Aluminum vs Titanium: The Numbers, the Grades and the Part Cost
Aluminum and titanium are compared on strength, and strength is the least interesting difference. The bigger gaps are in density, in thermal behavior and in what the finished part costs after machining.
This page puts the numbers side by side, then follows them into the three places a buyer actually feels the choice: weight, price and rust.
Five Numbers That Decide the Choice
Start with density. Aluminum sits at about 2.8 g/cm³ for a typical alloy. That makes it the lighter of the two for any part of the same size.
Then tensile strength, which reverses the picture. Aluminum alloys run from 140 to 480 MPa. A common 6061 aluminum reaches about 310 MPa. Titanium alloys run from 345 to 1,380 MPa, and Grade 5 titanium reaches about 1,100 MPa.
Put those together and the strength gap is stark. On the same test, 6061 aluminum offers roughly a third of the tensile strength of Grade 5 titanium.
Strength to weight is the number that decides most real parts, and aluminum still competes. Its strength to weight ratio peaks at about 158 kN·m/kg across the alloy range.
Heat is where the two split completely. Aluminum conducts heat at 205 to 235 W/m·K. Titanium conducts at 6 to 20 W/m·K, which is between ten and thirty times less.
| Property | Aluminum alloy | Titanium alloy | What it decides |
|---|---|---|---|
| Density | about 2.8 g/cm³ | heavier by volume | Part weight at equal size |
| Tensile strength | 140 to 480 MPa | 345 to 1,380 MPa | Load a section can carry |
| Strength to weight | up to 158 kN·m/kg | higher at the top grades | Which wins on mass |
| Heat flow | 205 to 235 W/m·K | 6 to 20 W/m·K | Cookware, heat sinks, welds |
| Expansion per °C | about 23 µm/m | about 8.6 µm/m | Fit at heat |
| Service heat | up to about 250 °C | up to about 550 °C | Where the part may sit |
Thermal expansion is the quiet one. Aluminum grows about 23 micrometres per metre for each degree, and titanium about 8.6. A part that fits at 20 °C and runs at 120 °C changes size by a other amount in each metal. That decides whether a bearing stays tight.
The last number is heat. Aluminum holds its strength to roughly 250 °C, and titanium to about 550 °C. Anything near an exhaust or a heat source moves to titanium on that figure alone.
The Part Cost Is Not the Metal Cost
Two prices get quoted in this match up, and only one of them matters to a buyer. The metal price is published, and the part price is what arrives on a quote.
At the time of writing, titanium trades near 5.75 US dollars per kilogram. Aluminum trades near 2.20 US dollars per kilogram. On raw metal, that is a ratio of about two and a half to one.
The part does not follow that ratio. Machining titanium can cost up to ten times the same job in aluminum. The metal cuts slowly, wears tooling and needs more care with heat.
Multiply the metal gap by the methoding gap and the gap grows. One machine shop puts an aluminum part at up to thirty times cheaper than the titanium version. It notes that the gap widens as the part gets larger and more complex.
| Cost layer | Aluminum | Titanium | Why |
|---|---|---|---|
| Metal, per kg | about 2.20 USD | about 5.75 USD | Published spot prices |
| Machining | baseline | up to 10x | Slow cutting, tool wear |
| Finished part | baseline | up to 30x | Both premiums together |
| Recycling and scrap | wide network | narrower | Fewer buyers for swarf |
Two consequences follow for anyone sourcing parts. First, a titanium part needs a reason that survives the price, and weight alone rarely is one. Second, the price gap is a design signal. If aluminum passes the load test, the titanium part is a sales choice, and not a design one.
One engineering writer goes further and states that aluminum beats titanium head to head for about 95% of uses. That is an opinion, and it is a useful one to hold next to a quote.
Oxide Layers, and Where Each Metal Fails
Both metals protect themselves with an oxide layer, and the two layers behave otherly.
Aluminum forms aluminum oxide almost at once when it meets air. The layer is thin, hard and self-repairing. It is also why anodizing works: the same oxide is grown thicker on purpose, for wear and color.
