Bench Press Width: The 81 cm Rule and the Grip That Fits You
Bench press width is usually taught as a feeling. It is really one measurement: the distance between your hands, checked against the width of your own shoulders.
This page gives the limit that competitions use, the three grips in plain numbers, and a way to measure yourself once so the guesswork stops.
The One Limit That Matters
In most powerlifting federations, the widest legal grip puts the hands 81 cm apart. That is the outer limit, and it works out to about 31.9 inches.
The figure is not arbitrary. The ring marks on a competition bar sit so that the index finger lands inside them, which is why the marks are there at all.
Research work describes grip widths as a share of the distance between the two points of the shoulder. A medium grip is 100% of that distance, and a wide grip is 200% of it.
That framing is useful because it turns a feeling into a ratio. A lifter with a narrow frame reaches the legal limit at a wider hand spacing, and a lifter with broad shoulders reaches it sooner.
| Grip | Width, as a ratio | Width, in numbers | What it asks |
|---|---|---|---|
| Close | under 100% of shoulder width | narrower than the shoulder points | More triceps, less chest |
| Medium | 100% of shoulder width | hands level with the shoulder points | The usual default |
| Wide | 200% of shoulder width | up to 81 cm, about 31.9 inches | Shorter stroke, more shoulder load |
Two numbers carry the whole table. The 81 cm cap is a rule, and 100% of shoulder width is a starting point. Everything between them is a trade.
Close, Medium, Wide and What Each One Changes
A study that measured muscle activity under three grips found the clearest difference in the biceps, of all places. The narrow grip showed 30.5% less biceps activity than the medium grip, and 25.9% less than the wide grip.
The measurement was taken during a five second isometric pause, with the bar held about one inch above the chest. That is a controlled test, so the numbers describe the pause, not a full rep.
What changes with width is the length of the stroke. A wide grip shortens the distance the bar travels, which is why more weight can move. A close grip lengthens the stroke and shifts work to the triceps.
The cost is in the shoulders. A very wide grip puts the upper arm further out from the body, and the shoulder joint takes more of the load at the bottom. That is why many lifters bench wide in a meet and narrower in training.
| Grip | Stroke length | Main drivers | Best use |
|---|---|---|---|
| Close | Longest | Triceps, front delts | Accessory work, shoulder comfort |
| Medium | Middle | Chest and triceps together | Most training sets |
| Wide | Shortest | Chest, with more shoulder load | Competition attempts |
Bench angle matters as much as width, and there is a number for it. In the same body of work, a six rep max was 21.5% higher on a flat bench than on a 25 degree incline. It was also 2.5% higher than on a 25 degree decline.
So width and angle pull on the same result from opposite ends. A flat bench with a medium grip is the reference point, and every change from it is a trade against that baseline.
Measure Once, Then Stop Guessing
The measurement that matters is the distance between the two bony points at the back of each shoulder. Those are the acromion points, and a tape across the back gives the number in seconds.
Write it down. That figure is the 100% line, and every grip in the article is a share of it.
Then find the hand position. Lie on the bench with the bar racked, and set the hands so the forearms are upright when the bar touches the chest. A vertical forearm is the sign that the width suits the frame.
If the elbows sit far behind the bar at the bottom, the grip is too narrow for that lifter. If the upper arms are level with the shoulders and the elbows are wide, the grip is at or past the limit.
Competition bars make this repeatable. The ring marks give a fixed reference. The same lifter can find the same grip in any gym, and a coach can write it down as a number.
That is the whole method: one tape measurement at the shoulders, one check of the forearms, and one mark on the bar. It takes two minutes and it replaces a habit that most lifters never examine.
Shoulders, Elbows and the Cost of Wide
Width is not free. The load path from the hand to the shoulder changes with the grip, and the joint feels it before the muscles do.
A wide grip puts the upper arm closer to a right angle to the torso. The bar travel shortens, which is the gain. The shoulder then works at a position where the joint is less supported, which is the cost.
A close grip does the opposite. The bar travels further, the elbows tuck nearer the body, and the triceps take a larger share. Lifters with shoulder trouble often move here, and pay for it with less weight on the bar.
The elbow angle follows the grip. A medium grip lets the elbows sit at roughly 45 degrees from the torso at the bottom. That is the position most coaching material describes as the default.
There is one more check that costs nothing. If a grip feels strong on the first rep and painful by the fifth, the width is too wide for that shoulder on that day. The training set should then be narrower than the competition set.
What the Research Actually Measured
It is worth knowing what these numbers came from, because a single study is not a law.
The activity readings came from a small sample of twelve male college students, all with more than six months of training behind them. That is a beginner-to-intermediate group, and it is not a group of competitive lifters.
The grips were set by ratio, not by feel. Medium was 100% of the shoulder distance, and wide was 200% of it. Wide in that study worked out at 81 cm between the hands, which is the same figure the federations use as a ceiling.
The bench angles were controlled at 25 degrees up, flat, and 25 degrees down. Every lift in the comparison was a six rep max. The figures therefore describe a load that could be repeated six times, and not a single attempt.
Two lessons follow for a buyer or a coach. A ratio travels between lifters and a centimetre figure does not, so write the ratio down. And a result measured on beginners should be checked on the person in front of you before it becomes a rule.
Four Habits That Move the Width
The grip a lifter thinks they use and the grip they actually take are often different. Four habits account for most of the drift.
