Hammock Types: Five Shapes and How Each One Fails
Home
Yiwu, Zhejiang, China
Mon – Fri 9:00 AM – 6:00 PM · Sat 9:00 AM – 4:00 PM
[email protected]

Hammock Types: Five Shapes and What Each One Is Bad At

Alan Xiao, Founder of Sourcing Pioneer
Alan Xiao Founder of Sourcing Pioneer
· Updated November 3, 2026 · 10 min read

Most pages on hammock types show five photos and no anchor count. Shape is the part that decides how you lie, how much it weighs, and how it will fail.

A hammock is a piece of fabric held between points. Everything else is a choice about where those points go and how the fabric is cut.

Warm beige studio still life of a folded olive ripstop hammock in its stuff sack beside a coiled brown webbing tree strap
Folded bed, coiled strap, one stuff sack. The shape is decided before either is cut.

Five Shapes and What Each Is Bad At

Buyers and brands use five shape names. Each one carries a hidden cost, and the cost is different for every shape.

Gathered-end. A rectangle of fabric bunched at both short ends and hung from two points. It is the cheapest shape to make and the most common on the market. The fabric hangs in a curve, and you lie across it on a slight diagonal. The centre of gravity sits low, so it does not tip.

Spreader bar. Bars at the head and foot hold the fabric open, which gives a flat, wide surface and easy entry. The bars also lift the centre of gravity, so the bed is easy to tip. The hardware adds weight, and the bars are the part that breaks.

A single bar at one end only is more stable. A version with three attachment points, one at each corner of the bar and one at the plain end, is close to untippable.

Bridge. Spreader bars again, but the fabric is cut like a suspension bridge. You get a flat lay from head to foot instead of a diagonal. The cut can squeeze the shoulders, and the shape is heavier than a gathered-end bed.

Single-point. One anchor above, so the bed hangs like a chair and turns with you. It solves the tree spacing problem and creates a spinning problem.

Multi-point. Three or more anchors spread over an area, which turns the bed into a platform for two or more people. This is the heaviest and most loaded shape on the list, and it needs trees that can take the pull.

ShapeAnchorsHow you lieWhere it goes wrong
Gathered-end2 pointsCurved, on a diagonalBeds that are too short
Spreader bar2 pointsFlat and wideTipping, bar joints
Bridge2 pointsFlat, head to footShoulder squeeze, weight
Single-point1 pointSwivel chairRotation
Multi-point3 or morePlatform for twoTree spacing, total load
Panel comparing five hammock shapes by anchor count, lay and the failure each one is prone to
Five shapes, and the failure each one is known for.

Two more words matter inside every shape. An open hammock has no net. A jungle hammock carries a bug net and often a ridge line over the head.

Open beds suit a garden, a park or a living room. Jungle beds suit camping, because a net over the face is the difference between a night of sleep and a night of slapping.

Single, Double, Triple: Width, Not People

These three words describe the width of the fabric. They do not describe how many people the bed holds.

Most brands cut single, double and triple from the same fabric with the same stitching, so all three carry the same weight limit. The double is wider. That is the whole difference.

The numbers behind the words are published. A one-person bed is usually rated for 250 to 350 pounds, or 110 to 160 kilograms. A two or three-person bed runs from 400 to 600 pounds, or 180 to 270 kilograms.

A retailer’s buying guide gives a wider spread for the market as a whole. Beds there support 150 to 500 pounds, and the fabric widths run from 4 feet to 9 feet.

Read those two ranges together and a problem appears. A bed sold as a double can carry a 150 pound rating, and a bed sold as a single can carry 350.

The word on the box tells you the width. Only the capacity line tells you the load, and that line is the one to quote in an order.

The Numbers a Listing Gives You

A hammock listing carries four numbers, and each one is easy to state in a way that hides the real product.

Length and width, measured flat. Published ranges for unslung beds run from 3 feet across to 14 feet, and from 6 feet long to 11 feet. The wide end of the range is multi-point and family beds, not a camping bed.

Bed width alone. A retailer’s own guide puts bed widths between 4 feet and 9 feet. The wider beds can seat up to four people, and the narrow ones should take one or two.

Pack weight. The suspension set alone runs from 7 ounces to several pounds. The bed is listed apart, and the two figures are often mixed in a single number on a marketplace page.

Capacity. The figure should say static, because static is what it measures. A person stepping in adds a shock load that no hammock is rated for, and a jump is worse.

A stand carries a capacity of its own. One buying guide sets 450 pounds as the limit for a stand, which can sit below the rating of the bed it holds.

