What Is PCBA: A Board, Its Parts and Four Files
PCBA means the bare board plus the parts. The three letters add one word to a PCB, and a factory to the supply chain.
A PCB is fibreglass, copper and a printed pattern. It carries current between points and nothing else.
A PCBA is that same board with components placed, soldered and tested. It is a working assembly rather than a substrate.
The difference decides who you buy from, what a quotation covers, and which of four files you have to send.
The Short Answer
PCBA stands for printed circuit board assembly. It is the board after the parts have been mounted and the joints have been made.
In the trade, a PCB is bought from a board house and a PCBA is bought from an assembly house. Sometimes one company does both.
That is why two quotations for “the board” can differ by a factor without either supplier being dishonest. One is quoting the fibreglass and the other is quoting the product.
The assembly house also takes on the parts. It buys them, or you consign them, and the choice changes both the price and who carries the risk.
Everything else in this article follows from that split.
What the Bare Board Already Contains
Even the empty version has four layers of work in it, stacked. Knowing them helps when a factory asks which file covers what.
The substrate is the structural base. FR4 glass-epoxy is the ordinary choice; flexible and metal-core versions exist for bends and for heat.
Copper is etched into the pattern that carries current. It is what makes a board a circuit rather than a plate.
The solder mask is the green layer that covers the copper everywhere solder must not land. It keeps a joint from becoming a short.
The silkscreen is the white printing: reference numbers and outlines. It is for the human who has to find a part later.
None of that changes when components are added. The mask openings are where the paste will go, and the copper underneath decides where the joint belongs.
The assembly house therefore reads the bare board as a set of instructions. Get the mask or the pad geometry wrong and the line finds out.
The Line, in Six Steps
Before any of it starts, one check runs. The factory reads your design for manufacturability and reports what cannot be built as drawn.
The order below follows an assembly house’s own process guide, which is the clearest public description of the line.
That check is the cheapest part of the project. A pad that is too close to its neighbour is a short that repeats on every board.
One, paste. A stainless steel stencil is laid over the board and solder paste is squeegeed through the openings onto the pads.
Two, place. A pick-and-place machine lifts each part from a reel and drops it onto the paste, at coordinates taken from a file.
Three, reflow. The board passes through an oven that warms it, melts the paste, then cools it under control. The joint is made.
Four, look. Cameras compare each joint against a reference, and X-ray is used where the joint is hidden under a package.
Five, through-hole. Parts with leads go in by hand or through a wave of molten solder, which is why paste cannot do this job.
Six, test. Power and signals are applied, and the outputs are checked against limits somebody had to write down first.
Two-sided boards double most of it. The side with fewer and smaller parts is printed, placed and reflowed first, then the board is turned and the cycle repeats.
Why Paste and Not Solder Wire
A hand with an iron can join two things. A machine cannot, so the process was rebuilt around a material that can be printed.
Solder paste is metal powder held in flux. An ordinary lead-free mix runs about ninety-six parts tin to three of silver and half a part of copper.
The flux does the chemistry: it cleans the surface and helps the alloy wet it. The metal does the joining once the oven is hot enough.
Reflow peaks near 250 °C, and the climb is deliberate. A board that goes straight to that temperature warps and shocks its parts.
Then surface tension does free work. If the pads are sized properly, molten solder pulls a part into alignment by itself, which forgives a small placement error.
That is the whole reason this method took over, as the reference on surface-mount work sets out. It is not that paste is better than wire; it is that paste can be printed in the same place, to the same thickness, ten thousand times.
The Four Files a Factory Needs
An assembly house cannot start from a picture. Four documents cover the four things it has to do, and each one has a failure it prevents.
The list below is built from the process rather than quoted from a standard: every step needs an input, and these are the inputs.
| File | What it feeds | What goes wrong without it |
|---|---|---|
| Bill of materials | Buying and kitting the parts | A wrong value or package is fitted, and the board works badly |
| Fabrication data | The board, the mask openings and the stencil | Paste lands in the wrong place, or the stencil is cut wrong |
| Centroid file | Machine coordinates, rotation and side | Parts are mirrored, rotated or placed on the wrong face |
| Assembly drawing and test spec | Orientation, no-fit parts, pass limits | A diode goes in backwards and “tested” means nothing |
The first file carries the most risk. A bill of materials without manufacturer part numbers invites equivalents, and an equivalent is a decision the buyer should make rather than the line.
The third file is the one most often missing. Design software can export it, but only if somebody remembers, and a hand-written coordinate list drifts as soon as the layout changes.
The fourth is the one that decides what “tested” means. Without a written limit, a functional test is a person watching a board and hoping.
Send all four together. A factory that receives three will start work and ask for the fourth when the line is already set up.
Version control is the fifth thing nobody lists. Two revisions can share a file name and differ in one pad, and the factory builds the file it was given rather than the one in your head.