Unracking wide, then sliding in. A bar taken out of the rack with the hands outside the working width forces a shift on the first rep. That shift is never the same twice. Set the hands before the unrack.
Copying a mark instead of measuring. A ring mark is a reference, and two bars can carry marks with different spacing. Measure the hands once, then find the mark that matches.
Changing width with the load. A grip that holds at 70% often fails at 90%, and the hands drift inward under a heavy bar without anyone deciding to move them. Check the position on the heavy set, not the warm-up.
Ignoring the pad. A bench that is too narrow pulls the shoulder blades off the pad, and the lifter compensates by narrowing the grip. The equipment moved the width before the lifter did.
What the Bar and the Bench Add
A bench press width is set by the lifter, and the equipment either records it or hides it. Three parts of the equipment decide which.
The ring marks. On a competition bar they sit at the width the rules allow. A lifter can then place the index finger inside the ring and know the grip is legal. A bar without marks removes the reference, and grip drifts between sessions.
The shaft diameter. A thinner shaft sits deeper in the hand and changes where the palm contacts the bar. Buyers who specify a bar for a gym are choosing a hand position as much as a piece of steel.
The pad width and the upright spacing. A narrow pad leaves the shoulders hanging over the edge, and uprights set too close force the hands inward when the bar is unracked. Both change the width a lifter can actually use.
| Part | What it fixes | What to ask for |
|---|---|---|
| Ring marks | Repeatable hand position | Marks at the legal width, stamped |
| Shaft diameter | How the bar sits in the palm | Diameter in mm, stated |
| Pad width | Shoulder support | Pad width in cm |
| Upright spacing | Where the hands can go | Inside width between uprights |
These are the lines that a gym buyer can put on a written order. They are also the lines that a listing leaves out, which is why two benches at the same price can suit different lifters.
Six Lines for a Bench and Bar Order
A bench and bar order that can be checked is written in six lines. Each one is a measurement, and each one changes the grip a lifter can actually take.
The bar, with ring marks stated. Mark spacing, shaft diameter and overall length. The marks are the reference a lifter uses to repeat a grip.
The pad, with width and height. Width in centimetres and height from the floor. A pad that is too narrow leaves the shoulders unsupported.
The upright spacing. The clear inside width between uprights, because that decides how far apart the hands can go at the unrack.
The rack position. Height range and the number of settings. A rack with coarse steps forces a compromise on every lifter.
The frame and finish. Steel section, wall thickness and coating. This is what the bench does after two years in a gym.
The load rating, with a test. A figure plus the method behind it. Without the method, the figure is a claim.
| Spec line | Example | Why it matters at the bar |
|---|---|---|
| Ring marks | Marks at the legal width | Repeatable hand position |
| Pad width and height | Width in cm, height from floor | Shoulder support |
| Upright spacing | Clear inside width | Where the hands can go |
| Rack settings | Height range, step count | Fit for every lifter |
| Frame and finish | Section, wall, coating | Life in a gym |
| Load rating and test | Figure plus method | A claim against a check |
Written down, those six lines become a sheet a gym equipment factory can quote on, and two quotes describe the same bench. The marks and load lines then become the script for the check on a finished bench batch.
Freight is priced on weight, and a bench is heavy. The difference between gross and net weight is where a cheap bench stops being cheap.
If a batch arrives with the wrong mark spacing, the remedy has rules. Then the route after a batch that misses follows the sheet, and not the delivery note.
The 81 cm limit, the 100% and 200% ratios, the biceps figures and the bench angle numbers come from a published review of grip width research. An example of a bar with stamped marks and a stated shaft is this bar specification page.
Questions About Bench Press Width
How wide should my bench press grip be?
Start at 100% of the distance between your shoulder points, then move out until your forearms are upright when the bar touches your chest. Never go past 81 cm, which is the competition limit.
What is the maximum legal grip width?
81 cm between the hands, about 31.9 inches, in most powerlifting federations. The ring marks on a competition bar sit so the index finger lands inside them.
Close grip or wide grip for chest?
Wide shortens the stroke and lets more weight move, and it loads the shoulder more. Close lengthens the stroke and shifts work to the triceps. Medium is the usual training default.
Is a wide grip bad for my shoulders?
It is not bad by itself, and it is less forgiving. The upper arm sits further from the body, so the joint takes more load at the bottom. If a grip hurts by the fifth rep, it is too wide for that day.
How do I measure my grip width?
Measure between the two bony points at the back of your shoulders. That is 100%. A medium grip sits there, and a wide grip runs out to twice that distance or 81 cm, whichever comes first.
Does bench angle matter as much as width?
It moves the number about as much. A six rep max was 21.5% higher on a flat bench than on a 25 degree incline, and 2.5% higher than on a 25 degree decline.
The Short Version
Measure the shoulders once. Set the grip at 100% of that distance, then widen it until the forearms are upright at the chest and the hands stay inside 81 cm.
Write the width down with the bar you use. A number that lives on a sheet repeats in every gym, and a feeling does not.
The Marks Are a Specification
A bench quote that lists a colour has skipped the lines that decide who can use it. Send the bar mark spacing, the pad width and the upright spacing you need. We will tell you which two figures to fix before the order is placed.
Send the Brief
Questions & Comments
We read every one and reply within 24 hoursA grip width copied from a video ignores the only measurement that matters: the distance between your own shoulder points. Tell us the width you train at in a comment and we will say which bar line repeats it.