What Is Brass Jewelry? Alloys, Lead And Cost Per Piece
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

What Is Brass Jewelry: A Base Metal That Shows Its Age

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 16, 2026 · 10 min read

Brass jewelry is copper and zinc, and the zinc is what makes it cheap.

That sentence explains the whole category. Copper gives the warm tone people pay for, and zinc does the boring work of making the metal hard enough to keep a shape.

Brass is usually more copper than zinc, at roughly two to one. Move that ratio and the colour moves with it.

More copper gives a softer metal with a pink or gold tone. More zinc gives a harder, paler metal that can look silvery at the extreme.

Two brass rings, one polished gold tone and one paler yellow, on a beige studio surface
Two brass tones, one alloy family, and a colour that moves with the copper share.

What The Metal Is

Brass is a copper alloy with zinc in it, and the two metals mix at the atomic level rather than as grains. That is why it casts cleanly and takes a polish.

Two numbers matter more than any trade name. Density runs from 8.4 to 8.73 grams per cubic centimetre, and melting starts around 900 degrees Celsius.

Both numbers are lower than the ones for silver. Less heat means cheaper casting, and less weight means less metal per piece.

Supply is not a worry either. Most brass alloys in circulation are made from recycled metal, and the scrap trade is old and liquid.

That combination is why the metal appears in fashion lines, in hardware, and in the fittings that hold a piece together. A chain decides how much of it you buy, and how much scrap comes back.

What brass is not is a precious metal. It has no assay mark, no bullion value, and no promise that it will still look the same in a year.

So the honest description is this: a cheap, workable, good-looking base that needs a finish and a warning. Everything later in this article follows from that.

The Alloy Chart, And Why Names Mislead

A supplier will quote you a trade name. Red brass, gilding metal, cartridge brass, free-machining brass. None of those names fixes a composition on its own.

Two documented examples show how far the copper share can move. Red brass C230 runs 84 to 86 percent copper, with the balance mostly zinc.

Corrosion-resistant brass C352 sits near 61 to 63 percent copper and 30 percent zinc. It also carries lead and a trace of arsenic.

One is warm and workable. The other is built for plumbing and is a poor choice for a necklace. Same family, different jobs.

What the sheet saysCopper shareWhat you getWhere it belongs
Red brass, C23084 to 86 percentWarm red-gold tone, softerVisible parts, bezels, plaques
Corrosion-resistant, C35261 to 63 percentPale yellow, tough, holds pressureFittings, not skin contact
Leaded brass for machiningBase variesEasiest to cut, least stable surfaceClasps and findings, with a test
Higher copper, above 85 percentUp to 95 percentSoftest, deepest gold colourStamped sheet, light wear

Read the row before the name. Two factories can both write “red brass” and ship alloys twelve points apart in copper.

The practical ask is simple. Put copper and zinc percentages on the drawing, then a maximum for lead, and treat the trade name as a label rather than a specification.

Colour follows the copper share, and hardness follows it in the opposite direction. More copper means a softer, warmer metal that dents and polishes easily.

More zinc means a harder, paler metal that keeps an edge and resists wear. If a buyer asks for a deeper gold, they are asking for copper and a higher metal cost.

Cost Per Piece, Worked Backwards

Brass is sold by the kilogram and silver by the gram. That unit gap, a factor of a thousand, is the reason a brass line can be priced to sell at all.

The arithmetic is short. Take the volume of the part in cubic centimetres, multiply by 8.4 to 8.73, and you have the weight in grams.

Divide that weight by a thousand and multiply by the price per kilogram. That is the metal cost of one piece, before anything else.

Nothing in that chain needs a live price. Put your own rate in and the sum works, which is useful when a quotation arrives without a breakdown.

StepInputOutputWhere it goes wrong
1 VolumeCAD model or drawingCubic centimetresWall thickness guessed
2 WeightVolume times 8.4 to 8.73Grams per pieceWrong alloy density claimed
3 Metal costGrams divided by 1,000, times price per kgCost per piecePrice quoted for a different grade
4 YieldPieces per kilo of barReal metal costRunner and scrap ignored
5 FinishPlating or lacquer areaAdded cost per pieceQuoted per batch, not per piece

Ask two more questions before the price means anything. The first is the minimum order, and it follows the process. A stamped part wants a press run, and a cast part wants a tree.

The second is the lead time after the mould. A brass line usually waits on tooling, not on metal. Metal arrives in days, and a new die does not.

Step four is where most quotations hide. Cutting a ring from a bar leaves swarf, and a cast tree leaves a runner, and both were bought at the same price per kilo.

Ask for pieces per kilo. A factory that knows its yield will answer in seconds, and one that does not will answer with a price.

The metal is rarely the largest line anyway. Plating, polishing, labour and packing usually beat it, which is why a cheaper alloy saves pennies and a cheaper finish saves dollars.

The Lead Question, Which Is Not Optional

Lead goes into brass for one reason. It makes the alloy easier to cut, and a free-machining grade can be turned into a clasp or a finding at a fraction of the cost.

The addition is small, often around two percent. The problem is not how much sits in the metal, but where it sits.

Lead melts before the rest of the alloy, so it gathers at the grain boundaries as small globules. Those globules reach the surface as the metal cools.

Cutting makes it worse. A tool smears the soft lead across the cut face, and that thin film is what a finger or a test wipe meets first.

So a low lead number on a mill certificate does not settle the question. The surface can carry more than the bulk average, which is why tests read the article and not the ingot.

Europe drew a hard line. Under REACH Annex XVII, entry 63, an individual part of a jewellery article cannot be placed on the market if lead reaches 0.05 percent by weight.

