What Is Depth of Discharge: The Number Behind a Cycle Count
A cycle count without a depth is a number without a unit.
Depth of discharge, usually shortened to DoD, is how much of a battery’s stored energy has been taken out. Empty the pack completely and the depth is 100 %. Take a tenth and it is 10 %.
It is the mirror of state of charge. One rises as the other falls, and the two always add up to 100 %.
That definition is simple. What follows is not, because a battery’s life depends on this number far more than on the calendar.
The Short Answer
DoD is a percentage of capacity used. State of charge is what is left. So DoD plus SoC equals 100 %.
The number matters because cycling a battery deep does more damage than cycling it shallow. Every cycle consumes part of the life, and a deep cycle consumes more.
That is why a spec sheet often quotes a cycle count that looks enormous. The count usually assumes a depth well short of empty, and the depth is where the honesty lives.
Two terms keep coming up, and they are not the same. A cycle is a discharge and the charge that follows. A depth is how far that discharge went.
What a Cycle Count Assumes
A published figure of 3,000 cycles sounds like a promise. It is really a measurement with two conditions attached, and a quote rarely states either one.
The first is where life ends. In the published test data, the count stops when capacity falls to 70 % of its original value. A pack at 69 % is counted as finished, even though it still works.
The second is how deep each cycle went. The same source notes that makers often specify cycle life at an 80 % depth. A real battery keeps a reserve before the next charge.
Change either condition and the number moves. A pack rated 3,000 cycles at 40 % depth is a different product from one rated 3,000 at 80 %. Both labels look the same.
There is a third weakness, and the source says it plainly. Counting cycles is not conclusive on its own, because there is no single agreed definition of what counts as a full cycle. A thousand small discharges can add up to one, or to several.
So the practical rule is to ask for three things together. The cycle count, the depth it was measured at, and the capacity level that defines the end.
The Numbers, Side by Side
One published table does most of the work here. It lists discharge cycles against depth, for two common lithium chemistries, ending at 70 % of original capacity.
| Depth of discharge | NMC cycles | LiFePO4 cycles |
|---|---|---|
| 100 % | ~300 | ~600 |
| 80 % | ~400 | ~900 |
| 60 % | ~600 | ~1,500 |
| 40 % | ~1,000 | ~3,000 |
| 20 % | ~2,000 | ~9,000 |
| 10 % | ~6,000 | ~15,000 |
Read the first row and the last row together. A cobalt blend cycled to empty gives about 300 cycles. The same chemistry cycled to a tenth gives about 6,000.
That is a twentyfold difference from one design decision. It is also why two packs of the same size can carry wildly different warranty terms.
The gap between the two columns is worth a moment. Iron phosphate gives roughly twice the cycles of a cobalt blend at every depth in the table. At the shallow end the gap is three times.
That is not a small difference in the same product class. It is the reason some packs are sold on cycle count and others on energy per kilo.
The trade runs the other way on energy. A cobalt blend stores more per kilo, which is why phones use it and stationary storage often does not.
So a fair comparison picks one column and stays in it. Mixing a cobalt cycle count with an iron phosphate energy figure produces a product that does not exist.
One warning belongs with the table. The source states that its figures describe cobalt-based cells. Iron phosphate and titanate cells run at lower voltages, so the voltage references in the same document do not carry across.
Shallow Is Not Automatically Better
Here is the part that flips the usual advice. More cycles do not always mean more energy delivered over the life of the pack.
The same source compares four cycling windows, and each one trades depth against total output.
| Window | Cycles | Energy delivered |
|---|---|---|
| 75 % to 65 % state of charge | Longest life | 90,000 units, using 10 % of the pack |
| 75 % to 25 % | About 3,000 | 150,000 units, using 50 % |
| 85 % to 25 % | About 2,000 | 120,000 units, using 60 % |
| 100 % to 25 % | Short | Long runtime, heavy wear |
A pack used only across a tenth of its range lives the longest. It also delivers the least energy in total, because it is barely working.
The middle window wins on total output. Three thousand cycles at half depth beats an enormous cycle count at a tenth of the range.
That is why an electric vehicle limits itself to roughly 85 % on the way in and 25 % on the way out. The published note puts that at about 60 % of the nameplate energy, and calls it a deliberate trade.
The cost appears in the specification. A pack rated at 250 Wh per kilo, run in that window, behaves like 150 Wh per kilo in daily use. You are carrying weight you rarely touch.
So the honest question is not “what depth is right”. It is “how much energy do I need per cycle, and how many cycles do I need in total”. Those two numbers set the depth.
Two duty cycles make the difference plain. A phone is emptied most days and replaced every few years, so it is a deep-cycle product. An electric car is held between two mid-range charge levels by design, so it is a shallow-cycle product with a large pack.
Same cells in both. Different depth, different service life, different cost.
Heat and a Full Charge Do Their Own Damage
Depth is only one of the levers, and possibly not the strongest. The same document is blunt about the other two.
Keeping a battery at a high charge, in a warm place, can do more harm than cycling it. The published figures compare storage for a year at different temperatures and two charge levels.
| Storage temperature | Stored at 40 % charge | Stored at 100 % charge |
|---|---|---|
| 0 °C | 98 % left after a year | 94 % left after a year |
| 25 °C | 96 % | 80 % |
| 40 °C | 85 % | 65 % |
| 60 °C | 75 % | 60 % after three months |
Read the bottom right corner. A fully charged pack stored at 60 °C loses 40 % of its capacity in three months, without a single cycle.
