which one arrived.
Questions Buyers Ask About DWR Coating
Does DWR make a jacket waterproof?
No. The membrane or coating does that. DWR stops the outer fabric soaking up water, which keeps the jacket light and lets the membrane breathe.
What is the difference between C6 and C0 DWR?
C6 holds fluorinated compounds and repels water, oil and stains well. C0 is PFAS-free and repels water moderately, with little oil resistance and a shorter life.
Is C6 DWR banned?
The chemistry is not banned. In California, a new textile article above the PFAS cap cannot be sold, and that cap drops from 100 to 50 ppm in 2027.
How do I restore a DWR finish?
Wash it clean, then apply heat. A low tumble dry or a warm iron over a pressing cloth often brings the beads back. If it does not, the finish is gone and needs reapplying.
Why does my jacket wet out at the shoulders first?
Because pack straps abrade the finish. Abrasion strips it in patches, so the chest still beads while the shoulders soak.
What test proves a DWR is working?
The spray rating, on the AATCC 22 scale. Ask for it after a stated number of washes, because a new-fabric figure says nothing about the jacket in use.
The Short Version
DWR keeps the face fabric from soaking up water, and it does nothing for the barrier underneath. It fails from dirt, oil and abrasion, and heat often brings it back.
Which chemistry you buy is now a legal question as well as a performance one. The order needs the chemistry, the fluorine figure and a certificate on the cap.
C6 or C0 Changes the Order
Specifying a DWR finish and the mill quotes both types at the same price? Send the finish data sheet, the fluorine result and the market you sell in. We will say which line the certificate has to cover and after how many washes the spray should hold.
Send the Brief
Questions & Comments
We read every one and reply within 24 hoursTwo mills quoting the same DWR at the same price, one C6 and one C0? Send both finish data sheets and the fluorine result, and we will say which line the certificate has to cover.