Barbell Types: 28 mm, 29 mm and the Marks That Tell
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Barbell Types: What the Numbers on the Page Do Not Tell You

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 2, 2026 · 11 min read

A barbell is three parts: a shaft you grip, two sleeves that carry the plates, and the knurl cut into the shaft. Almost every type you read about is a change to one of those three, and the change is usually measured in millimetres.

That is why the names on a sales page tell you so little. Two bars can both call themselves Olympic, both be 20 kg, and still feel nothing alike. The difference sits in the shaft diameter and in one distance stamped into the bar.

So this page is about the measurements, not the labels. First what each part does, then the two sizes the sport fixed. After that the three families that matter for buying, and the figures worth writing on an order.

Warm beige studio still life of a steel barbell shaft section with knurled grip beside a folded specification sheet and a caliper
Three parts, and the numbers that separate them.

Three Parts, and What Each One Decides

The shaft is the tube your hands hold. Across the market its diameter runs from 25 mm to 50 mm, which is a factor of two in a part you wrap a hand around. A thinner shaft bends more under a heavy pull and sits deeper in the palm.

The sleeve is the tube at each end that the plates slide onto. On an Olympic bar the outer end of the sleeve is 50 mm across, which is why Olympic plates have a two-inch hole. Bars built for a one-inch hole are a different family, and the hole in those plates runs from 27 mm to 31 mm.

The knurl is a crosshatch pressed into the shaft. It is the only part of the bar that touches skin, and it is the part buyers describe worst. A deep, sharp knurl holds chalk and a hand; a shallow one lets a heavy pull slip.

Rotation is the fourth thing to ask about, though it hides inside the sleeve. A bushing is a plain bronze ring. A bearing is a rolling element. A weightlifting bar needs to spin so the lifter can turn under it. A power bar barely needs to spin at all.

PartWhat it decidesWhat to check on the order
ShaftFlex, hand feel, how the bar sitsDiameter in millimetres
SleevePlate fit and how the bar turnsOuter diameter and the rotating part
KnurlGrip, and wear on the handDepth and where it is left smooth

The Two Sizes the Sport Fixed

Competition weightlifting settled on two bars, and both are still in use. The men’s bar weighs 20 kg and is 2.2 m long, with a 28 mm shaft. Its grip marks sit 910 mm apart.

The women’s bar is 15 kg, with a 25 mm shaft, and it is not a scaled copy of the men’s bar. It carries no centre knurl. That patch sits in the middle of the shaft, where a men’s bar rests across the back in a squat.

Plates of 10 kg and up are 450 mm across. That is quiet good design. The bar starts at the same height off the floor whether it holds one plate or six, The first pull of a lift never changes.

MeasureMen’s Olympic barWomen’s Olympic bar
Weight20 kg15 kg
Length2.2 mShorter, per the sport’s rules
Shaft diameter28 mm25 mm
Grip marks910 mm apart910 mm apart
Centre knurlYesNo

Collars change the weight on the box. A pair can weigh up to 2.5 kg each, so a 20 kg bar with its collars can leave the factory as 25 kg. That is the figure a freight quote is built on, not the number printed on the end of the shaft.

Both sizes and the 450 mm plate figure are recorded in the reference entry on the barbell. That is the version of the numbers a factory can check too.

A mixed gym that orders “twenty kilo bars” for everyone has bought the men’s bar for half its lifters. The 3 mm difference in shaft diameter is the difference between a hand closing around the bar and a hand resting above it.

The Power Bar, and What One Millimetre Does

Powerlifting uses a stiffer bar, because the lifts are slow and a whippy bar wastes the effort. The power bar is 29 mm at the shaft, and its grip marks sit 810 mm apart, closer than the 910 mm of an Olympic bar.

That 100 mm difference in the marks is the cheapest way to identify a bar you have been quoted. Put a tape on it. A bar with 910 mm marks was built for weightlifting; 810 mm belongs to powerlifting.

Length splits the sports too. Bars longer than 2.2 m are used mainly by powerlifters, because the extra length adds flex at the ends without changing the grip. A long bar and a short bar can carry the same plates and feel like two different tools.

Between the two sits a third size, and it sells well for a reason. One common multi-purpose bar is 28.5 mm, which is between the 28 mm weightlifting and the 29 mm powerlifting standard. It suits a gym that trains both sports and does not want two sets of bars.

The trade-off is real but small. A 29 mm shaft is stiffer in the hand and harder to hook grip. A 28 mm shaft whips more, which helps a clean and hurts a squat.

Panel comparing 25, 28, 28.5 and 29 millimetre shaft diameters and the grip mark spacing used by each sport
Four diameters, two grip-mark spacings, and the sports they belong to.

Six Specialty Bars, and the Job Each One Does

A specialty bar is a bar that traded general use for one job. None of them is a better barbell; each is a tool that makes one movement easier to load or easier on a joint.

The trap bar is a hexagon you stand inside. Its two sets of knurled handles run parallel to the body. That puts the load in line with the middle of the foot, not in front of it. On one common model the handles measure 1.34 inches across and sit 25 inches apart, and the frame is welded from 1.5 inch square tube.

The curl bar is bent so the wrists sit at an angle. The bend is small, the effect on the wrist is not. One model has a 28.5 mm shaft in 110,000 PSI steel, and its sleeves sit 31.5 inches apart, so it cannot be racked like a straight bar.

The safety squat bar carries the load on a yoke across the shoulders with handles in front. It lets a lifter squat while holding nothing, which matters after a shoulder injury.

The log bar is a cylinder with handles inside it, used in strongman. The axle bar is simply a thick shaft, up to 50 mm, which is why it is hard to hold. The Swiss bar has several pairs of neutral handles along one shaft, so one bar offers four or five grip widths.