Compare it with the top left. The same pack, left half charged in a cold room, keeps almost everything for a year.
For a product that sits in a warehouse or a hot vehicle, that table matters more than the cycling rules. A conservative depth will not save a pack that spends its life full and hot.
One number marks the line in the source. Above 30 °C counts as elevated, and above 4.10 V per cell counts as a high charge. Both are easy to check on a real product.
Lead-Acid Plays by Other Rules
Most of the numbers above describe lithium. Sealed lead-acid behaves in the same direction, with less tolerance and a different curve.
A maker’s technical note puts it plainly. Repeated discharges to 80 % or 100 % shorten the life of a sealed lead-acid block. The charging profile has to match the block type as well.
The practical guidance that follows is a floor rather than a curve. Keep a lead-acid pack well above half empty, and treat anything below that as an occasional event, not a daily habit.
The reason is mechanical as well as chemical. A deep discharge on lead-acid leads to sulphate forming on the plates, and that material does not come back on the next charge.
So a comparison between two packs is only fair if the two are the same chemistry. A depth figure borrowed from a lithium sheet says nothing useful about a lead block.
Usable Capacity Is Not Nameplate Capacity
A pack’s label gives the total it holds. The depth decides how much of that total you are allowed to use, and the two numbers are often confused in a quote.
Take a 100 Ah block. At a depth of 80 % it gives 80 Ah per cycle. At 50 % it gives 50, and at 20 % it gives 20.
In energy terms, a 12 V 100 Ah block carries 1.2 kWh on its label. At 80 % depth the usable part is 0.96 kWh, before round-trip loss is taken out.
So a larger pack run shallow can deliver the same usable energy as a smaller pack run deep, and last longer doing it. That is the whole design argument in one sentence.
The trade is weight and cost. A pack sized for 50 % depth is roughly twice the cells of one sized for 100 %, and it carries twice the price.
Two corrections sit above that sum. Round-trip losses mean less energy comes out than went in, and the end-of-life figure cuts the usable amount again as the pack ages.
The practical sum therefore has four steps. Required energy per cycle, divided by the depth you allow, gives the nameplate size. Then add the loss, then add the ageing margin.
Written that way, a depth choice stops being a preference and becomes a sizing input. It changes the bill of materials, the weight and the price at the same time.
What a Warranty Is Really Saying
A warranty term is a depth figure in disguise. Reading it that way settles most arguments before they start.
Take a pack sold as 3,000 cycles. The seller has to define two things to make that number checkable. When the pack is judged finished, and how deep each cycle went.
Published data uses 70 % of original capacity as the finish line. Below that, the pack still runs, but it no longer meets the spec it was sold on.
Most makers then test at 80 % depth, because a real product keeps a reserve. So the headline figure quietly carries both assumptions.
A warranty that names neither one is not a stronger promise. It is a weaker one, because the seller chooses the test after the claim arrives.
Three questions fix that. What depth, what end capacity, and which test method. A seller who can answer all three has measured something.
Six Lines for the Order
Most battery orders name a capacity. Six lines make the depth explicit, and they fit the same one sheet for the whole build.
One. Name the chemistry, the nameplate capacity and the voltage printed on the label.
Two. State the energy required per cycle, so the depth can be derived rather than guessed.
Three. Give the cycle count together with its depth and its end-of-life capacity.
Four. State the temperature range the pack will live in, and the charge level it will be stored at.
Five. Name the cut-offs in the protection board that enforce the depth in daily use.
Six. Ask for the test method behind the cycle figure, since two labs can count a cycle differently.
The cell itself has its own questions. How the two lithium packages differ is set out in how the two packages differ. Where the pack is charged from a panel, the solar controller comparison covers how the charge arrives. A backup unit carries its own assumptions, set out in what a backup unit assumes.
Send me the battery line from your drawing or the datasheet you were given. I will work out the usable energy at the stated depth, check whether the cycle count carries its two assumptions, and say which of the six lines is still missing. No cost, no obligation.
Check My PackQuestions Buyers Ask
Is a 100 % depth of discharge bad for lithium?
It is the hardest case in the published tables. A cobalt blend cycled to empty reaches about 300 cycles, against roughly a thousand at 40 % depth.
What depth should I design for?
There is no single figure. The honest answer comes from two numbers: the energy you need per cycle and the total number of cycles you need. Together they set the depth and the pack size.
Does depth change the usable capacity?
Yes, directly. A 100 Ah pack at 80 % depth gives 80 Ah per cycle. At 50 % it gives 50. The nameplate stays the same and the usable amount does not.
Is 50 % depth twice the life of 100 %?
More than that, going by the published table. The count rises from about 300 at full depth to about a thousand at 40 %, so roughly three times rather than twice.
Does it matter how I store a battery?
A great deal. One table shows a full pack kept at 60 °C losing 40 % of its capacity in three months, with no cycling at all. Charge level and heat can outweigh depth.
Do the same numbers apply to lead-acid?
Not the numbers, only the direction. Repeated deep discharges shorten a sealed lead-acid block too, and the usual guidance is to stay well above half empty.
Questions & Comments
We read every one and reply within 24 hoursIf the datasheet says 3,000 cycles and stops there, send me the line. I will ask what depth and what end-of-life capacity it assumes.