Chain Types Jewelry: Link Names And Cost
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Chain Types Jewelry: Link Names And What They Cost

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 16, 2026 · 11 min read

A chain type is a link shape plus the way each link is joined, and that pair decides the machine, the labour and the price.

Two chains can look alike on a card and differ by a factor of three at the counter. The width printed on the tag says nothing about either one.

This guide names the families that cover most orders and gives each one a rule you can check with your fingers. It then shows where the cost sits.

Silver cable chain coiled on a beige studio surface beside two loose oval links
The same metal, three times the labour. What changes between these is how the links are joined.

The Name Is A Geometry Rule

Lay a chain flat on a table and look at one link. Its shape, and how the next link passes through it, gives you the family name.

That is the whole naming system. It is not a brand, a country or a finish.

Two terms sit underneath the names. The link is one loop of wire. The joint is where that loop closes, and it may be soldered or left open.

A soldered joint cannot open. An open joint can, which is why some cheap chains fail at the joint and not at the metal.

Once you know the family and the joint, three things follow: the machine that makes it, the labour per centimetre, and the way it fails.

The Families That Cover Most Orders

Six groups come up in almost every brief. Learn these and the trade names become variations, not new problems. The names below follow the common style list used across the trade.

FamilyThe rule that identifies itHow it is madeHow it fails
Cable (anchor, trace)Oval links of round wire, each turned 90 degrees from the lastAutomatic machine, open or solderedStretches when the wire is thin
Curb (Cuban)Links sit twisted, so the chain lies flat on its faceMachine, then flattened and often facetedTwists out of flat if a link opens
Box (Venetian)Square or rectangular links stacked like a tubeMachine, tight link spacingKinks and holds the bend
RopeTwo strands spiralled together, links not fully closedMachine, high link count per cmOne open link lets the run unravel
Spiga (wheat)A V pattern, each link passing through four othersMachine, tight and rigidUnlikely to break; resists stretching
ByzantineEach link threads through four others, reading as a weaveHand or slow machine assemblyCost, not strength, is the limit

Everything else sits inside a group. Figaro is a curb chain with one long link after three short ones. Singapore is a twisted curb with a natural curve.

Snake is a tight link stack with a round or square section. Brick is pressed until the links almost fuse into a band.

That is why a buying sheet that lists only “cable”, “curb” and “rope” still covers a long catalogue. The rest are named variants of the same three rules.

The Four Numbers On A Chain Line

A quotation that gives one number cannot be compared with another quotation. Four numbers make it comparable, and all four cost money.

NumberWhat it measuresWhere it moves the price
Link width, mmThe outside width of one link, which is the width on the tagMetal volume, and which machine can run it
Wire gauge, mmThe diameter of the wire the link is made fromMetal cost and tensile strength, almost linearly
Links per cmHow many links sit in one centimetre of finished chainLabour, soldering points, and how the chain drapes
JointSoldered, open, or soldered at the ends onlyHeat and handling time per link

Link width and wire gauge are not the same thing, and this is the most common mix-up in a brief. A 2 mm box chain and a 2 mm rope chain share a width and nothing else.

Links per cm is the number buyers forget. It is also the closest thing to a labour meter, because every extra link is another cut, another bend and often another solder point.

Ask for all four on the sample sheet. A supplier who can quote them is working from a spec, not from a photograph.

What One Metre Holds

Before labour, a chain is metal, and metal is geometry. Work out the volume first and the weight follows from whatever alloy you name.

Round wire is simple. Take the radius in centimetres, square it, multiply by 3.14, then multiply by the length in centimetres.

One metre of 1.0 mm wire holds about 0.79 cubic centimetres. At 1.5 mm it holds 1.77, and at 2.0 mm it holds 3.14.

Read those three numbers again, because they carry the whole weight argument. Doubling the wire diameter multiplies the metal by four.

Bar chart of metal volume in one metre of round wire at 1.0, 1.5 and 2.0 millimetres
Volume of metal in one metre of round wire. The jump from 1.0 to 2.0 mm is four times the metal, not two.

A finished chain is not a straight metre of wire, and two effects pull in opposite directions. Each link is a loop, so the wire in a metre of chain is longer than a metre. The overlap at every joint takes some of it back.

The honest method is to count. Measure the wire in one link, count the links per centimetre, and multiply.

Hollow chain is the third case, and it is where quotes part company. A hollow link is formed from thin strip, so it carries the width of a heavy chain with far less metal.

It also dents. A hollow rope looks like a heavy chain and wears like a light one. That is fine if the price and the promise agree.

On alloy, sterling is 92.5 percent silver by weight, with the balance usually copper. That 7.5 percent is part of the metal bill, and it is part of the colour.

The necklace programme is where most of this arithmetic lands, because a 45 cm chain multiplies every gram decision by a run of thousands.

The Cost Unit Is The Link

Four labour paths sit between a coil of wire and a finished chain. Each family uses a different mix of them, and that mix is the quote.

Linking. Cable, curb, box and rope run off automatic chain machines. The machine is set once, then it makes links at a steady rate.

Byzantine does not run that way. Each link threads through four others, so the assembly is slow per centimetre and the cost sits in hands, not in metal.

Soldering. A soldered joint costs heat, flux and handling. Some factories solder every link, some solder only the two ends, and both are called the same name on a tag.

This is the first line to ask about. It changes the price per centimetre and it changes what happens when the chain snags.

Flattening and faceting. A curb chain is pressed flat after linking. Diamond cutting then grinds one or two faces of every link, which adds a step per link and a bright edge that catches light.

Finishing. Polishing runs in a barrel by weight. Plating adds a layer measured in microns, and a thicker layer costs time in the bath as well as metal.