The wording matters twice. It is per part, not per product, and it is about being placed on the market rather than about being worn.

California got there earlier by a different route. A 1999 action against makers and sellers found brass keys over the state limit by an average factor of nineteen, on twice-daily handling.

The 2001 settlement cut lead to 1.5 percent or forced a warning, and plated keys were excluded from that deal. That exclusion belongs to the keys case, not to the European rule.

For a jewellery buyer the ask is narrow and cheap. Send the drawing, and request a lead figure per part with the test method named, not a phrase like “lead free”.

“Lead free” has no legal definition here, and it hides the difference between an alloy that never had lead and one that has 0.04 percent.

A leaded clasp and a clean pendant are not the same product, even when the drawing pairs them. Treat findings as their own parts with their own paperwork.

What The Metal Does To Air And Skin

Brass does not rust, because there is no iron in it. It corrodes, which is a different process with a different look.

Moisture, chlorides, acetates, ammonia and some acids all attack it. The copper reacts with sulphur first and turns brown, then black.

Leave it in slightly acidic water and the layer can oxidise further into a green patina. On a roof that is charming. On a ring it is a complaint.

The green mark on a finger is the same chemistry seen from the other side. Copper salts transfer to skin, and they are most visible on a warm, damp hand.

Zinc has its own weakness. In salt water it leaches out of the alloy and leaves porous copper behind, which is why brass plumbing fails near the sea.

Chlorine is the household version of that. A swimming pool is a hard place for a brass bracelet, and a bathroom is not much better.

There is a second corrosion path that catches plated goods. Brass touching gold or silver in a wet environment becomes the anode, so the base metal corrodes first.

That is why a scratch on a gold-plated brass ring can pit and spread. The plate is not just a colour, it is a barrier between two metals that do not agree.

Copper share scale for four brass grades with colour and hardness notes
Copper share drives colour and hardness at the same time, in opposite directions.

Bare, Lacquered Or Plated

Three finishes go on brass, and they fail in three different ways. The choice decides the price and the return rate together.

Bare brass is polished and left alone. It looks honest at first and ages fastest, and the customer becomes the person who maintains it.

Lacquer is a clear coat over polished metal. It holds the colour for a while, then wears through at the edges, where a ring meets a finger.

A worn lacquer coat is worse than none, because the film traps moisture against the metal in a line. The customer sees a tide mark, not a scratch.

Plating adds a real layer, usually gold on brass. Thickness is quoted in microns, and a plate under half a micron is a colour, not a coating.

Two numbers belong on the purchase order with the plating line. Microns at the wear point, and salt spray hours on a finished part.

Ask where the part was tested. A flat coupon passes a spray test that a sharp edge with the same plate would fail in a day.

What To Inspect At Goods-In

Six checks cover most brass failures, and every one of them can be done on a bench with a lamp and a scale. None of them replaces an inspection before the carton is sealed.

Colour across the lot. Line ten pieces up under the same light. A step between two of them means two alloy batches or two polishing runs.

Weight per piece. Weigh ten and compare with the drawing. A light piece means a thin wall, and a thin wall is where plating fails first.

The edges. Run a fingernail along a plated edge. A sharp lip holds less plate, and the plate is what the customer judges.

Lacquer under a lamp. Tilt the part and look for a dull band near an edge. That band is where the film has already thinned.

The clasp. Open and close it twenty times, then pull. Clasps are bought parts, and a bought part can carry its own lead and its own plating.

The paperwork. A lead figure per part, a plating thickness, and a salt spray result. Silver tarnishes on the same shelf, so the care card has to name the metal. Three sheets, not one certificate for the alloy.

Seven Lines For The Order Sheet

A brass order goes wrong in the gaps between documents. These lines close the gaps, and each one is short enough to paste into a purchase order.

One. Alloy by percentage: copper, zinc, and a maximum for lead, stated per individual part rather than for the bar.

Two. Weight per piece with a tolerance, plus the pieces per kilo the factory expects from its own bar.

Three. Finish named as bare, lacquer or plate, with microns at the wear point and a colour reference the factory can mix to.

Four. Salt spray hours on a finished part, and the area tested, which should be an edge rather than a flat coupon.

Five. Findings listed separately: clasp, post and jump ring, each with its base metal and its own lead status.

Six. Marking method and wording, with no “gold” or “silver” claim on a plated brass piece.

Seven. Packing: anti-tarnish bag, care card text, and a drop test on the packed carton.

Questions Buyers Ask

Does brass jewelry turn skin green?

It can. The mark comes from copper salts rather than from an allergy, and it shows most on a warm, damp hand.

Is brass jewelry safe to wear?

The alloy is the easy part. Lead in findings and worn plating are the parts that need a test, and both are asked for on paper.

Is brass the same as gold?

No. A gold-coloured brass piece has the colour and none of the metal, and calling it gold on a label is a claim a buyer should never sign.

Can a brass piece be re-plated?

A workshop can strip and re-plate it. At retail prices the cost rarely makes sense, so the finish has to be right the first time.

Is brass heavier than silver?

No. Brass sits lower on density, so the same shape is lighter in brass and feels warmer in the hand.

Why did my brass ring turn black?

Sulphur in the air, plus moisture. A soft cloth brings the colour back, and a sealed bag slows the next round.

BASE METAL

Send me the drawing and the price. I will ask the factory for the alloy split, the lead figure per part and the plating thickness at the edge. Three answers decide whether the quote is real, and all three cost nothing to request.

Send The Drawing

Questions & Comments

We read every one and reply within 24 hours

Brass questions usually start with a colour and end with a test report. Tell me whether the piece touches skin, and I will say which of the two matters more for that part.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x