Those four numbers become the first half of a sheet a hammock factory can quote on. A quote that answers a colour and a price has skipped all four.

The Hang: Angle, Distance, Height, Trunk

A hammock is comfortable or not because of how it is hung, and four measurements decide that.

About 30 degrees. The usual starting point for the angle of each attaching line. A flatter hang pulls much harder on both anchors, and a steeper one folds the fabric around you.

Two thirds of the bed length. Without spreader bars, the posts or trees should stand about two thirds of the hammock’s length apart. Hang it between points that are closer, and the bed has to go higher to keep the fabric off the ground.

18 to 24 inches. The clearance between the lowest point of an empty bed and the ground. That gap is what keeps a loaded bed from scraping soil, and it is measured before anyone gets in.

One foot of trunk. Healthy trees with trunks at least a foot across, so the tree can carry the load the bed is rated for. A thin tree with a wide angle is a broken tree and a dropped sleeper.

The same guide adds one rule that settles most claims. The capacity figure is a static weight. Do not jump in, and do not treat the rating as a test of the fabric’s patience.

This is why two hammocks that look the same in a photo can behave nothing alike. The shape sets the lay, and the hang sets the comfort. Neither is visible in a catalogue shot.

Fabric, Net and Stitching

Camping beds are cut from nylon parachute fabric, and many use a ripstop weave. The grid of heavier threads stops a small tear from running across the bed.

Nylon is light and strong for its weight, and it stretches. The stretch is comfortable under a body and awkward for a factory. A bed that creeps longer over a season reads as a defect to a buyer.

Jungle beds add three parts. A bug net over the face, pockets for a phone and a lamp, and a ridge line that holds the net away from the sleeper.

Some shapes add a slit for entry through the bottom of the bed. It is convenient. It is also a seam that has to be reinforced, because the entry point takes a hand and an elbow every night.

Suspension is sold apart on many camping beds. The usual part is a pair of webbing straps, often called tree huggers. They loop around the trunk and spread the load across the bark.

Strap width is the quiet specification. A narrow strap concentrates the same pull into a smaller band of bark, and parks and campsites have started to notice.

Every one of those parts is a line in the check on a shipped batch. Fabric weight, stitch density at the gathered end, strap width and net mesh are all measurable on a bench. None of them need a lab.

Weight per square yard is the number to ask for first. Two beds can look identical in a photo and differ by a third in fabric weight. That gap shows up as capacity, and as how long the bed lasts.

Where the Cheap Ones Fail

Six defects turn up again and again on incoming hammock batches. Each one is invisible in a product photo and cheap to prevent.

A light fabric with a heavy label. The capacity is printed on the box and the fabric weight is not. A bed cut from thin cloth can carry a high number for one season.

A single row of stitching at the gathered end. The whole load passes through that channel. Two rows with a bar tack at each corner is a small cost at the factory and the difference at year three.

A softwood spreader bar with a screw thread into the end grain. The screw pulls out under a rolling load. A through-bolt or a metal sleeve does not.

Straps sold apart. Many camping beds ship without them, and the buyer discovers it at the campsite. Say in the listing whether the straps are in the bag.

A decorative carabiner. Hardware sold for keys is not rated for a person’s weight. Ask for the rating figure, and accept nothing printed on the gate alone.

A capacity with no record. A number with no test behind it is a wish. One break test per batch, with the figure written on the sheet, turns the number into a claim.

Which Shape Sells Where

The shape follows the buyer, and the buyer follows the place the bed will hang.

Garden and patio. Spreader bar beds, often quilted, often sold with a stand. The buyer wants a flat seat and a photo-ready look, and is not walking anywhere with it.

Camping and hiking. Gathered-end jungle beds with a net and a ridge line. The buyer counts grams and wants the straps in the bag.

Indoor and decor. Woven cotton and rope beds in the Mayan and Brazilian styles, sold as furniture. The buyer is shopping for a room, not for a night outdoors.

Glamping and sites. Multi-point beds that hold two, hung between trees that were chosen for the job. These orders are small and the load questions are large.

A single factory rarely does all four well. Canvas and rope work sits in a different workshop from ripstop nylon and netting. A buyer spreading across all four is buying from four suppliers.

A Short History That Explains the Shapes

The word comes from the Taíno and Arawak word hamaka, which meant a stretch of cloth. Spanish colonists met the bed in the West Indies and took it to Europe.

Early beds were woven from tree bark, and later from sisal, which was more plentiful. In the Yucatán, Mayan weavers worked the bed on a loom. The quality of the result depended on the thread and the number of threads.

At sea the bed solved a different problem. The Royal Navy adopted the sling hammock in 1597. That year it ordered three hundred bolts of canvas for what the record calls hanging cabbons or beddes.