BarShapeBest forWatch out for
Trap barHexagon, neutral handlesDeadlift with less lower-back strainNeeds floor space and a wide stance
Curl barCambered shaftArm work with a straighter wristShort sleeve spacing, hard to rack
Safety squat barYoke with front handlesSquat with no hand loadDifferent balance from a straight bar
Log barCylinder with inside handlesOverhead press, strongmanAwkward to store
Axle barThick plain shaft, up to 50 mmGrip strengthVery hard to hold without straps
Swiss barSeveral neutral handle pairsPress and row with a neutral wristOne fixed width per pair

The Numbers on the Page, and Which Ones Mean Something

Product pages lead with a weight rating, usually a large round number. It is worth knowing what that number is. It is not a test result. At least one major maker refuses to print one at all, and says why on the bar’s own product page. The maker calls a static weight rating misleading.

What that maker prints instead is tensile strength: 190,000 PSI on a bar with a 28.5 mm shaft. And its own wording explains why that figure has an optimum, not a maximum. Steel that is too hard does not bend, it snaps, and a bar that snaps is worse than a bar that flexes.

Length is another figure that is usually stated and rarely checked. The same bar is 86.75 inches long, with 51 7/8 inches between the sleeves. That shaft length is what decides whether it sits on the rack you already own.

The last number is a service life, and it is the only one expressed in years. That same bar carries a rating the maker says is good for 16 years in a high volume gym. A buyer comparing two quotes can ask for the same kind of statement, in years, and not another round number in pounds.

Six Lines for a Barbell Order

A bar order that can be checked has six things written down. Each one closes a gap that a product photo leaves open, and each one is a number or a named part and not an adjective.

The use, stated first. Weightlifting, powerlifting or mixed. That single line decides the shaft diameter and the grip marks, so it belongs above any specification.

The shaft diameter in millimetres. Not “competition grade”. A 28 mm bar and a 29 mm bar are different products with different feel, and the difference is invisible in a photo.

The grip mark spacing. 910 mm or 810 mm. It is the line that catches a factory swapping a power bar for a weightlifting bar on a repeat order.

The rotation type. Bushing or bearing, and how many. It changes the price and it changes how the bar behaves overhead.

The tensile strength, with the steel named. In PSI, with the grade stated. A figure with no steel behind it cannot be checked by anyone.

The knurl spec and the finish. Depth, the width of the smooth band, and the coating. Two bars can share every other number and feel completely different in a hand.

Spec lineWhy it mattersHow to check it
Stated useDecides every number below itRead the bar against the sport’s rule
Shaft diameterFeel, flex and gripCaliper on three points of the shaft
Grip marksIdentifies the sport it was built forTape measure, 910 or 810 mm
RotationOverhead behaviour and priceSpin the sleeve by hand, count parts
Tensile strengthResists bending without brittlenessAsk for the steel grade and the report
Knurl and finishGrip, hand wear, corrosionSample bar in hand, not a photo

Once those six lines exist, you have a written sheet a bar factory can quote on, and two quotes become comparable. The same numbers become the checklist for the load test on a finished batch.

If a batch fails on diameter or knurl, the money question has its own rules. What a failed batch is worth is settled by the sheet, not by the argument after delivery.

The tensile figure rewards the same reading as any other steel order, where harder steel is not always better. A bar and a blade fail in opposite ways: one bends, the other chips.

Panel listing six specification lines for a barbell order with the check method beside each one
Six lines, each one a number or a named part.

Questions Buyers Ask About Barbell Types

What are the main types of barbell?

Three families cover most buying: the Olympic weightlifting bar at 28 mm, the power bar at 29 mm, and the specialty bars. Specialty covers the trap bar, curl bar, safety squat bar, log, axle and Swiss bar.

What is the difference between a 28 mm and a 29 mm bar?

One millimetre of shaft. The 28 mm bar flexes more, which helps a clean and suits weightlifting. The 29 mm bar is stiffer in the hand, which suits a slow squat and a heavy pull.

How can I tell a power bar from an Olympic bar?

Measure the grip marks. They sit 910 mm apart on a weightlifting bar and 810 mm apart on a power bar. Shaft diameter confirms it at 28 mm against 29 mm.

Do I need a women’s bar for a mixed gym?

If the gym trains women for competition, yes. The women’s bar is 15 kg with a 25 mm shaft and no centre knurl. Ordering 20 kg bars for everyone gives half the lifters a shaft that is too thick.

What is a trap bar good for?

Pulling with the load beside the body instead of in front of it. That reduces the strain on the lower back, and it is why the trap bar is common in gyms that train older or returning lifters.

Is a higher weight rating better?

Not on its own. A static rating is not a test result, and one major maker refuses to print one because it misleads. Ask for tensile strength with the steel named, and for a service life in years.

The Short Version

A barbell type is a set of measurements, not a name. Shaft diameter, grip marks, rotation and knurl decide how a bar feels and what it is for.

The two fixed sizes are the 28 mm weightlifting bar and the 29 mm power bar, with grip marks at 910 mm and 810 mm. Everything else is a specialty shape, and a specialty bar is a tool for one job and not an upgrade.

DIAMETER AND MARKS

Two Quotes, One Sheet

Quoted two bars at the same price and neither sheet states a shaft diameter or a grip mark spacing? Send the two pages and the sport you train for. We will tell you which questions to put back to the factory before a sample is cut.

Send the Brief

Questions & Comments

We read every one and reply within 24 hours

Two bars quoted at the same price, one 28 mm and one 29 mm? Put the shaft diameter and the grip mark spacing in a comment and we will tell you which sport each one was built for.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x