The plating route decides how the colour survives, and it belongs on the same sheet as the link spec.

Two components are bought, not made: the clasp and the end caps. They are quoted per piece, so they scale with the number of chains and not with their length.

Length then behaves in a simple way. A 60 cm chain uses a third more links than a 45 cm chain in the same style. The labour line rises with it, and the clasp line stays flat.

Where A Chain Breaks

Chains fail in a fixed order. The clasp gives first, then a joint, and the wire itself last.

That order matters because the fixes cost different amounts. A stronger clasp is a component change. A stronger joint is a process change, which is cheaper than it sounds and rarely offered.

Three step ladder showing clasp first, joint second and wire last as the failure points of a chain
Where the load stops. The clasp is a bought part, the joint is a process, and the wire is the last thing to give.

Rope chain has one behaviour worth knowing before you buy it. Its links are not fully closed, so one link that opens can let the neighbouring links slip in turn.

Spiga behaves the opposite way. Each link passes through four others, which is why it resists stretching and rarely snags on a knit.

Wire gauge is the quiet variable. Strength follows the cross-section, so 1.0 mm to 1.2 mm is a 44 percent gain in metal area and a real gain in pull.

Ask for a pull figure on the clasp and the joint, not on the wire. A test report that lists only the wire has tested the part that fails last.

What To Weigh And Count On Arrival

A chain is one of the few jewellery parts you can audit with a kitchen scale and a ruler. Three checks take ten minutes a carton.

Weigh one metre. Cut or ask for a metre length and weigh it against the quoted grams per metre. A shortfall of a few percent is usually the link count, not the alloy.

Count five centimetres. Lay out five centimetres on a ruler and count the links. Multiply by two for the links per ten centimetres, and compare with the approved sample.

A chain that arrives with fewer links per centimetre looks thinner and drapes differently, even at the same width and the same weight.

Look at the joint. A soldered joint shows a small fillet of solder at the seam under a loupe. An open joint shows a clean gap that will part under a pull.

Check the ends first. A factory that solders only the two end links does it for a reason, and that reason is time.

Two more things belong in the inspection note. The clasp should carry the stamp the order asked for. The plating should be even at the link edges, where the barrel throws the least metal.

If a carton fails the count, the fix is a rework or a credit. Both are easier to argue with a photograph of five centimetres on a ruler.

Nickel Is A Release Rate, Not A Ban

The claim that gets argued over in every chain order is the nickel one, and it is usually written the wrong way.

EU law does not ban nickel in jewellery. Annex XVII, entry 27 limits how much nickel comes off the part that touches skin.

The limit is 0.5 micrograms per square centimetre per week for prolonged contact. For a post through a piercing it tightens to 0.2.

The test is EN 1811, and it reports a release rate over a week of simulated wear. That is a different question from what the alloy contains.

This is why a supplier can be honest and still lose the argument. A brass base with a thin plate may pass on a pendant and fail on a clasp edge. That is where the plate wears through.

So ask for a release report on the finished chain, from a lab that names the method. A statement that the wire is nickel free answers nothing about the clasp.

Two more claims belong on the same sheet. Sterling silver is 92.5 percent silver by weight, and that figure is what a hallmark asserts. Plating thickness is quoted in microns, and it is the number that predicts how long the colour lasts.

The bracelet line feels this first, because a wrist rubs the clasp against a desk all day.

Six Lines For The Order

A drawing that says “rope chain, 2 mm, silver” leaves the three costliest decisions open. Six lines close them.

Line 1, family and variant. Write curb, and say open curb or closed curb. Write Figaro, and say how many short links sit between the long ones.

Line 2, two dimensions. Link width in mm and wire gauge in mm. Both, on the same line, because one without the other is not a spec.

Line 3, link density. Links per centimetre, with a tolerance. This is the line that predicts labour and drape.

Line 4, the joint. Every link soldered, ends only, or left open. Say which, and say where.

Line 5, finish and claim. Polish or diamond cut, then the plating route and its thickness in microns, then the nickel release report to EN 1811.

Line 6, the ends. Clasp type, end cap type, and a pull figure for the clasp and the joint.

Those six lines fit on one page, and they are enough for a factory to price without guessing. They are also enough to reject a carton that arrives with a different link count.

Some brands sell the chain on its own, not inside a finished piece. The same six lines work on a dropship route with a smaller first order.

LINK CHECK

If a chain sample is on your desk, send the family name, the width, the wire gauge and the link count per centimetre. I will check the four numbers against the price you were given and tell you which line the factory left out.

Send The Sample Sheet

Questions Buyers Ask

Is a Cuban chain a curb chain?

Yes. Cuban is the trade name for a close-linked curb. The rule is the same: the links sit twisted, so the chain lies flat.

Does 2 mm mean the wire?

No. The 2 mm on a tag is the outside width of one link. The wire gauge is a separate number, and it is the one that sets weight and strength.

Which chain type is strongest?

Spiga is the usual answer, because each link passes through four others. It resists stretching and rarely snags, and it is stiffer than a cable.

Why does Byzantine cost more?

Each link threads through four others, so it cannot run at cable speed. The cost sits in assembly time rather than in metal.

Can I print nickel free on the box?

The EU rule limits release, not content: 0.5 micrograms per square centimetre per week. A clean release report is the claim you can defend.

How many links are in a 45 cm chain?

Multiply the length by the link count per centimetre. At four links per centimetre that is 180 links, and every one of them is a joint.

Questions & Comments

We read every one and reply within 24 hours

Which link family did the sample come from, and how many links sit in a centimetre? Send the width, the wire gauge and the link count, and I will say where the price difference comes from.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x