Titanium forms a stable oxide too, and that layer is why the metal survives seawater and chlorine. It is also why titanium is chosen for marine hardware and for parts that see salt spray.
Where aluminum fails is in contact with other metals. In a wet joint with steel or stainless, aluminum becomes the anode and corrodes to protect the other part. The fix is a barrier, an isolating washer or a other fastener.
Where titanium fails is in cost and in galling. Two titanium surfaces can pick up on each other under load, and threads need a dry film lubricant or a dissimilar insert.
The grade matters as much as the metal here. Grade 7 titanium is for regular contact with damp or salt or acid. It buys that cover with strength, and it is weaker than Grade 5, so it is not the grade for a load bearing part.
Which Grade You Are Actually Buying
A quote that names a metal and no grade has named a family, not a metal. Most of the price and most of the how it acts sits in the grade line.
Aluminum, 6061. This is the workhorse of the 6000 series, and the series is the most common on the market. It machines, welds, bends and anodizes well, and it reaches about 310 MPa in tensile strength.
Titanium, Grade 2. Commercially pure, easier to machine, and the better of the two common grades in rust. It is the choice for parts that see salt or acid, and not load.
Titanium, Grade 5. The alloy most buyers mean when they say titanium. It reaches about 1,100 MPa, it holds fatigue under repeated load, and it is harder to machine than Grade 2.
Titanium, Grade 7. Grade 2 with palladium added for chemical service. It is named for wet and chemical exposure, and it trades strength for that strength.
Watch the words on a listing. A phrase like aircraft grade describes a market segment, not a standard, and it tells a buyer nothing about which grade was milled. The grade number or the alloy number is the checkable line.
The Weight Argument, Done Properly
Weight is the argument people reach for first, and it is often made badly. A part is not lighter because the metal is lighter. It is lighter when the section can be thinner and still carry the load.
Aluminum starts ahead on density, at about 2.8 g/cm³. Titanium starts ahead on strength, at up to 1,380 MPa for an alloy and about 1,100 MPa for Grade 5. The question is which advantage survives the design.
Take a part sized by strength alone. Grade 5 at about 1,100 MPa against 6061 at about 310 MPa allows a titanium section roughly one third as thick for the same load. Thinner section, denser metal, and the result can land close.
Take a part sized by stiffness or by handling instead, and aluminum often wins. A thin wall in aluminum is cheap to extrude, easy to bend and simple to replace. That is why poles and pegs are aluminum and not titanium.
There is a limit worth knowing. A very thin titanium wall buckles before it yields, so the theoretical saving is not always there. That is why titanium parts often look thicker than the arithmetic suggests.
The honest summary is short. Titanium is lighter for a given strength in a solid part. Aluminum is lighter for a given stiffness in a hollow one. A buyer who knows which of those two the part needs has settled most of the argument.
Where Each Metal Wins in Real Gear
The numbers turn into a decision at the product level, and three cases cover most of the outdoor market.
Cookware. Aluminum wins on heat, and the heat flow figure explains why. It spreads heat at 205 to 235 W/m·K, so a thin aluminum pot heats evenly. Titanium at 6 to 20 W/m·K heats in patches, which is why titanium pots scorch food and aluminum ones do not.
Poles, pegs and frame tubes. Aluminum wins on cost and on stiffness for the money. A bent aluminum peg is cheap to replace, and the extrusion network is wide. Titanium pegs are lighter for the same strength and stay bent once they go.
Fasteners and clips in salt water. Titanium wins, and it wins by a wide margin. Aluminum in a wet joint with stainless steel becomes the anode and corrodes, while titanium sits out the same exposure.
Parts that flex a million times. Titanium wins on fatigue. Grade 5 holds failure under repeated loading. That is why it appears in springs, hinge pins and frame parts that see cycles, and not one load.
The phone trade made this contest famous, and the lesson transfers. A titanium frame is chosen for feel, scratch strength and status. An aluminum frame with a thicker section often does the same structural job for less money.