Sailors of that period used a spreader. It was a length of wood with a V cut in each end, and it held the strings apart. The first string was set tighter, so it raised a lip along each side. That piece of wood is the ancestor of the bar in a patio hammock.

The bed went on working where space was short. Troopships used hammocks in the Second World War, and from Apollo 12 onward the lunar module carried them so two men could sleep between moonwalks.

So the shapes are not a modern design exercise. A naval bed, a Mayan bed and a camping bed are three answers to three different rooms.

Six Lines for a Hammock Order

An order that can be checked is written in six lines. Each line is a figure or a named material. Each one is a place where two quotes match on price and differ on the product.

The shape and the anchor count. Gathered-end, bridge, spreader bar or multi-point, with the number of hanging points. The shape sets the pattern, the cut and the hardware.

The bed size, finished. Length and width with the tolerance. A bed quoted at 9 feet that arrives at 8 feet 6 inches is a different product on a shelf.

The fabric. Weight per square yard, ripstop or plain, and the fibre. This line decides the capacity and how long the bed holds it.

The suspension. Strap width, the hardware and whether either is in the bag. A bed without straps is a bed a customer cannot hang.

The capacity and the test. The static rating plus the test that produced it, with the number of samples per batch.

The batch and the stitch check. A traceable batch number and the seam spec at the gathered end, including rows and bar tacks.

LineExample of a stated valueWhat it protects
Shape, anchorsGathered-end, 2 pointsPattern and cut
Bed size9 ft 6 in by 4 ft 6 in, plus or minus 1 inThe fit on a shelf
Fabric1.9 oz ripstop nylonCapacity and life
Suspension1 in webbing straps, includedWhether it can hang
Capacity, test400 lb static, 3 samples per batchThe claim
Batch, stitchTraceable number, 2 rows plus bar tackClaims and returns

A capacity that fails on arrival is the classic hammock complaint. Then the claim route when a load test fails rests on the test record written on the sheet. It does not rest on an argument about how the bed was hung.

Hammocks are bulky and light, so the weight a full carton reports is usually set by volume, and not by the bed. A bed that compresses well cuts freight, and that saving is often larger than the unit price gap between two quotes.

Panel of six hammock specification lines from shape and anchors to batch and stitch check
Six lines, and the two that decide whether the bed can be hung and proved.

The five shape names and the anchor counts come from the entry on the hammock. So do the lay of each shape, the fabric practice and the 30 degree hang angle. The width meaning of single and double, the bridge cut and the shoulder squeeze come from a tester’s guide to hammock styles. The 150 to 500 pound range and the 4 to 9 foot widths come from a retailer’s buying guide. So do the 18 to 24 inch clearance, the one foot trunk and the 450 pound stand.

Questions Buyers Ask About Hammocks

What are the main types of hammock?

Five shapes: gathered-end, spreader bar, bridge, single-point and multi-point. Each is defined by how many points it hangs from and how the fabric is cut.

Does a double hammock hold two people?

Not by the name. Single, double and triple describe width. The load is set by the capacity figure, and a double bed can be rated for 150 pounds.

What hang angle should I use?

About 30 degrees on each attaching line is the usual starting point. A flatter hang pulls harder on the anchors and changes the shape of the bed.

How far apart should the trees be?

About two thirds of the hammock’s length when there are no spreader bars. Closer than that, the bed must hang higher to keep the fabric off the ground.

Are tree straps included with a camping hammock?

Often not. Many camping beds are sold with whoopie slings or rope only, so the listing should say whether webbing straps are in the bag.

What does the capacity figure mean?

A static load. It is measured with weight at rest, and it does not cover the shock of stepping in or jumping, which no bed is rated for.

The Short Version

Pick the shape from the place the bed will hang, and pick the size from the sleeper. Then settle the order on fabric weight and a tested capacity.

Everything else, from the colour to the stuff sack, is a choice you can change later. The shape and the fabric are the two you cannot.

FIVE SHAPES

Shape First, Then the Test

A hammock quote that names a colour and a price has skipped the fabric and the capacity. Send the shape, the bed size, the fabric weight and the load you need to prove. We will say which lines a sample can settle on a bench, and which one needs a break test before the first carton ships.

Send the Brief

Questions & Comments

We read every one and reply within 24 hours

Every hammock list shows five photos and none of them says how the bed is anchored. Tell us the job, and we will say which type and which test settle the order.

Subscribe
Notify of
guest
0 Comments
Most Voted
Newest Oldest
0
Would love your thoughts, please comment.x
()
x