What “Tested” Can Mean
Four different checks get sold under one word. They look at different things, and each one is blind to something the others see.
| Check | What it looks at | What it cannot see |
|---|---|---|
| Optical inspection | The shape and position of every visible joint | Anything under a package |
| X-ray | Hidden joints, voids and alignment | Whether the circuit works |
| In-circuit test | Continuity and value, through probes on test points | Boards with no room for probes |
| Functional test | The product doing its job, against written limits | Why a failure happened |
Optical inspection is the default and it is fast. Cameras catch a missing part, a tombstoned chip or a bridge long before a person would.
X-ray earns its place where the joint is under the body: a ball grid array or a package with a thermal pad. The failure it catches is invisible from outside.
In-circuit test needs access. It puts probes on the board and measures values part by part, which is why designs with no test points cannot use it.
Functional test is the one a buyer actually cares about, and it is only as good as its limits. Somebody has to state the voltage, current and signal range that counts as a pass. By then the batch has usually been built.
Rework is the quiet cost behind all of them. A board that fails a check is repaired by hand or scrapped, and a repair is a person with an iron and a hot-air tool working under a microscope.
Ask which of the four a quotation includes. A price that says “tested” without naming them is a price for optical inspection and a conversation later.
What a Quote Covers, and What It Hides
Two quotations for the same board can differ by a third and both be honest. The gap is usually in five places.
One-off tooling. The stencil, the test fixture and the programming jig are paid once. A quotation that omits them is not cheaper, it is incomplete.
Who buys the parts. In a turnkey order the factory sources and carries the risk. In a consigned order you ship the parts, and a shortage becomes your problem on the day.
Part authenticity. A turnkey quote built on the cheapest available parts and one built on authorised stock are different products at the same board count.
Scrap allowance. Every run loses a few boards. Whether that is charged, absorbed or quietly added to the quantity is worth reading before the second order rather than after.
Test scope. The fourth check in the table above costs more than the first. A quote that names only one of them has answered a different question.
Lead time follows the parts rather than the board. A common resistor arrives in days, while one specific microcontroller can set the delivery date for the entire order.
None of this is sharp practice. It is what a price looks like when the scope was never written down, which is why the order lines below matter more than the number.
Wash, No-Clean and Coating
After soldering, the board is dirty. Flux residue sits around the joints, and a hand has been on the surface.
That residue is not cosmetic. Left for months it turns sticky and slightly acidic, and it can work at a joint over time.
The usual wash is deionised water with an air blast to dry. Deionised matters because it is the ions in ordinary water that attack a circuit, not the water.
Many modern processes skip the wash instead. A no-clean flux is designed to be left in place, which saves a step and a tank.
Two cases still call for cleaning: a board that will be coated, and a board running at high frequency. Residue spoils adhesion in the first and the signal in the second.
So the coating decision and the wash decision belong in the same conversation. Ordering a conformal coat on a no-clean board is a way to buy a warranty claim.
Six Lines for the Order
Put the deliverables in the order, not just the price. These six sentences are what makes a first article approval mean something.
One. List the four files by name and version, and state that the build follows that revision.
Two. Say who buys the parts, and whether equivalents are allowed without written approval.
Three. Name the tests included, and give the pass limits for the functional one in writing.
Four. State the wash and coating decision, and the standard the assembly is judged against.
Five. Fix the first-article process: what is submitted, and who signs it off before volume.
Six. Record the tooling you paid for, and that the stencil and fixture are yours to move.
The fifth line is the one that stops a bad batch. A first article that is approved in writing, with photographs, is the only cheap insurance in this process.
The assembly is judged against a published standard, and the acceptability standard a buyer can cite is the one to name in the order rather than leave to the factory.
For a comparison across suppliers, the answers need to line up. The same sheet across every supplier does that better than four quotations in four formats.
Before the order grows, look at what is on the market. The counters where boards and parts are sold side by side show how much of a finished product is bought rather than built.
None of that replaces a look at the line. A line audit that covers the solder shop should include the oven profile and the residue on a finished board.
Boards also cross borders with paperwork. The file that clears the goods at the border is separate from the four design files above.
Send me the four files you were asked to prepare, or the quotation you received. I will say which document is missing, which tests the price covers, and where the scope stops before the parts are bought. I will also flag any file that looks out of date with the drawing. No cost, no obligation.
Check My PackageQuestions Buyers Ask
Is PCBA the same as PCB?
No. A PCB is the bare board with copper traces and no parts. A PCBA is that board with the components placed, soldered and tested.
What files do I need to send for assembly?
Four: a bill of materials, the fabrication data, a centroid file for the placement machine, and an assembly drawing with the test limits.
What does turnkey mean?
The factory buys the components as well as assembling the board. In a consigned order you supply the parts and the factory only places and solders them.
Why does a quote not include testing?
Because “testing” ranges from a camera check to a full functional run with a fixture. The fixture and the time are real costs, so they are quoted separately.
Should the boards be washed?
Often not, if the process is no-clean. Clean when the board will be coated or runs at high frequency, because residue spoils adhesion and signal.
Can the factory substitute a part that is out of stock?
Only if you allow it in writing. An equivalent part is a design decision, and the person making it should be the one who owns the schematic.
Questions & Comments
We read every one and reply within 24 hoursIf a quotation came back without a test line or a file list, send it over. The scope is usually what is missing, not the price.