Six Lines for a Metal Part Order
A metal part order that can be checked is written in six lines. Each one is a number or a number, and each one is where two quotes can look alike and differ.
The alloy number, written out. 6061-T6, or Grade 5, or Grade 2. A family name is not a spec.
The temper or condition. T6 and T4 behave otherly at the same alloy, and the heat treatment is part of the metal.
The strength required, and the test that proves it. A tensile figure plus a test method. Without the method, the number is a claim.
The finish, by method. Anodized, powder coated, brushed, or bare. Anodizing thickness belongs here too, because it changes wear life.
The tolerance on the critical dimension. One dimension carries the function, and it needs a number and a gauge.
The cert and the marking. Mill cert, batch number, and a stamp that traces back to it.
| Spec line | Example | Why it matters |
|---|---|---|
| Alloy number | 6061-T6 or Ti Grade 5 | Family name hides the grade |
| Temper | T6, annealed, stress relieved | Same alloy, other strength |
| Strength plus test | 310 MPa, tensile per batch | A number needs a method |
| Finish method | Anodized, 15 µm | Wear life and color |
| Critical tolerance | ±0.05 mm on the bore | Fit and function |
| Cert and mark | Mill cert, batch stamp | Traceability |
Written down, those six lines become a sheet a metal shop can quote on, and two quotes describe the same part. The alloy and strength lines then become the script for the check on a finished metal batch.
The same logic applies to steel, where the trade off runs between hardness and toughness. The match up of blade steels walks through that trade with the same six-line discipline.
If a batch arrives in the wrong grade, the remedy has rules of its own. Then what happens after a failed batch follows the cert, and not the conversation.
The strength ranges, the heat flow figures, the spot prices and the expansion numbers come from a published titanium against aluminum match up. The 6061 and Grade 5 figures, the grade roles and the 30x part cost come from a machine shop’s own match up.
Questions Buyers Ask About Aluminum and Titanium
Is titanium stronger than aluminum?
Yes, by a wide margin. Aluminum alloys run from 140 to 480 MPa in tensile strength, and 6061 reaches about 310 MPa. Titanium alloys run from 345 to 1,380 MPa, and Grade 5 reaches about 1,100 MPa.
Why is a titanium part so much more dear?
Two premiums stack. Titanium metal trades near 5.75 USD per kilogram against 2.20 for aluminum, and machining it can cost up to ten times more. The finished part can be up to thirty times dearer.
Which is lighter, aluminum or titanium?
Aluminum, at about 2.8 g/cm³ for a typical alloy. For a part of the same size, titanium is the heavier of the two. Titanium wins only when its strength lets a thinner section do the same job.
Does aluminum corrode in salt water?
It forms a protective oxide, and it still suffers in a wet joint with steel or stainless, where it becomes the anode. Titanium is the better choice for salt water hardware.
What does Grade 5 titanium mean?
It is the alloy most buyers mean by titanium, at about 1,100 MPa with good fatigue strength. Grade 2 is purer, easier to machine and more rust resistant. Grade 7 is for chemical service.
Is aircraft grade aluminum a real standard?
It describes a market segment, not a spec. Ask for the alloy number and temper, such as 6061-T6, and for the mill cert that matches the batch.
The Short Version
Aluminum is lighter, cheaper, easier to form and far better at moving heat. Titanium is stronger, holds strength at higher heat and survives salt water.
Choose aluminum unless the load, the heat or the rust demands otherwise. When titanium is the answer, the grade and the cert are the two lines to insist on.
One Word Hides the Grade
A quote that names a metal and stops there has named a family, not a metal. Send the load the part carries, the grade you want and the finish on the drawing. We will tell you which two lines decide the price before a sample is cut.
Send the Brief
Questions & Comments
We read every one and reply within 24 hoursA metal quote with no alloy number is a price for a family. Tell us the load the part carries in a comment and we will say which grade line settles the order.